From f70575805708cabdedea7498aaa3f710fde4d920 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Wed, 31 Jan 2024 03:29:01 +0000
Subject: [PATCH] add lvds1024*800
---
kernel/drivers/acpi/sleep.c | 306 ++++++++++++++++++++++++++++++--------------------
1 files changed, 183 insertions(+), 123 deletions(-)
diff --git a/kernel/drivers/acpi/sleep.c b/kernel/drivers/acpi/sleep.c
index 847db3e..097a5b5 100644
--- a/kernel/drivers/acpi/sleep.c
+++ b/kernel/drivers/acpi/sleep.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
/*
* sleep.c - ACPI sleep support.
*
@@ -5,9 +6,6 @@
* Copyright (c) 2004 David Shaohua Li <shaohua.li@intel.com>
* Copyright (c) 2000-2003 Patrick Mochel
* Copyright (c) 2003 Open Source Development Lab
- *
- * This file is released under the GPLv2.
- *
*/
#include <linux/delay.h>
@@ -63,8 +61,11 @@
static int acpi_sleep_prepare(u32 acpi_state)
{
#ifdef CONFIG_ACPI_SLEEP
+ unsigned long acpi_wakeup_address;
+
/* do we have a wakeup address for S2 and S3? */
if (acpi_state == ACPI_STATE_S3) {
+ acpi_wakeup_address = acpi_get_wakeup_address();
if (!acpi_wakeup_address)
return -EFAULT;
acpi_set_waking_vector(acpi_wakeup_address);
@@ -79,7 +80,7 @@
return 0;
}
-static bool acpi_sleep_state_supported(u8 sleep_state)
+bool acpi_sleep_state_supported(u8 sleep_state)
{
acpi_status status;
u8 type_a, type_b;
@@ -91,6 +92,10 @@
}
#ifdef CONFIG_ACPI_SLEEP
+static bool sleep_no_lps0 __read_mostly;
+module_param(sleep_no_lps0, bool, 0644);
+MODULE_PARM_DESC(sleep_no_lps0, "Do not use the special LPS0 device interface");
+
static u32 acpi_target_sleep_state = ACPI_STATE_S0;
u32 acpi_target_system_state(void)
@@ -160,11 +165,11 @@
return 0;
}
-static bool acpi_sleep_no_lps0;
+static bool acpi_sleep_default_s3;
-static int __init init_no_lps0(const struct dmi_system_id *d)
+static int __init init_default_s3(const struct dmi_system_id *d)
{
- acpi_sleep_no_lps0 = true;
+ acpi_sleep_default_s3 = true;
return 0;
}
@@ -359,17 +364,12 @@
DMI_MATCH(DMI_PRODUCT_NAME, "80E3"),
},
},
- /*
- * https://bugzilla.kernel.org/show_bug.cgi?id=196907
- * Some Dell XPS13 9360 cannot do suspend-to-idle using the Low Power
- * S0 Idle firmware interface.
- */
{
- .callback = init_no_lps0,
- .ident = "Dell XPS13 9360",
+ .callback = init_nvs_save_s3,
+ .ident = "Lenovo G40-45",
.matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
- DMI_MATCH(DMI_PRODUCT_NAME, "XPS 13 9360"),
+ DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "80E1"),
},
},
/*
@@ -378,11 +378,23 @@
* https://bugzilla.kernel.org/show_bug.cgi?id=199057).
*/
{
- .callback = init_no_lps0,
+ .callback = init_default_s3,
.ident = "ThinkPad X1 Tablet(2016)",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
DMI_MATCH(DMI_PRODUCT_NAME, "20GGA00L00"),
+ },
+ },
+ /*
+ * ASUS B1400CEAE hangs on resume from suspend (see
+ * https://bugzilla.kernel.org/show_bug.cgi?id=215742).
+ */
+ {
+ .callback = init_default_s3,
+ .ident = "ASUS B1400CEAE",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "ASUS EXPERTBOOK B1400CEAE"),
},
},
{},
@@ -454,14 +466,6 @@
return error;
}
-static int find_powerf_dev(struct device *dev, void *data)
-{
- struct acpi_device *device = to_acpi_device(dev);
- const char *hid = acpi_device_hid(device);
-
- return !strcmp(hid, ACPI_BUTTON_HID_POWERF);
-}
-
/**
* acpi_pm_finish - Instruct the platform to leave a sleep state.
