From a36159eec6ca17402b0e146b86efaf76568dc353 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Fri, 20 Sep 2024 01:41:23 +0000
Subject: [PATCH] 重命名 AX88772C_eeprom/asix.c 为 asix_mac.c
---
kernel/arch/mips/cavium-octeon/executive/cvmx-helper-board.c | 90 +++-----------------------------------------
1 files changed, 7 insertions(+), 83 deletions(-)
diff --git a/kernel/arch/mips/cavium-octeon/executive/cvmx-helper-board.c b/kernel/arch/mips/cavium-octeon/executive/cvmx-helper-board.c
index ab8362e..9b791cc 100644
--- a/kernel/arch/mips/cavium-octeon/executive/cvmx-helper-board.c
+++ b/kernel/arch/mips/cavium-octeon/executive/cvmx-helper-board.c
@@ -31,6 +31,7 @@
* network ports from the rest of the cvmx-helper files.
*/
+#include <linux/bug.h>
#include <asm/octeon/octeon.h>
#include <asm/octeon/cvmx-bootinfo.h>
@@ -206,60 +207,22 @@
* Returns The ports link status. If the link isn't fully resolved, this must
* return zero.
*/
-cvmx_helper_link_info_t __cvmx_helper_board_link_get(int ipd_port)
+union cvmx_helper_link_info __cvmx_helper_board_link_get(int ipd_port)
{
- cvmx_helper_link_info_t result;
+ union cvmx_helper_link_info result;
+
+ WARN_ONCE(!octeon_is_simulation(),
+ "Using deprecated link status - please update your DT");
/* Unless we fix it later, all links are defaulted to down */
result.u64 = 0;
- /*
- * This switch statement should handle all ports that either don't use
- * Marvell PHYS, or don't support in-band status.
- */
- switch (cvmx_sysinfo_get()->board_type) {
- case CVMX_BOARD_TYPE_SIM:
+ if (octeon_is_simulation()) {
/* The simulator gives you a simulated 1Gbps full duplex link */
result.s.link_up = 1;
result.s.full_duplex = 1;
result.s.speed = 1000;
return result;
- case CVMX_BOARD_TYPE_EBH3100:
- case CVMX_BOARD_TYPE_CN3010_EVB_HS5:
- case CVMX_BOARD_TYPE_CN3005_EVB_HS5:
- case CVMX_BOARD_TYPE_CN3020_EVB_HS5:
- /* Port 1 on these boards is always Gigabit */
- if (ipd_port == 1) {
- result.s.link_up = 1;
- result.s.full_duplex = 1;
- result.s.speed = 1000;
- return result;
- }
- /* Fall through to the generic code below */
- break;
- case CVMX_BOARD_TYPE_CUST_NB5:
- /* Port 1 on these boards is always Gigabit */
- if (ipd_port == 1) {
- result.s.link_up = 1;
- result.s.full_duplex = 1;
- result.s.speed = 1000;
- return result;
- }
- break;
- case CVMX_BOARD_TYPE_BBGW_REF:
- /* Port 1 on these boards is always Gigabit */
- if (ipd_port == 2) {
- /* Port 2 is not hooked up */
- result.u64 = 0;
- return result;
- } else {
- /* Ports 0 and 1 connect to the switch */
- result.s.link_up = 1;
- result.s.full_duplex = 1;
- result.s.speed = 1000;
- return result;
- }
- break;
}
if (OCTEON_IS_MODEL(OCTEON_CN3XXX)
@@ -355,45 +318,6 @@
break;
}
return supported_ports;
-}
-
-/**
- * Enable packet input/output from the hardware. This function is
- * called after by cvmx_helper_packet_hardware_enable() to
- * perform board specific initialization. For most boards
- * nothing is needed.
- *
- * @interface: Interface to enable
- *
- * Returns Zero on success, negative on failure
- */
-int __cvmx_helper_board_hardware_enable(int interface)
-{
- if (cvmx_sysinfo_get()->board_type == CVMX_BOARD_TYPE_CN3005_EVB_HS5) {
- if (interface == 0) {
- /* Different config for switch port */
- cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(1, interface), 0);
- cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(1, interface), 0);
- /*
- * Boards with gigabit WAN ports need a
- * different setting that is compatible with
- * 100 Mbit settings
- */
- cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(0, interface),
- 0xc);
- cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(0, interface),
- 0xc);
- }
- } else if (cvmx_sysinfo_get()->board_type ==
- CVMX_BOARD_TYPE_UBNT_E100) {
- cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(0, interface), 0);
- cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(0, interface), 0x10);
- cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(1, interface), 0);
- cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(1, interface), 0x10);
- cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(2, interface), 0);
- cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(2, interface), 0x10);
- }
- return 0;
}
/**
--
Gitblit v1.6.2