From a36159eec6ca17402b0e146b86efaf76568dc353 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Fri, 20 Sep 2024 01:41:23 +0000
Subject: [PATCH] 重命名 AX88772C_eeprom/asix.c 为 asix_mac.c
---
kernel/arch/arm64/boot/dts/rockchip/NK-R36S0.dtsi | 274 ++++++++++++++++++++++++++++++++++++++++++++----------
1 files changed, 222 insertions(+), 52 deletions(-)
diff --git a/kernel/arch/arm64/boot/dts/rockchip/NK-R36S0.dtsi b/kernel/arch/arm64/boot/dts/rockchip/NK-R36S0.dtsi
index 487f484..61008c7 100755
--- a/kernel/arch/arm64/boot/dts/rockchip/NK-R36S0.dtsi
+++ b/kernel/arch/arm64/boot/dts/rockchip/NK-R36S0.dtsi
@@ -19,6 +19,7 @@
rk_headset: rk-headset {
compatible = "rockchip_headset";
headset_gpio = <&gpio0 RK_PD5 GPIO_ACTIVE_LOW>;
+ spk_ctl_gpio = <&gpio4 RK_PC2 GPIO_ACTIVE_LOW>;//AMP_SD_GPIO4_C2_3V3
pinctrl-names = "default";
pinctrl-0 = <&hp_det>;
};
@@ -89,9 +90,135 @@
};
#endif
+ leds: leds {
+ compatible = "gpio-leds";
+ sig_led: sig_led {
+ gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+ err_led: err_led {
+ gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+
+ ndj_io_init {
+ compatible = "nk_io_control";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nk_io_gpio>;
+
+ //gpio_op0 = <&gpio1 RK_PD0 GPIO_ACTIVE_HIGH>;
+
+ vcc_5v {
+ gpio_num = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; //VCC5_IO_EN_GPIO1_A4_3V3
+ gpio_function = <0>;
+ };
+
+ vcc_12v {
+ gpio_num = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>; //VCC12_IO_EN_GPIO0_C7_3V3
+ gpio_function = <0>;
+ };
+
+ vcc_3.3v {
+ gpio_num = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>; //VCC3_IO_EN_GPIO0_C4_3V3
+ gpio_function = <0>;
+ };
+
+ ax88772_rst {
+ gpio_num = <&gpio3 RK_PB5 GPIO_ACTIVE_HIGH>; //AX88772_RST_GPIO3_B5_3V3
+ gpio_function = <3>;
+ };
+
+ ax88631_rst {
+ gpio_num = <&gpio3 RK_PB6 GPIO_ACTIVE_HIGH>; //AX88772_RST_GPIO3_B6_3V3
+ gpio_function = <3>;
+ };
+
+ hub_host3 {
+ gpio_num = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>; //HOST3_EN_GPIO4_B2_1V8
+ gpio_function = <0>;
+ };
+
+ wake_4g {
+ gpio_num = <&gpio1 RK_PB1 GPIO_ACTIVE_LOW>; //4G_WAKEUP_GPIO01_B1_3V3
+ gpio_function = <0>;
+ };
+
+ air_mode_4g {
+ gpio_num = <&gpio1 RK_PB0 GPIO_ACTIVE_LOW>; //4G_AIR_MODE_GPIO01_B0_3V3
+ gpio_function = <0>;
+ };
+
+ reset_4g {
+ gpio_num = <&gpio1 RK_PB2 GPIO_ACTIVE_LOW>; //4G_RST_GPIO01_B2_3V3
+ gpio_function = <3>;
+ };
+
+ en_4g {
+ gpio_num = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>; //4G_PWREN_H_GPIO0_C6
+ gpio_function = <0>;
+ };
+
+ //gpio99 {
+ // gpio_num = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;//HP_EN_GPIO3_A6_3V3
+ // gpio_function = <1>;
+ //};
+
+ wifi_power_en {
+ gpio_num = <&gpio3 RK_PC6 GPIO_ACTIVE_HIGH>; //WIFI_PWREN_GPIO3_C6_1V8
+ gpio_function = <0>;
+ };
+ #if 0
+ do1 {
+ gpio_num = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>;
+ gpio_function = <0>;
+ };
+
+ do2 {
+ gpio_num = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
+ gpio_function = <0>;
+ };
+
+ do3 {
+ gpio_num = <&gpio1 RK_PD1 GPIO_ACTIVE_HIGH>;
+ gpio_function = <0>;
+ };
+
+ do4 {
+ gpio_num = <&gpio1 RK_PD3 GPIO_ACTIVE_HIGH>;
+ gpio_function = <0>;
+ };
+
+ do5 {
+ gpio_num = <&gpio2 RK_PD6 GPIO_ACTIVE_LOW>;
+ gpio_function = <0>;
+ };
+
+ do6 {
+ gpio_num = <&gpio2 RK_PD7 GPIO_ACTIVE_LOW>;
+ gpio_function = <0>;
+ };
+
+ do7 {
+ gpio_num = <&gpio3 RK_PA0 GPIO_ACTIVE_LOW>;
+ gpio_function = <0>;
+ };
+
+ di1 {
+ gpio_num = <&gpio2 RK_PD5 GPIO_ACTIVE_HIGH>;
+ gpio_function = <1>;
+ };
