From 8ac6c7a54ed1b98d142dce24b11c6de6a1e239a5 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Tue, 22 Oct 2024 10:36:11 +0000
Subject: [PATCH] 修改4g拨号为QMI,需要在系统里后台执行quectel-CM
---
kernel/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt | 28 +++++++++++++++++++++-------
1 files changed, 21 insertions(+), 7 deletions(-)
diff --git a/kernel/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/kernel/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
index 2df0052..415ccdd 100644
--- a/kernel/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
+++ b/kernel/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
@@ -4,11 +4,16 @@
Each UFS controller instance should have its own node.
Required properties:
-- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0", may
- also list one or more of the following:
- "qcom,msm8994-ufshc"
- "qcom,msm8996-ufshc"
- "qcom,ufshc"
+- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0"
+
+ For Qualcomm SoCs must contain, as below, an
+ SoC-specific compatible along with "qcom,ufshc" and
+ the appropriate jedec string:
+ "qcom,msm8994-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
+ "qcom,msm8996-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
+ "qcom,msm8998-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
+ "qcom,sdm845-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
+ "qcom,sm8150-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
- interrupts : <interrupt mapping for UFS host controller IRQ>
- reg : <registers mapping>
@@ -28,11 +33,16 @@
- vcc-max-microamp : specifies max. load that can be drawn from vcc supply
- vccq-max-microamp : specifies max. load that can be drawn from vccq supply
- vccq2-max-microamp : specifies max. load that can be drawn from vccq2 supply
-- <name>-fixed-regulator : boolean property specifying that <name>-supply is a fixed regulator
- clocks : List of phandle and clock specifier pairs
- clock-names : List of clock input name strings sorted in the same
order as the clocks property.
+ "ref_clk" indicates reference clock frequency.
+ UFS host supplies reference clock to UFS device and UFS device
+ specification allows host to provide one of the 4 frequencies (19.2 MHz,
+ 26 MHz, 38.4 MHz, 52MHz) for reference clock. This "ref_clk" entry is
+ parsed and used to update the reference clock setting in device.
+ Defaults to 26 MHz(as per specification) if not specified by host.
- freq-table-hz : Array of <min max> operating frequencies stored in the same
order as the clocks property. If this property is not
defined or a value in the array is "0" then it is assumed
@@ -41,8 +51,12 @@
-lanes-per-direction : number of lanes available per direction - either 1 or 2.
Note that it is assume same number of lanes is used both
directions at once. If not specified, default is 2 lanes per direction.
+- #reset-cells : Must be <1> for Qualcomm UFS controllers that expose
+ PHY reset from the UFS controller.
- resets : reset node register
- reset-names : describe reset node register, the "rst" corresponds to reset the whole UFS IP.
+- reset-gpios : A phandle and gpio specifier denoting the GPIO connected
+ to the RESET pin of the UFS memory device.
Note: If above properties are not defined it can be assumed that the supply
regulators or clocks are always on.
@@ -54,7 +68,6 @@
interrupts = <0 28 0>;
vdd-hba-supply = <&xxx_reg0>;
- vdd-hba-fixed-regulator;
vcc-supply = <&xxx_reg1>;
vcc-supply-1p8;
vccq-supply = <&xxx_reg2>;
@@ -70,4 +83,5 @@
reset-names = "rst";
phys = <&ufsphy1>;
phy-names = "ufsphy";
+ #reset-cells = <1>;
};
--
Gitblit v1.6.2