From 9ca5fbcb63a8dcaee0527f96afb91dc4b4bd8fa9 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Wed, 22 Nov 2023 01:08:11 +0000
Subject: [PATCH] add ip1811 driver
---
kernel/arch/arm64/boot/dts/rockchip/NK-R36S0.dtsi | 370 ++++++++++++++++++++++++++++++++++++++--------------
1 files changed, 269 insertions(+), 101 deletions(-)
diff --git a/kernel/arch/arm64/boot/dts/rockchip/NK-R36S0.dtsi b/kernel/arch/arm64/boot/dts/rockchip/NK-R36S0.dtsi
index 0d47eea..7ad629b 100755
--- a/kernel/arch/arm64/boot/dts/rockchip/NK-R36S0.dtsi
+++ b/kernel/arch/arm64/boot/dts/rockchip/NK-R36S0.dtsi
@@ -8,19 +8,13 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/display/media-bus-format.h>
#include "rk3568.dtsi"
#include "rk3568-evb.dtsi"
/ {
model = "Rockchip RK3568 EVB1 DDR4 V10 Board";
compatible = "rockchip,rk3568-evb1-ddr4-v10", "rockchip,rk3568";
-
- rk_headset: rk-headset {
- compatible = "rockchip_headset";
- headset_gpio = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&hp_det>;
- };
vcc2v5_sys: vcc2v5-ddr {
compatible = "regulator-fixed";
@@ -82,7 +76,7 @@
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc5v0_sys>;
};
-
+#if 0
vcc_camera: vcc-camera-regulator {
compatible = "regulator-fixed";
gpio = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>;
@@ -92,43 +86,151 @@
enable-active-high;
regulator-always-on;
regulator-boot-on;
+ };
+#endif
+
+ ndj_io_init {
+ compatible = "nk_io_control";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nk_io_gpio>;
+
+ //gpio_op0 = <&gpio1 RK_PD0 GPIO_ACTIVE_HIGH>;
+
+ vcc_5v {
+ gpio_num = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; //VCC5_IO_EN_GPIO1_A4_3V3
+ gpio_function = <0>;
+ };
+
+ vcc_12v {
+ gpio_num = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>; //VCC12_IO_EN_GPIO0_C7_3V3
+ gpio_function = <0>;
+ };
+
+ hub_host2_rst {
+ gpio_num = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; //HUB_RST_GPIO4_D2_3V3
+ gpio_function = <3>;
+ };
+
+ hub_host3 {
+ gpio_num = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>; //HOST3_EN_GPIO4_B2_1V8
+ gpio_function = <0>;
+ };
+
+ wake_4g {
+ gpio_num = <&gpio1 RK_PB1 GPIO_ACTIVE_LOW>; //4G_WAKEUP_GPIO01_B1_3V3
+ gpio_function = <0>;
+ };
+
+ air_mode_4g {
+ gpio_num = <&gpio1 RK_PB0 GPIO_ACTIVE_LOW>; //4G_AIR_MODE_GPIO01_B0_3V3
+ gpio_function = <0>;
+ };
+
+ reset_4g {
+ gpio_num = <&gpio1 RK_PB2 GPIO_ACTIVE_LOW>; //4G_RST_GPIO01_B2_3V3
+ gpio_function = <3>;
+ };
+
+ en_4g {
+ gpio_num = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>; //4G_PWREN_H_GPIO0_C6
+ gpio_function = <0>;
+ };
+
+ hp_en {
+ gpio_num = <&gpio3 RK_PA6 GPIO_ACTIVE_HIGH>;//HP_EN_GPIO3_A6_3V3
+ gpio_function = <0>;
+ };
+
+ usb_ogt {