+ #endif
+ };
+#if 0
nk_io_init {
compatible = "nk_io_control";
- vcc3_io_en_gpio = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>; //VCC3_IO_EN_GPIO0_C4_3V3
+// vcc3_io_en_gpio = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>; //VCC3_IO_EN_GPIO0_C4_3V3
hub_host2_5V_rest_gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; //HUB_RST_GPIO4_D2_3V3
hub_host3_5v_gpio = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>; //HOST3_EN_GPIO4_B2_1V8
vcc_5v_io = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; //VCC5_IO_EN_GPIO1_A4_3V3
@@ -101,13 +228,13 @@
air_mode_4g_gpio = <&gpio1 RK_PB0 GPIO_ACTIVE_HIGH>; //4G_AIR_MODE_GPIO01_B0_3V3
wake_4g_gpio = <&gpio1 RK_PB1 GPIO_ACTIVE_HIGH>; //4G_WAKEUP_GPIO01_B1_3V3
hp_en_gpio = <&gpio3 RK_PA6 GPIO_ACTIVE_HIGH>;//HP_EN_GPIO3_A6_3V3
- spk_out_gpio = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;//AMP_SD_GPIO4_C2_3V3
+// spk_out_gpio = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;//AMP_SD_GPIO4_C2_3V3
wifi_power_en_gpio = <&gpio3 RK_PC6 GPIO_ACTIVE_HIGH>; //WIFI_PWREN_GPIO3_C6_1V8
// pcie_power_en_gpio = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;//PCIE_PWREN_H_GPIO0_D4
pinctrl-names = "default";
pinctrl-0 = <&nk_io_gpio>;
};
-
+#endif
panel: panel {
compatible = "simple-panel";
backlight = <&backlight>;
@@ -127,8 +254,8 @@
nodka-lvds = <15>;
display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
+ native-mode = <&timing>;
+ timing: timing {
clock-frequency = <72500000>;
hactive = <1280>;
vactive = <800>;
@@ -145,8 +272,8 @@
};
};
ports {
- panel_in: endpoint {
- remote-endpoint = <&edp_out>;
+ panel_in_lvds: endpoint {
+ remote-endpoint = <&lvds_out>;
};
};
};
@@ -253,8 +380,19 @@
};
&dsi1_panel {
- power-supply = <&vcc3v3_lcd1_n>;
+// power-supply = <&vcc3v3_lcd1_n>; //MIPI_3V3EN_GPIO3_A3_d_3V3
+ vddio-mipi = <&gpio3 RK_PA4 GPIO_ACTIVE_HIGH>; //MIPI_EN_1V8_GPIO3_A4_d_3V3
+ reset-gpios = <&gpio3 RK_PC7 GPIO_ACTIVE_LOW>; //MIPI_RST_L_GPIO3_C7
+ vcc-5v-gpio = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; //VCC5_IO_EN_GPIO1_A4_3V3
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd1_rst_gpio>;
};
+
+&route_dsi1 {
+ status = "disabled";
+ connect = <&vp1_out_dsi1>;
+};
+
/*
* edp_start
@@ -262,19 +400,11 @@
&edp {
force-hpd;
- status = "okay";
- ports {
- port@1 {
- reg = <1>;
- edp_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
+ status = "disabled";
};
&edp_phy {
- status = "okay";
+ status = "disabled";
};
&edp_in_vp0 {
@@ -282,17 +412,40 @@
};
&edp_in_vp1 {
- status = "okay";
+ status = "disabled";
+
};
&route_edp {
- status = "okay";
+ status = "disabled";
connect = <&vp1_out_edp>;
};
&route_edp {
- status = "okay";
+ status = "disabled";
};
+
+&lvds {
+ status = "disabled";
+ ports {
+ port@1 {
+ reg = <1>;
+ lvds_out:endpoint {
+ remote-endpoint = <&panel_in_lvds>;
+ };
+ };
+ };
+};
+
+&route_lvds{
+ status = "okay";
+ connect = <&vp1_out_lvds>;
+};
+
+&lvds_in_vp1 {
+ status = "disabled";
+};
+
/*
* edp_end
*/
@@ -337,7 +490,7 @@
phy-mode = "rgmii";
clock_in_out = "output";
- snps,reset-gpio = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
+ snps,reset-gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>;
snps,reset-active-low;
/* Reset time is 20ms, 100ms for rtl8211f */
snps,reset-delays-us = <0 20000 100000>;
@@ -357,7 +510,9 @@
rx_delay = <0x2f>;
phy-handle = <&rgmii_phy0>;
+
status = "disabled";
+
};
&gmac1 {
@@ -391,9 +546,7 @@
* power-supply should switche to vcc3v3_lcd1_n
* when mipi panel is connected to dsi1.
