From f9004dbfff8a3fbbd7e2a88c8a4327c7f2f8e5b2 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Wed, 31 Jan 2024 01:04:47 +0000
Subject: [PATCH] add driver 5G
---
kernel/arch/arm/boot/dts/qcom-pm8941.dtsi | 49 +++++++++++++------------------------------------
1 files changed, 13 insertions(+), 36 deletions(-)
diff --git a/kernel/arch/arm/boot/dts/qcom-pm8941.dtsi b/kernel/arch/arm/boot/dts/qcom-pm8941.dtsi
index 2515c5c..c1f2012 100644
--- a/kernel/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/kernel/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -63,43 +63,10 @@
compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
reg = <0xc000>;
gpio-controller;
+ gpio-ranges = <&pm8941_gpios 0 0 36>;
#gpio-cells = <2>;
- interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
- <0 0xc1 0 IRQ_TYPE_NONE>,
- <0 0xc2 0 IRQ_TYPE_NONE>,
- <0 0xc3 0 IRQ_TYPE_NONE>,
- <0 0xc4 0 IRQ_TYPE_NONE>,
- <0 0xc5 0 IRQ_TYPE_NONE>,
- <0 0xc6 0 IRQ_TYPE_NONE>,
- <0 0xc7 0 IRQ_TYPE_NONE>,
- <0 0xc8 0 IRQ_TYPE_NONE>,
- <0 0xc9 0 IRQ_TYPE_NONE>,
- <0 0xca 0 IRQ_TYPE_NONE>,
- <0 0xcb 0 IRQ_TYPE_NONE>,
- <0 0xcc 0 IRQ_TYPE_NONE>,
- <0 0xcd 0 IRQ_TYPE_NONE>,
- <0 0xce 0 IRQ_TYPE_NONE>,
- <0 0xcf 0 IRQ_TYPE_NONE>,
- <0 0xd0 0 IRQ_TYPE_NONE>,
- <0 0xd1 0 IRQ_TYPE_NONE>,
- <0 0xd2 0 IRQ_TYPE_NONE>,
- <0 0xd3 0 IRQ_TYPE_NONE>,
- <0 0xd4 0 IRQ_TYPE_NONE>,
- <0 0xd5 0 IRQ_TYPE_NONE>,
- <0 0xd6 0 IRQ_TYPE_NONE>,
- <0 0xd7 0 IRQ_TYPE_NONE>,
- <0 0xd8 0 IRQ_TYPE_NONE>,
- <0 0xd9 0 IRQ_TYPE_NONE>,
- <0 0xda 0 IRQ_TYPE_NONE>,
- <0 0xdb 0 IRQ_TYPE_NONE>,
- <0 0xdc 0 IRQ_TYPE_NONE>,
- <0 0xdd 0 IRQ_TYPE_NONE>,
- <0 0xde 0 IRQ_TYPE_NONE>,
- <0 0xdf 0 IRQ_TYPE_NONE>,
- <0 0xe0 0 IRQ_TYPE_NONE>,
- <0 0xe1 0 IRQ_TYPE_NONE>,
- <0 0xe2 0 IRQ_TYPE_NONE>,
- <0 0xe3 0 IRQ_TYPE_NONE>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
boost_bypass_n_pin: boost-bypass {
pins = "gpio21";
@@ -211,6 +178,16 @@
qcom,vs-soft-start-strength = <0>;
regulator-initial-mode = <1>;
};
+
+ pm8941_5vs2: 5vs2 {
+ regulator-enable-ramp-delay = <1000>;
+ regulator-pull-down;
+ regulator-over-current-protection;
+ qcom,ocp-max-retries = <10>;
+ qcom,ocp-retry-delay = <30>;
+ qcom,vs-soft-start-strength = <0>;
+ regulator-initial-mode = <1>;
+ };
};
};
};
--
Gitblit v1.6.2