From 9d77db3c730780c8ef5ccd4b66403ff5675cfe4e Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Mon, 13 May 2024 10:30:14 +0000
Subject: [PATCH] modify sin led gpio
---
kernel/drivers/mmc/host/sdhci-iproc.c | 123 ++++++++++++++++++++++++++++++++++------
1 files changed, 104 insertions(+), 19 deletions(-)
diff --git a/kernel/drivers/mmc/host/sdhci-iproc.c b/kernel/drivers/mmc/host/sdhci-iproc.c
index a533ba9..b9eb2ec 100644
--- a/kernel/drivers/mmc/host/sdhci-iproc.c
+++ b/kernel/drivers/mmc/host/sdhci-iproc.c
@@ -15,6 +15,7 @@
* iProc SDHCI platform driver
*/
+#include <linux/acpi.h>
#include <linux/delay.h>
#include <linux/module.h>
#include <linux/mmc/host.h>
@@ -162,9 +163,36 @@
sdhci_iproc_writel(host, newval, reg & ~3);
}
+static unsigned int sdhci_iproc_get_max_clock(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+ if (pltfm_host->clk)
+ return sdhci_pltfm_clk_get_max_clock(host);
+ else
+ return pltfm_host->clock;
+}
+
+/*
+ * There is a known bug on BCM2711's SDHCI core integration where the
+ * controller will hang when the difference between the core clock and the bus
+ * clock is too great. Specifically this can be reproduced under the following
+ * conditions:
+ *
+ * - No SD card plugged in, polling thread is running, probing cards at
+ * 100 kHz.
+ * - BCM2711's core clock configured at 500MHz or more
+ *
+ * So we set 200kHz as the minimum clock frequency available for that SoC.
+ */
+static unsigned int sdhci_iproc_bcm2711_get_min_clock(struct sdhci_host *host)
+{
+ return 200000;
+}
+
static const struct sdhci_ops sdhci_iproc_ops = {
.set_clock = sdhci_set_clock,
- .get_max_clock = sdhci_pltfm_clk_get_max_clock,
+ .get_max_clock = sdhci_iproc_get_max_clock,
.set_bus_width = sdhci_set_bus_width,
.reset = sdhci_reset,
.set_uhs_signaling = sdhci_set_uhs_signaling,
@@ -178,7 +206,7 @@
.write_w = sdhci_iproc_writew,
.write_b = sdhci_iproc_writeb,
.set_clock = sdhci_set_clock,
- .get_max_clock = sdhci_pltfm_clk_get_max_clock,
+ .get_max_clock = sdhci_iproc_get_max_clock,
.set_bus_width = sdhci_set_bus_width,
.reset = sdhci_reset,
.set_uhs_signaling = sdhci_set_uhs_signaling,
@@ -250,27 +278,80 @@
.mmc_caps = 0x00000000,
};
+static const struct sdhci_ops sdhci_iproc_bcm2711_ops = {
+ .read_l = sdhci_iproc_readl,
+ .read_w = sdhci_iproc_readw,
+ .read_b = sdhci_iproc_readb,
+ .write_l = sdhci_iproc_writel,
+ .write_w = sdhci_iproc_writew,
+ .write_b = sdhci_iproc_writeb,
+ .set_clock = sdhci_set_clock,
+ .set_power = sdhci_set_power_and_bus_voltage,
+ .get_max_clock = sdhci_iproc_get_max_clock,
+ .get_min_clock = sdhci_iproc_bcm2711_get_min_clock,
+ .set_bus_width = sdhci_set_bus_width,
+ .reset = sdhci_reset,
+ .set_uhs_signaling = sdhci_set_uhs_signaling,
+};
+
+static const struct sdhci_pltfm_data sdhci_bcm2711_pltfm_data = {
+ .quirks = SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12,
+ .ops = &sdhci_iproc_bcm2711_ops,
+};
+
+static const struct sdhci_iproc_data bcm2711_data = {
+ .pdata = &sdhci_bcm2711_pltfm_data,
+ .mmc_caps = MMC_CAP_3_3V_DDR,
+};
+
static const struct of_device_id sdhci_iproc_of_match[] = {
{ .compatible = "brcm,bcm2835-sdhci", .data = &bcm2835_data },
+ { .compatible = "brcm,bcm2711-emmc2", .data = &bcm2711_data },
{ .compatible = "brcm,sdhci-iproc-cygnus", .data = &iproc_cygnus_data},
{ .compatible = "brcm,sdhci-iproc", .data = &iproc_data },
{ }
};
MODULE_DEVICE_TABLE(of, sdhci_iproc_of_match);
+#ifdef CONFIG_ACPI
+/*
+ * This is a duplicate of bcm2835_(pltfrm_)data without caps quirks
+ * which are provided by the ACPI table.
