From f9004dbfff8a3fbbd7e2a88c8a4327c7f2f8e5b2 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Wed, 31 Jan 2024 01:04:47 +0000
Subject: [PATCH] add driver 5G

---
 kernel/arch/arm/boot/dts/lpc3250-phy3250.dts |   98 +++++++++++++++++++++++++++----------------------
 1 files changed, 54 insertions(+), 44 deletions(-)

diff --git a/kernel/arch/arm/boot/dts/lpc3250-phy3250.dts b/kernel/arch/arm/boot/dts/lpc3250-phy3250.dts
index ffcf786..21a6d0b 100644
--- a/kernel/arch/arm/boot/dts/lpc3250-phy3250.dts
+++ b/kernel/arch/arm/boot/dts/lpc3250-phy3250.dts
@@ -1,14 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
 /*
  * PHYTEC phyCORE-LPC3250 board
  *
+ * Copyright (C) 2015-2019 Vladimir Zapolskiy <vz@mleia.com>
  * Copyright 2012 Roland Stigge <stigge@antcom.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 /dts-v1/;
@@ -17,43 +12,10 @@
 / {
 	model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250";
 	compatible = "phytec,phy3250", "nxp,lpc3250";
-	#address-cells = <1>;
-	#size-cells = <1>;
 
-	memory {
+	memory@80000000 {
 		device_type = "memory";
 		reg = <0x80000000 0x4000000>;
-	};
-
-	regulators {
-		backlight_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			regulator-name = "backlight_reg";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			gpio = <&gpio 5 4 0>;
-			enable-active-high;
-			regulator-boot-on;
-		};
-
-		lcd_reg: regulator@1 {
-			compatible = "regulator-fixed";
-			regulator-name = "lcd_reg";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			gpio = <&gpio 5 0 0>;
-			enable-active-high;
-			regulator-boot-on;
-		};
-
-		sd_reg: regulator@2 {
-			compatible = "regulator-fixed";
-			regulator-name = "sd_reg";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio 5 5 0>;
-			enable-active-high;
-		};
 	};
 
 	leds {
@@ -69,10 +31,59 @@
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	panel: panel {
+		compatible = "sharp,lq035q7db03";
+		power-supply = <&reg_lcd>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&cldc_output>;
+			};
+		};
+	};
+
+	reg_backlight: regulator-backlight {
+		compatible = "regulator-fixed";
+		regulator-name = "backlight";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio 5 4 0>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	reg_lcd: regulator-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio 5 0 0>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	reg_sd: regulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio 5 5 0>;
+		enable-active-high;
+		regulator-boot-on;
+	};
 };
 
 &clcd {
+	max-memory-bandwidth = <18710000>;
 	status = "okay";
+
+	port {
+		cldc_output: endpoint {
+			remote-endpoint = <&panel_input>;
+			arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
+		};
+	};
 };
 
 &i2c1 {
@@ -117,6 +128,7 @@
 &mac {
 	phy-mode = "rmii";
 	use-iram;
+	status = "okay";
 };
 
 /* Here, choose exactly one from: ohci, usbd */
@@ -130,7 +142,7 @@
 	cd-gpios = <&gpio 3 1 0>;
 	cd-inverted;
 	bus-width = <4>;
-	vmmc-supply = <&sd_reg>;
+	vmmc-supply = <&reg_sd>;
 	status = "okay";
 };
 
@@ -184,8 +196,6 @@
 };
 
 &ssp0 {
-	#address-cells = <1>;
-	#size-cells = <0>;
 	num-cs = <1>;
 	cs-gpios = <&gpio 3 5 0>;
 	status = "okay";

--
Gitblit v1.6.2