From 8ac6c7a54ed1b98d142dce24b11c6de6a1e239a5 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Tue, 22 Oct 2024 10:36:11 +0000
Subject: [PATCH] 修改4g拨号为QMI,需要在系统里后台执行quectel-CM
---
kernel/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt | 107 ++++++++++++++++++++++++++++++++++++++++++++++++++++-
1 files changed, 105 insertions(+), 2 deletions(-)
diff --git a/kernel/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/kernel/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt
index 9bce578..96c0b14 100644
--- a/kernel/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt
+++ b/kernel/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt
@@ -14,8 +14,16 @@
- "nvidia,tegra124-sdhci": for Tegra124 and Tegra132
- "nvidia,tegra210-sdhci": for Tegra210
- "nvidia,tegra186-sdhci": for Tegra186
-- clocks : Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
+ - "nvidia,tegra194-sdhci": for Tegra194
+- clocks: For Tegra210, Tegra186 and Tegra194 must contain two entries.
+ One for the module clock and one for the timeout clock.
+ For all other Tegra devices, must contain a single entry for
+ the module clock. See ../clocks/clock-bindings.txt for details.
+- clock-names: For Tegra210, Tegra186 and Tegra194 must contain the
+ strings 'sdhci' and 'tmclk' to represent the module and
+ the timeout clocks, respectively.
+ For all other Tegra devices must contain the string 'sdhci'
+ to represent the module clock.
- resets : Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names : Must include the following entries:
@@ -38,3 +46,98 @@
power-gpios = <&gpio 155 0>; /* gpio PT3 */
bus-width = <8>;
};
+
+Optional properties for Tegra210, Tegra186 and Tegra194:
+- pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage
+ configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8"
+ for controllers supporting multiple voltage levels. The order of names
+ should correspond to the pin configuration states in pinctrl-0 and
+ pinctrl-1.
+- pinctrl-names : "sdmmc-3v3-drv" and "sdmmc-1v8-drv" are applicable for
+ Tegra210 where pad config registers are in the pinmux register domain
+ for pull-up-strength and pull-down-strength values configuration when
+ using pads at 3V3 and 1V8 levels.
+- nvidia,only-1-8-v : The presence of this property indicates that the
+ controller operates at a 1.8 V fixed I/O voltage.
+- nvidia,pad-autocal-pull-up-offset-3v3,
+ nvidia,pad-autocal-pull-down-offset-3v3 : Specify drive strength
+ calibration offsets for 3.3 V signaling modes.
+- nvidia,pad-autocal-pull-up-offset-1v8,
+ nvidia,pad-autocal-pull-down-offset-1v8 : Specify drive strength
+ calibration offsets for 1.8 V signaling modes.
+- nvidia,pad-autocal-pull-up-offset-3v3-timeout,
+ nvidia,pad-autocal-pull-down-offset-3v3-timeout : Specify drive
+ strength used as a fallback in case the automatic calibration times
+ out on a 3.3 V signaling mode.
+- nvidia,pad-autocal-pull-up-offset-1v8-timeout,
+ nvidia,pad-autocal-pull-down-offset-1v8-timeout : Specify drive
+ strength used as a fallback in case the automatic calibration times
+ out on a 1.8 V signaling mode.
+- nvidia,pad-autocal-pull-up-offset-sdr104,
+ nvidia,pad-autocal-pull-down-offset-sdr104 : Specify drive strength
+ calibration offsets for SDR104 mode.
+- nvidia,pad-autocal-pull-up-offset-hs400,
+ nvidia,pad-autocal-pull-down-offset-hs400 : Specify drive strength
+ calibration offsets for HS400 mode.
+- nvidia,default-tap : Specify the default inbound sampling clock
+ trimmer value for non-tunable modes.
+- nvidia,default-trim : Specify the default outbound clock trimmer
+ value.
+- nvidia,dqs-trim : Specify DQS trim value for HS400 timing
+
+ Notes on the pad calibration pull up and pulldown offset values:
+ - The property values are drive codes which are programmed into the
+ PD_OFFSET and PU_OFFSET sections of the
+ SDHCI_TEGRA_AUTO_CAL_CONFIG register.
+ - A higher value corresponds to higher drive strength. Please refer
+ to the reference manual of the SoC for correct values.
+ - The SDR104 and HS400 timing specific values are used in
+ corresponding modes if specified.
+
+ Notes on tap and trim values:
+ - The values are used for compensating trace length differences
+ by adjusting the sampling point.
+ - The values are programmed to the Vendor Clock Control Register.
+ Please refer to the reference manual of the SoC for correct
+ values.
+ - The DQS trim values are only used on controllers which support
+ HS400 timing. Only SDMMC4 on Tegra210 and Tegra 186 supports
+ HS400.
+
+Example:
+sdhci@700b0000 {
+ compatible = "nvidia,tegra124-sdhci";
+ reg = <0x0 0x700b0000 0x0 0x200>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA210_CLK_SDMMC1>;
+ clock-names = "sdhci";
+ resets = <&tegra_car 14>;
+ reset-names = "sdhci";
+ pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+ pinctrl-0 = <&sdmmc1_3v3>;
+ pinctrl-1 = <&sdmmc1_1v8>;
+ nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>;
+ nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>;
+ nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>;
+ nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>;
+ status = "disabled";
+};
+
+sdhci@700b0000 {
+ compatible = "nvidia,tegra210-sdhci";
+ reg = <0x0 0x700b0000 0x0 0x200>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA210_CLK_SDMMC1>,
+ <&tegra_car TEGRA210_CLK_SDMMC_LEGACY>;
+ clock-names = "sdhci", "tmclk";
+ resets = <&tegra_car 14>;
+ reset-names = "sdhci";
+ pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+ pinctrl-0 = <&sdmmc1_3v3>;
+ pinctrl-1 = <&sdmmc1_1v8>;
+ nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>;
+ nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>;
+ nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>;
+ nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>;
+ status = "disabled";
+};
--
Gitblit v1.6.2