+ gpio_num = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>; //OTG_EN_OC_GPIO0_C2
+ gpio_function = <0>;
+ };
+
+ m2_wifi_pwr {
+ gpio_num = <&gpio3 RK_PC6 GPIO_ACTIVE_HIGH>;//WIFI_PWREN_GPIO3_C6_1V8
+ gpio_function = <0>;
+ };
+
+
+ #if 0
+ do1 {
+ gpio_num = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>;
+ gpio_function = <0>;
+ };
+
+ do2 {
+ gpio_num = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
+ gpio_function = <0>;
+ };
+
+ do3 {
+ gpio_num = <&gpio1 RK_PD1 GPIO_ACTIVE_HIGH>;
+ gpio_function = <0>;
+ };
+
+ do4 {
+ gpio_num = <&gpio1 RK_PD3 GPIO_ACTIVE_HIGH>;
+ gpio_function = <0>;
+ };
+
+ do5 {
+ gpio_num = <&gpio2 RK_PD6 GPIO_ACTIVE_LOW>;
+ gpio_function = <0>;
+ };
+
+ do6 {
+ gpio_num = <&gpio2 RK_PD7 GPIO_ACTIVE_LOW>;
+ gpio_function = <0>;
+ };
+
+ do7 {
+ gpio_num = <&gpio3 RK_PA0 GPIO_ACTIVE_LOW>;
+ gpio_function = <0>;
+ };
+
+ di1 {
+ gpio_num = <&gpio2 RK_PD5 GPIO_ACTIVE_HIGH>;
+ gpio_function = <1>;
+ };
+ #endif
+ };
- };
+ panel: panel {
+ compatible = "simple-panel";
+ backlight = <&backlight>;
+ power-supply = <&vcc3v3_lcd0_n>;
+ enable-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>; //LCD0_VDD_H_GPIO2_D4
+ edp-bl-gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>; //LCD0_PWBLK_H_GPIO0_B7
+ edp-bl-en = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>; //LCD0_BKLT_EN_3V3
+ bus-format = <MEDIA_BUS_FMT_RGB888_1X24>;
+ bpc = <8>;
+ prepare-delay-ms = <200>;
+ enable-delay-ms = <20>;
- nk_io_init {
- compatible = "nk_io_control";
- hub_host2_5v_gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>; //USB_HOST_PWREN_H_GPIO0_A6
- usb_en_oc_gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>; //USB_EN_OC_GPIO0_A5
- lcd_bk_en_gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>; //LCD0_BKLT_EN_3V3
- lcd_pwblk_gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>; //LCD0_BKLT_EN_3V3
- vcc3_io_en_gpio = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>; //VCC3_IO_EN_GPIO0_C4_3V3
- hub_host2_5V_rest_gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; //HUB_RST_GPIO4_D2_3V3
- hub_host3_5v_gpio = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>; //HOST3_EN_GPIO4_B2_1V8
-// hub_host3_5V_rest_gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
- vcc_5v_io = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; //VCC5_IO_EN_GPIO1_A4_3V3
- vcc_12v_io = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>; //VCC12_IO_EN_GPIO0_C7_3V3
- en_4g_gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>; //4G_PWREN_H_GPIO0_C6
- reset_4g_gpio = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>; //4G_RST_GPIO01_B2_3V3
- air_mode_4g_gpio = <&gpio1 RK_PB0 GPIO_ACTIVE_HIGH>; //4G_AIR_MODE_GPIO01_B0_3V3
- wake_4g_gpio = <&gpio1 RK_PB1 GPIO_ACTIVE_HIGH>; //4G_WAKEUP_GPIO01_B1_3V3