*
@@ -470,7 +474,7 @@
*/
static void acpi_pm_finish(void)
{
- struct device *pwr_btn_dev;
+ struct acpi_device *pwr_btn_adev;
u32 acpi_state = acpi_target_sleep_state;
acpi_ec_unblock_transactions();
@@ -501,11 +505,11 @@
return;
pwr_btn_event_pending = false;
- pwr_btn_dev = bus_find_device(&acpi_bus_type, NULL, NULL,
- find_powerf_dev);
- if (pwr_btn_dev) {
- pm_wakeup_event(pwr_btn_dev, 0);
- put_device(pwr_btn_dev);
+ pwr_btn_adev = acpi_dev_get_first_match_dev(ACPI_BUTTON_HID_POWERF,
+ NULL, -1);
+ if (pwr_btn_adev) {
+ pm_wakeup_event(&pwr_btn_adev->dev, 0);
+ acpi_dev_put(pwr_btn_adev);
}
}
@@ -534,8 +538,9 @@
acpi_sleep_tts_switch(acpi_target_sleep_state);
}
#else /* !CONFIG_ACPI_SLEEP */
+#define sleep_no_lps0 (1)
#define acpi_target_sleep_state ACPI_STATE_S0
-#define acpi_sleep_no_lps0 (false)
+#define acpi_sleep_default_s3 (1)
static inline void acpi_sleep_dmi_check(void) {}
#endif /* CONFIG_ACPI_SLEEP */
@@ -701,7 +706,6 @@
.recover = acpi_pm_finish,
};
-static bool s2idle_in_progress;
static bool s2idle_wakeup;
/*
@@ -914,41 +918,42 @@
if (lps0_device_handle)
return 0;
- if (acpi_sleep_no_lps0) {
- acpi_handle_info(adev->handle,
- "Low Power S0 Idle interface disabled\n");
- return 0;
- }
-
if (!(acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0))
return 0;
guid_parse(ACPI_LPS0_DSM_UUID, &lps0_dsm_guid);
/* Check if the _DSM is present and as expected. */
out_obj = acpi_evaluate_dsm(adev->handle, &lps0_dsm_guid, 1, 0, NULL);
- if (out_obj && out_obj->type == ACPI_TYPE_BUFFER) {
- char bitmask = *(char *)out_obj->buffer.pointer;
-
- lps0_dsm_func_mask = bitmask;
- lps0_device_handle = adev->handle;
- /*
- * Use suspend-to-idle by default if the default
- * suspend mode was not set from the command line.
- */
- if (mem_sleep_default > PM_SUSPEND_MEM)
- mem_sleep_current = PM_SUSPEND_TO_IDLE;
-
- acpi_handle_debug(adev->handle, "_DSM function mask: 0x%x\n",
- bitmask);
-
- acpi_ec_mark_gpe_for_wake();
- } else {
+ if (!out_obj || out_obj->type != ACPI_TYPE_BUFFER) {
acpi_handle_debug(adev->handle,
"_DSM function 0 evaluation failed\n");
+ return 0;
}
+
+ lps0_dsm_func_mask = *(char *)out_obj->buffer.pointer;
+
ACPI_FREE(out_obj);
+ acpi_handle_debug(adev->handle, "_DSM function mask: 0x%x\n",
+ lps0_dsm_func_mask);
+
+ lps0_device_handle = adev->handle;
+
lpi_device_get_constraints();
+
+ /*
+ * Use suspend-to-idle by default if the default suspend mode was not
+ * set from the command line.
+ */
+ if (mem_sleep_default > PM_SUSPEND_MEM && !acpi_sleep_default_s3)
+ mem_sleep_current = PM_SUSPEND_TO_IDLE;
+
+ /*
+ * Some LPS0 systems, like ASUS Zenbook UX430UNR/i7-8550U, require the
+ * EC GPE to be enabled while suspended for certain wakeup devices to
+ * work, so mark it as wakeup-capable.
