From 9d77db3c730780c8ef5ccd4b66403ff5675cfe4e Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Mon, 13 May 2024 10:30:14 +0000
Subject: [PATCH] modify sin led gpio
---
kernel/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt | 31 +++++++++++++++++++------------
1 files changed, 19 insertions(+), 12 deletions(-)
diff --git a/kernel/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt b/kernel/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt
index 174af2c..325aca5 100644
--- a/kernel/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt
@@ -11,9 +11,16 @@
Xilinx AXI CDMA engine, it does transfers between memory-mapped source
address and a memory-mapped destination address.
+Xilinx AXI MCDMA engine, it does transfer between memory and AXI4 stream
+target devices. It can be configured to have up to 16 independent transmit
+and receive channels.
+
Required properties:
-- compatible: Should be "xlnx,axi-vdma-1.00.a" or "xlnx,axi-dma-1.00.a" or
- "xlnx,axi-cdma-1.00.a""
+- compatible: Should be one of-
+ "xlnx,axi-vdma-1.00.a"
+ "xlnx,axi-dma-1.00.a"
+ "xlnx,axi-cdma-1.00.a"
+ "xlnx,axi-mcdma-1.00.a"
- #dma-cells: Should be <1>, see "dmas" property below
- reg: Should contain VDMA registers location and length.
- xlnx,addrwidth: Should be the vdma addressing size in bits(ex: 32 bits).
@@ -29,7 +36,7 @@
"m_axis_mm2s_aclk", "s_axis_s2mm_aclk"
For CDMA:
Required elements: "s_axi_lite_aclk", "m_axi_aclk"
- FOR AXIDMA:
+ For AXIDMA and MCDMA:
Required elements: "s_axi_lite_aclk"
Optional elements: "m_axi_mm2s_aclk", "m_axi_s2mm_aclk",
"m_axi_sg_aclk"
@@ -37,11 +44,11 @@
Required properties for VDMA:
- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w.
-Optional properties:
-- xlnx,include-sg: Tells configured for Scatter-mode in
- the hardware.
-Optional properties for AXI DMA:
-- xlnx,mcdma: Tells whether configured for multi-channel mode in the hardware.
+Optional properties for AXI DMA and MCDMA:
+- xlnx,sg-length-width: Should be set to the width in bits of the length
+ register as configured in h/w. Takes values {8...26}. If the property
+ is missing or invalid then the default value 23 is used. This is the
+ maximum value that is supported by all IP versions.
Optional properties for VDMA:
- xlnx,flush-fsync: Tells which channel to Flush on Frame sync.
It takes following values:
@@ -54,8 +61,8 @@
For VDMA: It should be either "xlnx,axi-vdma-mm2s-channel" or
"xlnx,axi-vdma-s2mm-channel".
For CDMA: It should be "xlnx,axi-cdma-channel".
- For AXIDMA: It should be either "xlnx,axi-dma-mm2s-channel" or
- "xlnx,axi-dma-s2mm-channel".
+ For AXIDMA and MCDMA: It should be either "xlnx,axi-dma-mm2s-channel"
+ or "xlnx,axi-dma-s2mm-channel".
- interrupts: Should contain per channel VDMA interrupts.
- xlnx,datawidth: Should contain the stream data width, take values
{32,64...1024}.
@@ -68,8 +75,8 @@
enabled/disabled in hardware.
- xlnx,enable-vert-flip: Tells vertical flip is
enabled/disabled in hardware(S2MM path).
-Optional child node properties for AXI DMA:
--dma-channels: Number of dma channels in child node.
+Optional child node properties for MCDMA:
+- dma-channels: Number of dma channels in child node.
Example:
++++++++
--
Gitblit v1.6.2