-
- edp_enable_gpio = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
- edp_gpio0 = <&gpio3 RK_PD2 GPIO_ACTIVE_LOW>; //7511_GPIO0-GPIO3_D2
- edp_gpio1 = <&gpio3 RK_PD3 GPIO_ACTIVE_LOW>; //7511_GPIO1-GPIO3_D3
- edp_gpio2 = <&gpio3 RK_PD4 GPIO_ACTIVE_LOW>; //7511_GPIO2-GPIO3_D4
- edp_gpio3 = <&gpio3 RK_PD5 GPIO_ACTIVE_LOW>; //7511_GPIO3-GPIO3_D5
- edp_reset = <&gpio3 RK_PD1 GPIO_ACTIVE_LOW>; //7511_RST_GPIO3_D1
-// tp_reset = <&gpio3 RK_PA7 GPIO_ACTIVE_HIGH>;
-// vddio_mipi = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>;
-
- wifi_power_en_gpio = <&gpio3 RK_PC6 GPIO_ACTIVE_HIGH>; //WIFI_PWREN_GPIO3_C6_1V8
-
- // pinctrl-names = "default";
-// pinctrl-0 = <&nk_io_gpio>;
- nodka_lvds = <9>;
- };
-
-
+ display-timings {
+ native-mode = <&timing>;
+ timing: timing {
+ clock-frequency = <72500000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hfront-porch = <70>;
+ hsync-len = <2>;
+ hback-porch = <88>;
+ vfront-porch = <7>;
+ vsync-len = <4>;
+ vback-porch = <17>;
+ hsync-active = <21>;
+ vsync-active = <0>;
+ de-active = <0>;
+ pixelclk-active = <0>;
+ };
+ };
+ ports {
+ panel_in_lvds: endpoint {
+ remote-endpoint = <&lvds_out>;
+ };
+ };
+ };
};
&combphy0_us {
@@ -144,11 +246,11 @@
};
&csi2_dphy_hw {
- status = "okay";
+ status = "disabled";
};
&csi2_dphy0 {
- status = "okay";
+ status = "disabled";
ports {
#address-cells = <1>;
@@ -192,7 +294,7 @@
* when dsi0 is enabled
*/
&dsi0 {
- status = "okay";
+ status = "disabled";
};
&dsi0_in_vp0 {
@@ -200,7 +302,7 @@
};
&dsi0_in_vp1 {
- status = "okay";
+ status = "disabled";
};
&dsi0_panel {
@@ -228,7 +330,30 @@
};
&edp {
- hpd-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
+ //hpd-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
+ force-hpd;
+ status = "disabled";
+};
+
+&lvds {
+ status = "okay";
+ ports {
+ port@1 {
+ reg = <1>;
+ lvds_out: endpoint {
+ remote-endpoint = <&panel_in_lvds>;
+ };
+ };
+
+ };
+};
+
+&route_lvds{
+ status = "okay";
+ connect = <&vp2_out_lvds>;
+};
+
+&lvds_in_vp2 {
status = "okay";
};
@@ -237,18 +362,18 @@
};
&edp_in_vp0 {
- status = "okay";
+ status = "disabled";
};
&edp_in_vp1 {
- status = "disabled";
+ status = "okay";
};
&gmac0 {
phy-mode = "rgmii";
clock_in_out = "output";
- snps,reset-gpio = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
+ snps,reset-gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>;
snps,reset-active-low;
/* Reset time is 20ms, 100ms for rtl8211f */
snps,reset-delays-us = <0 20000 100000>;
@@ -268,7 +393,9 @@
rx_delay = <0x2f>;
phy-handle = <&rgmii_phy0>;
- status = "disabled";
+
+ status = "okay";
+
};
&gmac1 {
@@ -302,9 +429,7 @@
* power-supply should switche to vcc3v3_lcd1_n
* when mipi panel is connected to dsi1.
