From d2ccde1c8e90d38cee87a1b0309ad2827f3fd30d Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Mon, 11 Dec 2023 02:45:28 +0000
Subject: [PATCH] add boot partition size
---
kernel/include/uapi/linux/ethtool.h | 221 +++++++++++++++++++++++++++++++++++++++++++++++++------
1 files changed, 196 insertions(+), 25 deletions(-)
diff --git a/kernel/include/uapi/linux/ethtool.h b/kernel/include/uapi/linux/ethtool.h
index 35b11c2..13772f0 100644
--- a/kernel/include/uapi/linux/ethtool.h
+++ b/kernel/include/uapi/linux/ethtool.h
@@ -91,10 +91,6 @@
* %ETHTOOL_GSET to get the current values before making specific
* changes and then applying them with %ETHTOOL_SSET.
*
- * Drivers that implement set_settings() should validate all fields
- * other than @cmd that are not described as read-only or deprecated,
- * and must ignore all fields described as read-only.
- *
* Deprecated fields should be ignored by both users and drivers.
*/
struct ethtool_cmd {
@@ -256,9 +252,39 @@
#define DOWNSHIFT_DEV_DEFAULT_COUNT 0xff
#define DOWNSHIFT_DEV_DISABLE 0
+/* Time in msecs after which link is reported as down
+ * 0 = lowest time supported by the PHY
+ * 0xff = off, link down detection according to standard
+ */
+#define ETHTOOL_PHY_FAST_LINK_DOWN_ON 0
+#define ETHTOOL_PHY_FAST_LINK_DOWN_OFF 0xff
+
+/* Energy Detect Power Down (EDPD) is a feature supported by some PHYs, where
+ * the PHY's RX & TX blocks are put into a low-power mode when there is no
+ * link detected (typically cable is un-plugged). For RX, only a minimal
+ * link-detection is available, and for TX the PHY wakes up to send link pulses
+ * to avoid any lock-ups in case the peer PHY may also be running in EDPD mode.
+ *
+ * Some PHYs may support configuration of the wake-up interval for TX pulses,
+ * and some PHYs may support only disabling TX pulses entirely. For the latter
+ * a special value is required (ETHTOOL_PHY_EDPD_NO_TX) so that this can be
+ * configured from userspace (should the user want it).
+ *
+ * The interval units for TX wake-up are in milliseconds, since this should
+ * cover a reasonable range of intervals:
+ * - from 1 millisecond, which does not sound like much of a power-saver
+ * - to ~65 seconds which is quite a lot to wait for a link to come up when
+ * plugging a cable
+ */
+#define ETHTOOL_PHY_EDPD_DFLT_TX_MSECS 0xffff
+#define ETHTOOL_PHY_EDPD_NO_TX 0xfffe
+#define ETHTOOL_PHY_EDPD_DISABLE 0
+
enum phy_tunable_id {
ETHTOOL_PHY_ID_UNSPEC,
ETHTOOL_PHY_DOWNSHIFT,
+ ETHTOOL_PHY_FAST_LINK_DOWN,
+ ETHTOOL_PHY_EDPD,
/*
* Add your fresh new phy tunable attribute above and remember to update
* phy_tunable_strings[] in net/ethtool/common.c
@@ -553,6 +579,76 @@
__u32 tx_pause;
};
+/**
+ * enum ethtool_link_ext_state - link extended state
+ */
+enum ethtool_link_ext_state {
+ ETHTOOL_LINK_EXT_STATE_AUTONEG,
+ ETHTOOL_LINK_EXT_STATE_LINK_TRAINING_FAILURE,
+ ETHTOOL_LINK_EXT_STATE_LINK_LOGICAL_MISMATCH,
+ ETHTOOL_LINK_EXT_STATE_BAD_SIGNAL_INTEGRITY,
+ ETHTOOL_LINK_EXT_STATE_NO_CABLE,
+ ETHTOOL_LINK_EXT_STATE_CABLE_ISSUE,
+ ETHTOOL_LINK_EXT_STATE_EEPROM_ISSUE,
+ ETHTOOL_LINK_EXT_STATE_CALIBRATION_FAILURE,
+ ETHTOOL_LINK_EXT_STATE_POWER_BUDGET_EXCEEDED,
+ ETHTOOL_LINK_EXT_STATE_OVERHEAT,
+};
+
+/**
+ * enum ethtool_link_ext_substate_autoneg - more information in addition to
+ * ETHTOOL_LINK_EXT_STATE_AUTONEG.