+ */
+ acpi_ec_mark_gpe_for_wake();
return 0;
}
@@ -961,97 +966,149 @@
static int acpi_s2idle_begin(void)
{
acpi_scan_lock_acquire();
- s2idle_in_progress = true;
return 0;
}
static int acpi_s2idle_prepare(void)
{
- if (lps0_device_handle) {
- acpi_sleep_run_lps0_dsm(ACPI_LPS0_SCREEN_OFF);
- acpi_sleep_run_lps0_dsm(ACPI_LPS0_ENTRY);
-
+ if (acpi_sci_irq_valid()) {
+ enable_irq_wake(acpi_sci_irq);
acpi_ec_set_gpe_wake_mask(ACPI_GPE_ENABLE);
}
-
- if (acpi_sci_irq_valid())
- enable_irq_wake(acpi_sci_irq);
acpi_enable_wakeup_devices(ACPI_STATE_S0);
/* Change the configuration of GPEs to avoid spurious wakeup. */
acpi_enable_all_wakeup_gpes();
acpi_os_wait_events_complete();
+
+ s2idle_wakeup = true;
return 0;
}
-static void acpi_s2idle_wake(void)
+static int acpi_s2idle_prepare_late(void)
{
+ if (!lps0_device_handle || sleep_no_lps0)
+ return 0;
if (pm_debug_messages_on)
lpi_check_constraints();
- /*
- * If IRQD_WAKEUP_ARMED is not set for the SCI at this point, it means
- * that the SCI has triggered while suspended, so cancel the wakeup in
- * case it has not been a wakeup event (the GPEs will be checked later).
- */
- if (acpi_sci_irq_valid() &&
- !irqd_is_wakeup_armed(irq_get_irq_data(acpi_sci_irq))) {
- pm_system_cancel_wakeup();
- s2idle_wakeup = true;
- /*
- * On some platforms with the LPS0 _DSM device noirq resume
- * takes too much time for EC wakeup events to survive, so look
- * for them now.
- */
- if (lps0_device_handle)
- acpi_ec_dispatch_gpe();
- }
+ acpi_sleep_run_lps0_dsm(ACPI_LPS0_SCREEN_OFF);
+ acpi_sleep_run_lps0_dsm(ACPI_LPS0_ENTRY);
+
+ return 0;
}
-static void acpi_s2idle_sync(void)
+static bool acpi_s2idle_wake(void)
{
- /*
- * Process all pending events in case there are any wakeup ones.
- *
- * The EC driver uses the system workqueue and an additional special
- * one, so those need to be flushed too.
- */
- acpi_os_wait_events_complete(); /* synchronize SCI IRQ handling */
- acpi_ec_flush_work();
- acpi_os_wait_events_complete(); /* synchronize Notify handling */
- s2idle_wakeup = false;
+ if (!acpi_sci_irq_valid())
+ return pm_wakeup_pending();
+
+ while (pm_wakeup_pending()) {
+ /*
+ * If IRQD_WAKEUP_ARMED is set for the SCI at this point, the
+ * SCI has not triggered while suspended, so bail out (the
+ * wakeup is pending anyway and the SCI is not the source of
+ * it).
+ */
+ if (irqd_is_wakeup_armed(irq_get_irq_data(acpi_sci_irq))) {
+ pm_pr_dbg("Wakeup unrelated to ACPI SCI\n");
+ return true;
+ }
+
+ /*
+ * If the status bit of any enabled fixed event is set, the
+ * wakeup is regarded as valid.
+ */
+ if (acpi_any_fixed_event_status_set()) {
+ pm_pr_dbg("ACPI fixed event wakeup\n");
+ return true;
+ }
+
+ /* Check wakeups from drivers sharing the SCI. */
+ if (acpi_check_wakeup_handlers()) {
+ pm_pr_dbg("ACPI custom handler wakeup\n");
+ return true;
+ }
+
+ /* Check non-EC GPE wakeups and dispatch the EC GPE. */
+ if (acpi_ec_dispatch_gpe()) {
+ pm_pr_dbg("ACPI non-EC GPE wakeup\n");
+ return true;
+ }
+
+ /*
+ * Cancel the SCI wakeup and process all pending events in case
+ * there are any wakeup ones in there.
+ *
+ * Note that if any non-EC GPEs are active at this point, the
+ * SCI will retrigger after the rearming below, so no events
+ * should be missed by canceling the wakeup here.
+ */
+ pm_system_cancel_wakeup();
+ acpi_os_wait_events_complete();
+
+ /*
+ * The SCI is in the "suspended" state now and it cannot produce
+ * new wakeup events till the rearming below, so if any of them
+ * are pending here, they must be resulting from the processing
+ * of EC events above or coming from somewhere else.
