From 9d77db3c730780c8ef5ccd4b66403ff5675cfe4e Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Mon, 13 May 2024 10:30:14 +0000
Subject: [PATCH] modify sin led gpio
---
kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt | 51 +++++++++++++++++++++++++++++++++++++++++++++++++--
1 files changed, 49 insertions(+), 2 deletions(-)
diff --git a/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
index 2e93181..a5c5db6 100644
--- a/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
+++ b/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
@@ -10,10 +10,15 @@
"fsl,imx6sx-usb"
"fsl,imx6ul-usb"
"fsl,imx7d-usb"
+ "fsl,imx7ulp-usb"
"lsi,zevio-usb"
"qcom,ci-hdrc"
"chipidea,usb2"
"xlnx,zynq-usb-2.20a"
+ "nvidia,tegra20-udc"
+ "nvidia,tegra30-udc"
+ "nvidia,tegra114-udc"
+ "nvidia,tegra124-udc"
- reg: base address and length of the registers
- interrupts: interrupt for the USB controller
@@ -80,14 +85,30 @@
controller. It's expected that a mux state of 0 indicates device mode and a
mux state of 1 indicates host mode.
- mux-control-names: Shall be "usb_switch" if mux-controls is specified.
+- pinctrl-names: Names for optional pin modes in "default", "host", "device".
+ In case of HSIC-mode, "idle" and "active" pin modes are mandatory. In this
+ case, the "idle" state needs to pull down the data and strobe pin
+ and the "active" state needs to pull up the strobe pin.
+- pinctrl-n: alternate pin modes
i.mx specific properties
- fsl,usbmisc: phandler of non-core register device, with one
argument that indicate usb controller index
- disable-over-current: disable over current detect
-- over-current-active-high: over current signal polarity is high active,
- typically over current signal polarity is low active.
+- over-current-active-low: over current signal polarity is active low.
+- over-current-active-high: over current signal polarity is active high.
+ It's recommended to specify the over current polarity.
+- power-active-high: power signal polarity is active high
- external-vbus-divider: enables off-chip resistor divider for Vbus
+- samsung,picophy-pre-emp-curr-control: HS Transmitter Pre-Emphasis Current
+ Control. This signal controls the amount of current sourced to the
+ USB_OTG*_DP and USB_OTG*_DN pins after a J-to-K or K-to-J transition.
+ The range is from 0x0 to 0x3, the default value is 0x1.
+ Details can refer to TXPREEMPAMPTUNE0 bits of USBNC_n_PHY_CFG1.
+- samsung,picophy-dc-vol-level-adjust: HS DC Voltage Level Adjustment.
+ Adjust the high-speed transmitter DC level voltage.
+ The range is from 0x0 to 0xf, the default value is 0x3.
+ Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1.
Example:
@@ -109,3 +130,29 @@
mux-controls = <&usb_switch>;
mux-control-names = "usb_switch";
};
+
+Example for HSIC:
+
+ usb@2184400 {
+ compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
+ reg = <0x02184400 0x200>;
+ interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ fsl,usbphy = <&usbphynop1>;
+ fsl,usbmisc = <&usbmisc 2>;
+ phy_type = "hsic";
+ dr_mode = "host";
+ ahb-burst-config = <0x0>;
+ tx-burst-size-dword = <0x10>;
+ rx-burst-size-dword = <0x10>;
+ pinctrl-names = "idle", "active";
+ pinctrl-0 = <&pinctrl_usbh2_idle>;
+ pinctrl-1 = <&pinctrl_usbh2_active>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbnet: smsc@1 {
+ compatible = "usb424,9730";
+ reg = <1>;
+ };
+ };
--
Gitblit v1.6.2