+ */
+enum ethtool_link_ext_substate_autoneg {
+ ETHTOOL_LINK_EXT_SUBSTATE_AN_NO_PARTNER_DETECTED = 1,
+ ETHTOOL_LINK_EXT_SUBSTATE_AN_ACK_NOT_RECEIVED,
+ ETHTOOL_LINK_EXT_SUBSTATE_AN_NEXT_PAGE_EXCHANGE_FAILED,
+ ETHTOOL_LINK_EXT_SUBSTATE_AN_NO_PARTNER_DETECTED_FORCE_MODE,
+ ETHTOOL_LINK_EXT_SUBSTATE_AN_FEC_MISMATCH_DURING_OVERRIDE,
+ ETHTOOL_LINK_EXT_SUBSTATE_AN_NO_HCD,
+};
+
+/**
+ * enum ethtool_link_ext_substate_link_training - more information in addition to
+ * ETHTOOL_LINK_EXT_STATE_LINK_TRAINING_FAILURE.
+ */
+enum ethtool_link_ext_substate_link_training {
+ ETHTOOL_LINK_EXT_SUBSTATE_LT_KR_FRAME_LOCK_NOT_ACQUIRED = 1,
+ ETHTOOL_LINK_EXT_SUBSTATE_LT_KR_LINK_INHIBIT_TIMEOUT,
+ ETHTOOL_LINK_EXT_SUBSTATE_LT_KR_LINK_PARTNER_DID_NOT_SET_RECEIVER_READY,
+ ETHTOOL_LINK_EXT_SUBSTATE_LT_REMOTE_FAULT,
+};
+
+/**
+ * enum ethtool_link_ext_substate_logical_mismatch - more information in addition
+ * to ETHTOOL_LINK_EXT_STATE_LINK_LOGICAL_MISMATCH.
+ */
+enum ethtool_link_ext_substate_link_logical_mismatch {
+ ETHTOOL_LINK_EXT_SUBSTATE_LLM_PCS_DID_NOT_ACQUIRE_BLOCK_LOCK = 1,
+ ETHTOOL_LINK_EXT_SUBSTATE_LLM_PCS_DID_NOT_ACQUIRE_AM_LOCK,
+ ETHTOOL_LINK_EXT_SUBSTATE_LLM_PCS_DID_NOT_GET_ALIGN_STATUS,
+ ETHTOOL_LINK_EXT_SUBSTATE_LLM_FC_FEC_IS_NOT_LOCKED,
+ ETHTOOL_LINK_EXT_SUBSTATE_LLM_RS_FEC_IS_NOT_LOCKED,
+};
+
+/**
+ * enum ethtool_link_ext_substate_bad_signal_integrity - more information in
+ * addition to ETHTOOL_LINK_EXT_STATE_BAD_SIGNAL_INTEGRITY.
+ */
+enum ethtool_link_ext_substate_bad_signal_integrity {
+ ETHTOOL_LINK_EXT_SUBSTATE_BSI_LARGE_NUMBER_OF_PHYSICAL_ERRORS = 1,
+ ETHTOOL_LINK_EXT_SUBSTATE_BSI_UNSUPPORTED_RATE,
+};
+
+/**
+ * enum ethtool_link_ext_substate_cable_issue - more information in
+ * addition to ETHTOOL_LINK_EXT_STATE_CABLE_ISSUE.