+ */
+ if (pm_wakeup_pending()) {
+ pm_pr_dbg("Wakeup after ACPI Notify sync\n");
+ return true;
+ }
+
+ pm_wakeup_clear(acpi_sci_irq);
+ rearm_wake_irq(acpi_sci_irq);
+ }
+
+ return false;
+}
+
+static void acpi_s2idle_restore_early(void)
+{
+ if (!lps0_device_handle || sleep_no_lps0)
+ return;
+
+ acpi_sleep_run_lps0_dsm(ACPI_LPS0_EXIT);
+ acpi_sleep_run_lps0_dsm(ACPI_LPS0_SCREEN_ON);
}
static void acpi_s2idle_restore(void)
{
+ /*
+ * Drain pending events before restoring the working-state configuration
+ * of GPEs.
+ */
+ acpi_os_wait_events_complete(); /* synchronize GPE processing */
+ acpi_ec_flush_work(); /* flush the EC driver's workqueues */
+ acpi_os_wait_events_complete(); /* synchronize Notify handling */
+
+ s2idle_wakeup = false;
+
acpi_enable_all_runtime_gpes();
acpi_disable_wakeup_devices(ACPI_STATE_S0);
- if (acpi_sci_irq_valid())
- disable_irq_wake(acpi_sci_irq);
-
- if (lps0_device_handle) {
+ if (acpi_sci_irq_valid()) {
acpi_ec_set_gpe_wake_mask(ACPI_GPE_DISABLE);
-
- acpi_sleep_run_lps0_dsm(ACPI_LPS0_EXIT);
- acpi_sleep_run_lps0_dsm(ACPI_LPS0_SCREEN_ON);
+ disable_irq_wake(acpi_sci_irq);
}
}
static void acpi_s2idle_end(void)
{
- s2idle_in_progress = false;
acpi_scan_lock_release();
}
static const struct platform_s2idle_ops acpi_s2idle_ops = {
.begin = acpi_s2idle_begin,
.prepare = acpi_s2idle_prepare,
+ .prepare_late = acpi_s2idle_prepare_late,
.wake = acpi_s2idle_wake,
- .sync = acpi_s2idle_sync,
+ .restore_early = acpi_s2idle_restore_early,
.restore = acpi_s2idle_restore,
.end = acpi_s2idle_end,
};
@@ -1072,7 +1129,6 @@
}
#else /* !CONFIG_SUSPEND */
-#define s2idle_in_progress (false)
#define s2idle_wakeup (false)
#define lps0_device_handle (NULL)
static inline void acpi_sleep_suspend_setup(void) {}
@@ -1081,11 +1137,6 @@
bool acpi_s2idle_wakeup(void)
{
return s2idle_wakeup;
-}
-
-bool acpi_sleep_no_ec_events(void)
-{
- return !s2idle_in_progress || !lps0_device_handle;
}
#ifdef CONFIG_PM_SLEEP
@@ -1131,15 +1182,19 @@
nosigcheck = true;
}
-static int acpi_hibernation_begin(void)
+static int acpi_hibernation_begin(pm_message_t stage)
{
- int error;
+ if (!nvs_nosave) {
+ int error = suspend_nvs_alloc();
+ if (error)
+ return error;
+ }
- error = nvs_nosave ? 0 : suspend_nvs_alloc();
- if (!error)
- acpi_pm_start(ACPI_STATE_S4);
+ if (stage.event == PM_EVENT_HIBERNATE)
+ pm_set_suspend_via_firmware();
- return error;
+ acpi_pm_start(ACPI_STATE_S4);
+ return 0;
}
static int acpi_hibernation_enter(void)
@@ -1199,7 +1254,7 @@
* function is used if the pre-ACPI 2.0 suspend ordering has been
* requested.
*/
-static int acpi_hibernation_begin_old(void)
+static int acpi_hibernation_begin_old(pm_message_t stage)
{
int error;
/*
@@ -1210,16 +1265,21 @@
acpi_sleep_tts_switch(ACPI_STATE_S4);
error = acpi_sleep_prepare(ACPI_STATE_S4);
+ if (error)
+ return error;
- if (!error) {
- if (!nvs_nosave)
- error = suspend_nvs_alloc();
- if (!error) {
- acpi_target_sleep_state = ACPI_STATE_S4;
- acpi_scan_lock_acquire();
- }
+ if (!nvs_nosave) {
+ error = suspend_nvs_alloc();
+ if (error)
+ return error;
}
- return error;
+
+ if (stage.event == PM_EVENT_HIBERNATE)
+ pm_set_suspend_via_firmware();
+
+ acpi_target_sleep_state = ACPI_STATE_S4;
+ acpi_scan_lock_acquire();
+ return 0;
}
/*
--
Gitblit v1.6.2