*/
->1x {
- power-supply = <&vcc3v3_lcd0_n>;
-};
+
&i2c3 {
status = "okay";
@@ -412,7 +565,7 @@
};
&i2c4 {
- status = "okay";
+ status = "disabled";
gc8034: gc8034@37 {
compatible = "galaxycore,gc8034";
status = "okay";
@@ -424,7 +577,6 @@
reset-gpios = <&gpio3 RK_PB6 GPIO_ACTIVE_LOW>;
pwdn-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_LOW>;
rockchip,grf = <&grf>;
- power-domains = <&power RK3568_PD_VI>;
rockchip,camera-module-index = <0>;
rockchip,camera-module-facing = "back";
rockchip,camera-module-name = "RK-CMK-8M-2-v1";
@@ -458,7 +610,7 @@
};
};
ov5695: ov5695@36 {
- status = "okay";
+ status = "disabled";
compatible = "ovti,ov5695";
reg = <0x36>;
clocks = <&cru CLK_CIF_OUT>;
@@ -511,7 +663,7 @@
&pcie30phy {
- status = "okay";
+ status = "disabled";
};
&pcie2x1 {
@@ -530,7 +682,8 @@
// };
headphone {
hp_det: hp-det {
- rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_down>;
+ rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_down>,
+ <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
@@ -545,6 +698,13 @@
rockchip,pins = <2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
+
+ lcd1 {
+ lcd1_rst_gpio: lcd1-rst-gpio {
+ rockchip,pins = <3 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
nk_io_init{
nk_io_gpio: nk-io-gpio{
rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>,
@@ -558,12 +718,25 @@
<1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>,
<1 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>,
<3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>,
- <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>,
<3 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>,
<3 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>,
<3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>,
<3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>,
+ <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>,
+ <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>,
+ <3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>,
<3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>,
+ <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_B0_u_3V3 DO1 8
+ <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_B3_u_3V3 DO2 11
+ <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_B4_u_3V3 DO3 12
+ <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_B5_u_3V3 DO4 13
+ <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_B6_u_3V3 DO5 14
+
+ <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_C0_d_3V3 DI1 16
+ <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_C1_d_3V3 DI2 17
+ <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_C2_d_3V3 DI3 18
+ <0 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_C3_d_3V3 DI4 19
+ <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_C5_d_3V3 DI5 21
<0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
@@ -589,11 +762,6 @@
remote-endpoint = <&csidphy_out>;
};
};
-};
-
-&route_dsi0 {
- status = "disabled";
- connect = <&vp1_out_dsi0>;
};
@@ -634,15 +802,6 @@
pinctrl-0 = <&uart8m0_xfer &uart8m0_ctsn>;
};
-&vcc3v3_lcd0_n {
- gpio = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
-};
-
-&vcc3v3_lcd1_n {
- gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
- enable-active-high;
-};
&wireless_wlan {
pinctrl-names = "default";
@@ -656,18 +815,23 @@
clock-names = "ext_clock";
//wifi-bt-power-toggle;
uart_rts_gpios = <&gpio2 RK_PB5 GPIO_ACTIVE_LOW>;
- BT,power_gpio = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default", "rts_gpio";
pinctrl-0 = <&uart1m0_rtsn>;
pinctrl-1 = <&uart1_gpios>;
- BT,reset_gpio = <&gpio3 RK_PA0 GPIO_ACTIVE_HIGH>;
- BT,wake_gpio = <&gpio3 RK_PA2 GPIO_ACTIVE_HIGH>;
- BT,wake_host_irq = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
+ BT,reset_gpio = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+ BT,wake_gpio = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
+ BT,wake_host_irq = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
status = "disabled";
};
&uart0 {
- status = "okay";
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;
+ status = "disabled";
};
&uart3 {
@@ -676,7 +840,7 @@
};
&uart4 {
- status = "okay";
+ status = "disabled";
pinctrl-0 = <&uart4m1_xfer>;
};
@@ -685,12 +849,18 @@
pinctrl-0 = <&uart5m1_xfer>;
};
+
&uart7 {
status = "okay";
pinctrl-0 = <&uart7m1_xfer>;
};
+&uart8 {
+ status = "disabled";
+ pinctrl-0 = <&uart8m1_xfer>;
+};
+
&uart9 {
- status = "okay";
+ status = "disabled";
pinctrl-0 = <&uart9m1_xfer>;
};
--
Gitblit v1.6.2