+ */
+enum ethtool_link_ext_substate_cable_issue {
+ ETHTOOL_LINK_EXT_SUBSTATE_CI_UNSUPPORTED_CABLE = 1,
+ ETHTOOL_LINK_EXT_SUBSTATE_CI_CABLE_TEST_FAILURE,
+};
+
#define ETH_GSTRING_LEN 32
/**
@@ -567,6 +663,13 @@
* @ETH_SS_RSS_HASH_FUNCS: RSS hush function names
* @ETH_SS_PHY_STATS: Statistic names, for use with %ETHTOOL_GPHYSTATS
* @ETH_SS_PHY_TUNABLES: PHY tunable names
+ * @ETH_SS_LINK_MODES: link mode names
+ * @ETH_SS_MSG_CLASSES: debug message class names
+ * @ETH_SS_WOL_MODES: wake-on-lan modes
+ * @ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags
+ * @ETH_SS_TS_TX_TYPES: timestamping Tx types
+ * @ETH_SS_TS_RX_FILTERS: timestamping Rx filters
+ * @ETH_SS_UDP_TUNNEL_TYPES: UDP tunnel types
*/
enum ethtool_stringset {
ETH_SS_TEST = 0,
@@ -578,6 +681,16 @@
ETH_SS_TUNABLES,
ETH_SS_PHY_STATS,
ETH_SS_PHY_TUNABLES,
+ ETH_SS_LINK_MODES,
+ ETH_SS_MSG_CLASSES,
+ ETH_SS_WOL_MODES,
+ ETH_SS_SOF_TIMESTAMPING,
+ ETH_SS_TS_TX_TYPES,
+ ETH_SS_TS_RX_FILTERS,
+ ETH_SS_UDP_TUNNEL_TYPES,
+
+ /* add new constants above here */
+ ETH_SS_COUNT
};
/**
@@ -886,7 +999,7 @@
__u32 location;
};
-/* How rings are layed out when accessing virtual functions or
+/* How rings are laid out when accessing virtual functions or
* offloaded queues is device specific. To allow users to do flow
* steering and specify these queues the ring cookie is partitioned
* into a 32bit queue index with an 8 bit virtual function id.
@@ -895,7 +1008,7 @@
* devices start supporting PCIe w/ARI. However at the moment I
* do not know of any devices that support this so I do not reserve
* space for this at this time. If a future patch consumes the next
- * byte it should be aware of this possiblity.
+ * byte it should be aware of this possibility.
*/
#define ETHTOOL_RX_FLOW_SPEC_RING 0x00000000FFFFFFFFLL
#define ETHTOOL_RX_FLOW_SPEC_RING_VF 0x000000FF00000000LL
@@ -1295,6 +1408,7 @@
ETHTOOL_FEC_OFF_BIT,
ETHTOOL_FEC_RS_BIT,
ETHTOOL_FEC_BASER_BIT,
+ ETHTOOL_FEC_LLRS_BIT,
};
#define ETHTOOL_FEC_NONE (1 << ETHTOOL_FEC_NONE_BIT)
@@ -1302,6 +1416,7 @@
#define ETHTOOL_FEC_OFF (1 << ETHTOOL_FEC_OFF_BIT)
#define ETHTOOL_FEC_RS (1 << ETHTOOL_FEC_RS_BIT)
#define ETHTOOL_FEC_BASER (1 << ETHTOOL_FEC_BASER_BIT)
+#define ETHTOOL_FEC_LLRS (1 << ETHTOOL_FEC_LLRS_BIT)
/* CMDs currently supported */
#define ETHTOOL_GSET 0x00000001 /* DEPRECATED, Get settings.
@@ -1436,6 +1551,13 @@
ETHTOOL_LINK_MODE_56000baseSR4_Full_BIT = 29,
ETHTOOL_LINK_MODE_56000baseLR4_Full_BIT = 30,
ETHTOOL_LINK_MODE_25000baseCR_Full_BIT = 31,
+
+ /* Last allowed bit for __ETHTOOL_LINK_MODE_LEGACY_MASK is bit
+ * 31. Please do NOT define any SUPPORTED_* or ADVERTISED_*
+ * macro for bits > 31. The only way to use indices > 31 is to
+ * use the new ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API.
