From cde9070d9970eef1f7ec2360586c802a16230ad8 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Fri, 10 May 2024 07:43:50 +0000
Subject: [PATCH] rtl88x2CE_WiFi_linux driver
---
kernel/drivers/tty/serial/8250/8250_fintek.c | 46 ++++++++++++++++++----------------------------
1 files changed, 18 insertions(+), 28 deletions(-)
diff --git a/kernel/drivers/tty/serial/8250/8250_fintek.c b/kernel/drivers/tty/serial/8250/8250_fintek.c
index 79a4958..dba5950 100644
--- a/kernel/drivers/tty/serial/8250/8250_fintek.c
+++ b/kernel/drivers/tty/serial/8250/8250_fintek.c
@@ -19,6 +19,7 @@
#define CHIP_ID2 0x21
#define CHIP_ID_F81865 0x0407
#define CHIP_ID_F81866 0x1010
+#define CHIP_ID_F81966 0x0215
#define CHIP_ID_F81216AD 0x1602
#define CHIP_ID_F81216H 0x0501
#define CHIP_ID_F81216 0x0802
@@ -62,9 +63,9 @@
#define F81216_LDN_HIGH 0x4
/*
- * F81866 registers
+ * F81866/966 registers
*
- * The IRQ setting mode of F81866 is not the same with F81216 series.
+ * The IRQ setting mode of F81866/966 is not the same with F81216 series.
* Level/Low: IRQ_MODE0:0, IRQ_MODE1:0
* Edge/High: IRQ_MODE0:1, IRQ_MODE1:0
*
@@ -155,6 +156,7 @@
switch (chip) {
case CHIP_ID_F81865:
case CHIP_ID_F81866:
+ case CHIP_ID_F81966:
case CHIP_ID_F81216AD:
case CHIP_ID_F81216H:
case CHIP_ID_F81216:
@@ -171,6 +173,7 @@
int *max)
{
switch (pdata->pid) {
+ case CHIP_ID_F81966:
case CHIP_ID_F81865:
case CHIP_ID_F81866:
*min = F81866_LDN_LOW;
@@ -197,12 +200,12 @@
if (!pdata)
return -EINVAL;
- /* Hardware do not support same RTS level on send and receive */
- if (!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
- !(rs485->flags & SER_RS485_RTS_AFTER_SEND))
- return -EINVAL;
if (rs485->flags & SER_RS485_ENABLED) {
+ /* Hardware do not support same RTS level on send and receive */
+ if (!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
+ !(rs485->flags & SER_RS485_RTS_AFTER_SEND))
+ return -EINVAL;
memset(rs485->padding, 0, sizeof(rs485->padding));
config |= RS485_URA;
} else {
@@ -248,10 +251,11 @@
sio_write_reg(pdata, LDN, pdata->index);
switch (pdata->pid) {
+ case CHIP_ID_F81966:
case CHIP_ID_F81866:
sio_write_mask_reg(pdata, F81866_FIFO_CTRL, F81866_IRQ_MODE1,
0);
- /* fall through */
+ fallthrough;
case CHIP_ID_F81865:
sio_write_mask_reg(pdata, F81866_IRQ_MODE, F81866_IRQ_SHARE,
F81866_IRQ_SHARE);
@@ -274,6 +278,7 @@
{
switch (pdata->pid) {
case CHIP_ID_F81216H: /* 128Bytes FIFO */
+ case CHIP_ID_F81966:
case CHIP_ID_F81866:
sio_write_mask_reg(pdata, FIFO_CTRL,
FIFO_MODE_MASK | RXFTHR_MODE_MASK,
@@ -285,26 +290,9 @@
}
}
-static void fintek_8250_goto_highspeed(struct uart_8250_port *uart,
- struct fintek_8250 *pdata)
-{
- sio_write_reg(pdata, LDN, pdata->index);
-
- switch (pdata->pid) {
- case CHIP_ID_F81866: /* set uart clock for high speed serial mode */
- sio_write_mask_reg(pdata, F81866_UART_CLK,
- F81866_UART_CLK_MASK,
- F81866_UART_CLK_14_769MHZ);
-
- uart->port.uartclk = 921600 * 16;
- break;
- default: /* leave clock speed untouched */
- break;
- }
-}
-
-void fintek_8250_set_termios(struct uart_port *port, struct ktermios *termios,
- struct ktermios *old)
+static void fintek_8250_set_termios(struct uart_port *port,
+ struct ktermios *termios,
+ struct ktermios *old)
{
struct fintek_8250 *pdata = port->private_data;
unsigned int baud = tty_termios_baud_rate(termios);
@@ -326,6 +314,7 @@
case CHIP_ID_F81216H:
reg = RS485;
break;
+ case CHIP_ID_F81966:
case CHIP_ID_F81866:
reg = F81866_UART_CLK;
break;
@@ -372,6 +361,7 @@
switch (pdata->pid) {
case CHIP_ID_F81216H:
+ case CHIP_ID_F81966:
case CHIP_ID_F81866:
uart->port.set_termios = fintek_8250_set_termios;
break;
@@ -421,7 +411,6 @@
fintek_8250_set_irq_mode(pdata, level_mode);
fintek_8250_set_max_fifo(pdata);
- fintek_8250_goto_highspeed(uart, pdata);
fintek_8250_exit_key(addr[i]);
@@ -442,6 +431,7 @@
switch (pdata->pid) {
case CHIP_ID_F81216AD:
case CHIP_ID_F81216H:
+ case CHIP_ID_F81966:
case CHIP_ID_F81866:
case CHIP_ID_F81865:
uart->port.rs485_config = fintek_8250_rs485_config;
--
Gitblit v1.6.2