+ */
+static const struct sdhci_pltfm_data sdhci_bcm_arasan_data = {
+ .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
+ SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK |
+ SDHCI_QUIRK_NO_HISPD_BIT,
+ .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
+ .ops = &sdhci_iproc_32only_ops,
+};
+
+static const struct sdhci_iproc_data bcm_arasan_data = {
+ .pdata = &sdhci_bcm_arasan_data,
+};
+
+static const struct acpi_device_id sdhci_iproc_acpi_ids[] = {
+ { .id = "BRCM5871", .driver_data = (kernel_ulong_t)&iproc_cygnus_data },
+ { .id = "BRCM5872", .driver_data = (kernel_ulong_t)&iproc_data },
+ { .id = "BCM2847", .driver_data = (kernel_ulong_t)&bcm_arasan_data },
+ { .id = "BRCME88C", .driver_data = (kernel_ulong_t)&bcm2711_data },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(acpi, sdhci_iproc_acpi_ids);
+#endif
+
static int sdhci_iproc_probe(struct platform_device *pdev)
{
- const struct of_device_id *match;
- const struct sdhci_iproc_data *iproc_data;
+ struct device *dev = &pdev->dev;
+ const struct sdhci_iproc_data *iproc_data = NULL;
struct sdhci_host *host;
struct sdhci_iproc_host *iproc_host;
struct sdhci_pltfm_host *pltfm_host;
int ret;
- match = of_match_device(sdhci_iproc_of_match, &pdev->dev);
- if (!match)
- return -EINVAL;
- iproc_data = match->data;
+ iproc_data = device_get_match_data(dev);
+ if (!iproc_data)
+ return -ENODEV;
host = sdhci_pltfm_init(pdev, iproc_data->pdata, sizeof(*iproc_host));
if (IS_ERR(host))
@@ -285,19 +366,21 @@
if (ret)
goto err;
- sdhci_get_of_property(pdev);
+ sdhci_get_property(pdev);
host->mmc->caps |= iproc_host->data->mmc_caps;
- pltfm_host->clk = devm_clk_get(&pdev->dev, NULL);
- if (IS_ERR(pltfm_host->clk)) {
- ret = PTR_ERR(pltfm_host->clk);
- goto err;
- }
- ret = clk_prepare_enable(pltfm_host->clk);
- if (ret) {
- dev_err(&pdev->dev, "failed to enable host clk\n");
- goto err;
+ if (dev->of_node) {
+ pltfm_host->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(pltfm_host->clk)) {
+ ret = PTR_ERR(pltfm_host->clk);
+ goto err;
+ }
+ ret = clk_prepare_enable(pltfm_host->clk);
+ if (ret) {
+ dev_err(dev, "failed to enable host clk\n");
+ goto err;
+ }
}
if (iproc_host->data->pdata->quirks & SDHCI_QUIRK_MISSING_CAPS) {
@@ -312,7 +395,8 @@
return 0;
err_clk:
- clk_disable_unprepare(pltfm_host->clk);
+ if (dev->of_node)
+ clk_disable_unprepare(pltfm_host->clk);
err:
sdhci_pltfm_free(pdev);
return ret;
@@ -323,6 +407,7 @@
.name = "sdhci-iproc",
.probe_type = PROBE_PREFER_ASYNCHRONOUS,
.of_match_table = sdhci_iproc_of_match,
+ .acpi_match_table = ACPI_PTR(sdhci_iproc_acpi_ids),
.pm = &sdhci_pltfm_pmops,
},
.probe = sdhci_iproc_probe,
--
Gitblit v1.6.2