+ */
+
ETHTOOL_LINK_MODE_25000baseKR_Full_BIT = 32,
ETHTOOL_LINK_MODE_25000baseSR_Full_BIT = 33,
ETHTOOL_LINK_MODE_50000baseCR2_Full_BIT = 34,
@@ -1457,15 +1579,48 @@
ETHTOOL_LINK_MODE_FEC_NONE_BIT = 49,
ETHTOOL_LINK_MODE_FEC_RS_BIT = 50,
ETHTOOL_LINK_MODE_FEC_BASER_BIT = 51,
-
- /* Last allowed bit for __ETHTOOL_LINK_MODE_LEGACY_MASK is bit
- * 31. Please do NOT define any SUPPORTED_* or ADVERTISED_*
- * macro for bits > 31. The only way to use indices > 31 is to
- * use the new ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API.
- */
-
- __ETHTOOL_LINK_MODE_LAST
- = ETHTOOL_LINK_MODE_FEC_BASER_BIT,
+ ETHTOOL_LINK_MODE_50000baseKR_Full_BIT = 52,
+ ETHTOOL_LINK_MODE_50000baseSR_Full_BIT = 53,
+ ETHTOOL_LINK_MODE_50000baseCR_Full_BIT = 54,
+ ETHTOOL_LINK_MODE_50000baseLR_ER_FR_Full_BIT = 55,
+ ETHTOOL_LINK_MODE_50000baseDR_Full_BIT = 56,
+ ETHTOOL_LINK_MODE_100000baseKR2_Full_BIT = 57,
+ ETHTOOL_LINK_MODE_100000baseSR2_Full_BIT = 58,
+ ETHTOOL_LINK_MODE_100000baseCR2_Full_BIT = 59,
+ ETHTOOL_LINK_MODE_100000baseLR2_ER2_FR2_Full_BIT = 60,
+ ETHTOOL_LINK_MODE_100000baseDR2_Full_BIT = 61,
+ ETHTOOL_LINK_MODE_200000baseKR4_Full_BIT = 62,
+ ETHTOOL_LINK_MODE_200000baseSR4_Full_BIT = 63,
+ ETHTOOL_LINK_MODE_200000baseLR4_ER4_FR4_Full_BIT = 64,
+ ETHTOOL_LINK_MODE_200000baseDR4_Full_BIT = 65,
+ ETHTOOL_LINK_MODE_200000baseCR4_Full_BIT = 66,
+ ETHTOOL_LINK_MODE_100baseT1_Full_BIT = 67,
+ ETHTOOL_LINK_MODE_1000baseT1_Full_BIT = 68,
+ ETHTOOL_LINK_MODE_400000baseKR8_Full_BIT = 69,
+ ETHTOOL_LINK_MODE_400000baseSR8_Full_BIT = 70,
+ ETHTOOL_LINK_MODE_400000baseLR8_ER8_FR8_Full_BIT = 71,
+ ETHTOOL_LINK_MODE_400000baseDR8_Full_BIT = 72,
+ ETHTOOL_LINK_MODE_400000baseCR8_Full_BIT = 73,
+ ETHTOOL_LINK_MODE_FEC_LLRS_BIT = 74,
+ ETHTOOL_LINK_MODE_100000baseKR_Full_BIT = 75,
+ ETHTOOL_LINK_MODE_100000baseSR_Full_BIT = 76,
+ ETHTOOL_LINK_MODE_100000baseLR_ER_FR_Full_BIT = 77,
+ ETHTOOL_LINK_MODE_100000baseCR_Full_BIT = 78,
+ ETHTOOL_LINK_MODE_100000baseDR_Full_BIT = 79,
+ ETHTOOL_LINK_MODE_200000baseKR2_Full_BIT = 80,
+ ETHTOOL_LINK_MODE_200000baseSR2_Full_BIT = 81,
+ ETHTOOL_LINK_MODE_200000baseLR2_ER2_FR2_Full_BIT = 82,
+ ETHTOOL_LINK_MODE_200000baseDR2_Full_BIT = 83,
+ ETHTOOL_LINK_MODE_200000baseCR2_Full_BIT = 84,
+ ETHTOOL_LINK_MODE_400000baseKR4_Full_BIT = 85,
+ ETHTOOL_LINK_MODE_400000baseSR4_Full_BIT = 86,
+ ETHTOOL_LINK_MODE_400000baseLR4_ER4_FR4_Full_BIT = 87,
+ ETHTOOL_LINK_MODE_400000baseDR4_Full_BIT = 88,
+ ETHTOOL_LINK_MODE_400000baseCR4_Full_BIT = 89,
+ ETHTOOL_LINK_MODE_100baseFX_Half_BIT = 90,
+ ETHTOOL_LINK_MODE_100baseFX_Full_BIT = 91,
+ /* must be last entry */
+ __ETHTOOL_LINK_MODE_MASK_NBITS
};
#define __ETHTOOL_LINK_MODE_LEGACY_MASK(base_name) \
