From 8ac6c7a54ed1b98d142dce24b11c6de6a1e239a5 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Tue, 22 Oct 2024 10:36:11 +0000
Subject: [PATCH] 修改4g拨号为QMI,需要在系统里后台执行quectel-CM
---
kernel/Documentation/devicetree/bindings/net/dsa/qca8k.txt | 79 ++++++++++++++++++++++++++++++++++++---
1 files changed, 72 insertions(+), 7 deletions(-)
diff --git a/kernel/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/kernel/Documentation/devicetree/bindings/net/dsa/qca8k.txt
index bbcb255..ccbc6d8 100644
--- a/kernel/Documentation/devicetree/bindings/net/dsa/qca8k.txt
+++ b/kernel/Documentation/devicetree/bindings/net/dsa/qca8k.txt
@@ -9,13 +9,22 @@
- #size-cells: must be 0
- #address-cells: must be 1
+Optional properties:
+
+- reset-gpios: GPIO to be used to reset the whole device
+
Subnodes:
The integrated switch subnode should be specified according to the binding
-described in dsa/dsa.txt. As the QCA8K switches do not have a N:N mapping of
-port and PHY id, each subnode describing a port needs to have a valid phandle
-referencing the internal PHY connected to it. The CPU port of this switch is
-always port 0.
+described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external
+mdio-bus each subnode describing a port needs to have a valid phandle
+referencing the internal PHY it is connected to. This is because there's no
+N:N mapping of port and PHY id.
+
+Don't use mixed external and internal mdio-bus configurations, as this is
+not supported by the hardware.
+
+The CPU port of this switch is always port 0.
A CPU port node has the following optional node:
@@ -31,8 +40,9 @@
- 'full-duplex' (boolean, optional), to indicate that full duplex is
used. When absent, half duplex is assumed.
-Example:
+Examples:
+for the external mdio-bus configuration:
&mdio0 {
phy_port1: phy@0 {
@@ -55,12 +65,13 @@
reg = <4>;
};
- switch0@0 {
+ switch@10 {
compatible = "qca,qca8337";
#address-cells = <1>;
#size-cells = <0>;
- reg = <0>;
+ reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+ reg = <0x10>;
ports {
#address-cells = <1>;
@@ -108,3 +119,57 @@
};
};
};
+
+for the internal master mdio-bus configuration:
+
+ &mdio0 {
+ switch@10 {
+ compatible = "qca,qca8337";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+ reg = <0x10>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = 1000;
+ full-duplex;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "wan";
+ };
+ };
+ };
+ };
--
Gitblit v1.6.2