*/
->1x {
- power-supply = <&vcc3v3_lcd0_n>;
-};
+
&i2c3 {
status = "okay";
@@ -320,13 +445,10 @@
compatible = "nk_mcu";
reg = <0x15>;
};
-
-
-
};
&i2c4 {
- status = "okay";
+ status = "disabled";
gc8034: gc8034@37 {
compatible = "galaxycore,gc8034";
status = "okay";
@@ -372,7 +494,7 @@
};
};
ov5695: ov5695@36 {
- status = "okay";
+ status = "disabled";
compatible = "ovti,ov5695";
reg = <0x36>;
clocks = <&cru CLK_CIF_OUT>;
@@ -421,20 +543,27 @@
status = "okay";
};
+&pcie2x1 {
+ reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie>;
+ status = "okay";
+};
+
&pcie3x2 {
- reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie>;
+ status = "disabled";
+};
+
+&pcie3x1 {
+ rockchip,bifurcation;
+ reset-gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
vpcie3v3-supply = <&vcc3v3_pcie>;
status = "okay";
};
&pinctrl {
- cam {
- camera_pwr: camera-pwr {
- rockchip,pins =
- /* camera power en */
- <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
- };
- };
+
headphone {
hp_det: hp-det {
rockchip,pins = <3 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
@@ -446,36 +575,48 @@
rockchip,pins = <3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
-
- wireless-bluetooth {
- uart8_gpios: uart8-gpios {
- rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+
+ nk_io_init{
+ nk_io_gpio: nk-io-gpio{
+ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>,
+ <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>,
+ <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>,
+ <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>,
+ <4 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>,
+ <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>,
+ <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>,
+ <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>,
+ <1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>,
+ <1 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>,
+ <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>,
+ <3 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>,
+ <3 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>,
+ <3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>,
+ <3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>,
+ <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>,
+ <2 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>,//93 SPI2_CS0_M1_3V3
+ <2 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>,//94 SPI2_MOSI_M1_3V3
+ <2 RK_PD7 RK_FUNC_GPIO &pcfg_pull_none>,//95 SPI2_MISO_M1_3V3
+ <3 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>,//96 SPI2_CLK_M1_3V3
+ <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
+};
- nk_io_gpio: nk_io_gpio_col{
- rockchip,pins =
- <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
- <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
- <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>,
- <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>,
- <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>,
- <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>,
- <1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>,
- <3 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
- };
+&rk809_sound {
+ hp-det-gpio = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
};
&rkisp {
- status = "okay";
+ status = "disabled";
};
&rkisp_mmu {
- status = "okay";
+ status = "disabled";
};
&rkisp_vir0 {
- status = "okay";
+ status = "disabled";
port {
#address-cells = <1>;
@@ -489,13 +630,15 @@
};
&route_dsi0 {
- status = "okay";
+ status = "disabled";
connect = <&vp1_out_dsi0>;
};
+
+
&route_edp {
- status = "okay";
- connect = <&vp0_out_edp>;
+ status = "disabled";
+ connect = <&vp1_out_edp>;
};
&sata2 {
@@ -531,12 +674,12 @@
};
&vcc3v3_lcd0_n {
- gpio = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
&vcc3v3_lcd1_n {
- gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio3 RK_PA3 GPIO_ACTIVE_HIGH>; //MIPI_3V3EN_GPIO3_A3_d_3V3
enable-active-high;
};
@@ -548,15 +691,40 @@
&wireless_bluetooth {
compatible = "bluetooth-platdata";
- clocks = <&rk809 1>;
- clock-names = "ext_clock";
- //wifi-bt-power-toggle;
- uart_rts_gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default", "rts_gpio";
- pinctrl-0 = <&uart8m0_rtsn>;
- pinctrl-1 = <&uart8_gpios>;
- BT,reset_gpio = <&gpio3 RK_PA0 GPIO_ACTIVE_HIGH>;
- BT,wake_gpio = <&gpio3 RK_PA2 GPIO_ACTIVE_HIGH>;
- BT,wake_host_irq = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+};
+
+&uart0 {
status = "okay";
};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;
+ status = "disabled";
+};
+
+&uart3 {
+ status = "okay";
+ pinctrl-0 = <&uart3m1_xfer>;
+};
+
+&uart4 {
+ status = "okay";
+ pinctrl-0 = <&uart4m1_xfer>;
+};
+
+&uart5 {
+ status = "okay";
+ pinctrl-0 = <&uart5m1_xfer>;
+};
+
+&uart7 {
+ status = "okay";
+ pinctrl-0 = <&uart7m1_xfer>;
+};
+
+&uart9 {
+ status = "okay";
+ pinctrl-0 = <&uart9m1_xfer>;
+};
\ No newline at end of file
--
Gitblit v1.6.2