@@ -1573,12 +1728,14 @@
#define SPEED_50000 50000
#define SPEED_56000 56000
#define SPEED_100000 100000
+#define SPEED_200000 200000
+#define SPEED_400000 400000
#define SPEED_UNKNOWN -1
static inline int ethtool_validate_speed(__u32 speed)
{
- return speed <= INT_MAX || speed == SPEED_UNKNOWN;
+ return speed <= INT_MAX || speed == (__u32)SPEED_UNKNOWN;
}
/* Duplex, half or full. */
@@ -1597,6 +1754,18 @@
return 0;
}
+
+#define MASTER_SLAVE_CFG_UNSUPPORTED 0
+#define MASTER_SLAVE_CFG_UNKNOWN 1
+#define MASTER_SLAVE_CFG_MASTER_PREFERRED 2
+#define MASTER_SLAVE_CFG_SLAVE_PREFERRED 3
+#define MASTER_SLAVE_CFG_MASTER_FORCE 4
+#define MASTER_SLAVE_CFG_SLAVE_FORCE 5
+#define MASTER_SLAVE_STATE_UNSUPPORTED 0
+#define MASTER_SLAVE_STATE_UNKNOWN 1
+#define MASTER_SLAVE_STATE_MASTER 2
+#define MASTER_SLAVE_STATE_SLAVE 3
+#define MASTER_SLAVE_STATE_ERR 4
/* Which connector port. */
#define PORT_TP 0x00
@@ -1636,6 +1805,8 @@
#define WAKE_MAGIC (1 << 5)
#define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */
#define WAKE_FILTER (1 << 7)
+
+#define WOL_MODE_COUNT 8
/* L2-L4 network traffic flow types */
#define TCP_V4_FLOW 0x01 /* hash or spec (tcp_ip4_spec) */
@@ -1690,6 +1861,9 @@
#define ETH_MODULE_SFF_8636_LEN 256
#define ETH_MODULE_SFF_8436 0x4
#define ETH_MODULE_SFF_8436_LEN 256
+
+#define ETH_MODULE_SFF_8636_MAX_LEN 640
+#define ETH_MODULE_SFF_8436_MAX_LEN 640
/* Reset flags */
/* The reset() operation must clear the flags for the components which
@@ -1800,14 +1974,9 @@
* rejected.
*
* Deprecated %ethtool_cmd fields transceiver, maxtxpkt and maxrxpkt
- * are not available in %ethtool_link_settings. Until all drivers are
- * converted to ignore them or to the new %ethtool_link_settings API,
- * for both queries and changes, users should always try
- * %ETHTOOL_GLINKSETTINGS first, and if it fails with -ENOTSUPP stick
- * only to %ETHTOOL_GSET and %ETHTOOL_SSET consistently. If it
- * succeeds, then users should stick to %ETHTOOL_GLINKSETTINGS and
- * %ETHTOOL_SLINKSETTINGS (which would support drivers implementing
- * either %ethtool_cmd or %ethtool_link_settings).
+ * are not available in %ethtool_link_settings. These fields will be
+ * always set to zero in %ETHTOOL_GSET reply and %ETHTOOL_SSET will
+ * fail if any of them is set to non-zero value.
*
* Users should assume that all fields not marked read-only are
* writable and subject to validation by the driver. They should use
@@ -1836,7 +2005,9 @@
__u8 eth_tp_mdix_ctrl;
__s8 link_mode_masks_nwords;
__u8 transceiver;
- __u8 reserved1[3];
+ __u8 master_slave_cfg;
+ __u8 master_slave_state;
+ __u8 reserved1[1];
__u32 reserved[7];
__u32 link_mode_masks[0];
/* layout of link_mode_masks fields:
--
Gitblit v1.6.2