From 8ac6c7a54ed1b98d142dce24b11c6de6a1e239a5 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Tue, 22 Oct 2024 10:36:11 +0000
Subject: [PATCH] 修改4g拨号为QMI,需要在系统里后台执行quectel-CM
---
kernel/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt | 164 ++++++++++++++++++++++++++++++++++++++++++++++++++----
1 files changed, 151 insertions(+), 13 deletions(-)
diff --git a/kernel/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/kernel/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
index 593be44..ac63ae4 100644
--- a/kernel/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
+++ b/kernel/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
@@ -40,14 +40,78 @@
Required properties:
- compatible: "nvidia,tegra<chip>-vi"
- - reg: Physical base address and length of the controller's registers.
+ - reg: Physical base address and length of the controller registers.
- interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
+ - clocks: clocks: Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - vi
+ - Tegra20/Tegra30/Tegra114/Tegra124:
+ - resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names: Must include the following entries:
+ - vi
+ - Tegra210:
+ - power-domains: Must include venc powergate node as vi is in VE partition.
+
+ ports (optional node)
+ vi can have optional ports node and max 6 ports are supported. Each port
+ should have single 'endpoint' child node. All port nodes are grouped under
+ ports node. Please refer to the bindings defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt
+
+ csi (required node)
+ Tegra210 has CSI part of VI sharing same host interface and register space.
+ So, VI device node should have CSI child node.
+
+ - csi: mipi csi interface to vi
+
+ Required properties:
+ - compatible: "nvidia,tegra210-csi"
+ - reg: Physical base address offset to parent and length of the controller
+ registers.
+ - clocks: Must contain entries csi, cilab, cilcd, cile, csi_tpg clocks.
+ See ../clocks/clock-bindings.txt for details.
+ - power-domains: Must include sor powergate node as csicil is in
+ SOR partition.
+
+ channel (optional nodes)
+ Maximum 6 channels are supported with each csi brick as either x4 or x2
+ based on hw connectivity to sensor.
+
+ Required properties:
+ - reg: csi port number. Valid port numbers are 0 through 5.
+ - nvidia,mipi-calibrate: Should contain a phandle and a specifier
+ specifying which pads are used by this CSI port and need to be
+ calibrated. See also ../display/tegra/nvidia,tegra114-mipi.txt.
+
+ Each channel node must contain 2 port nodes which can be grouped
+ under 'ports' node and each port should have a single child 'endpoint'
+ node.
+
+ ports node
+ Please refer to the bindings defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt
+
+ ports node must contain below 2 port nodes.
+ port@0 with single child 'endpoint' node always a sink.
+ port@1 with single child 'endpoint' node always a source.
+
+ port@0 (required node)
+ Required properties:
+ - reg: 0
+
+ endpoint (required node)
+ Required properties:
+ - data-lanes: an array of data lane from 1 to 4. Valid array
+ lengths are 1/2/4.
+ - remote-endpoint: phandle to sensor 'endpoint' node.
+
+ port@1 (required node)
+ Required properties:
+ - reg: 1
+
+ endpoint (required node)
+ Required properties:
+ - remote-endpoint: phandle to vi port 'endpoint' node.
- epp: encoder pre-processor
@@ -238,6 +302,9 @@
- nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- nvidia,edid: supplies a binary EDID blob
- nvidia,panel: phandle of a display panel
+ - nvidia,xbar-cfg: 5 cells containing the crossbar configuration. Each lane
+ of the SOR, identified by the cell's index, is mapped via the crossbar to
+ the pad specified by the cell's value.
Optional properties when driving an eDP output:
- nvidia,dpaux: phandle to a DispayPort AUX interface
@@ -306,13 +373,84 @@
reset-names = "mpe";
};
- vi {
- compatible = "nvidia,tegra20-vi";
- reg = <0x54080000 0x00040000>;
- interrupts = <0 69 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_VI>;
- resets = <&tegra_car 100>;
- reset-names = "vi";
+ vi@54080000 {
+ compatible = "nvidia,tegra210-vi";
+ reg = <0x0 0x54080000 0x0 0x700>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ assigned-clocks = <&tegra_car TEGRA210_CLK_VI>;
+ assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>;
+
+ clocks = <&tegra_car TEGRA210_CLK_VI>;
+ power-domains = <&pd_venc>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ranges = <0x0 0x0 0x54080000 0x2000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ imx219_vi_in0: endpoint {
+ remote-endpoint = <&imx219_csi_out0>;
+ };
+ };
+ };
+
+ csi@838 {
+ compatible = "nvidia,tegra210-csi";
+ reg = <0x838 0x1300>;
+ assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>,
+ <&tegra_car TEGRA210_CLK_CILCD>,
+ <&tegra_car TEGRA210_CLK_CILE>,
+ <&tegra_car TEGRA210_CLK_CSI_TPG>;
+ assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>,
+ <&tegra_car TEGRA210_CLK_PLL_P>,
+ <&tegra_car TEGRA210_CLK_PLL_P>;
+ assigned-clock-rates = <102000000>,
+ <102000000>,
+ <102000000>,
+ <972000000>;
+
+ clocks = <&tegra_car TEGRA210_CLK_CSI>,
+ <&tegra_car TEGRA210_CLK_CILAB>,
+ <&tegra_car TEGRA210_CLK_CILCD>,
+ <&tegra_car TEGRA210_CLK_CILE>,
+ <&tegra_car TEGRA210_CLK_CSI_TPG>;
+ clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg";
+ power-domains = <&pd_sor>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@0 {
+ reg = <0>;
+ nvidia,mipi-calibrate = <&mipi 0x001>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ imx219_csi_in0: endpoint {
+ data-lanes = <1 2>;
+ remote-endpoint = <&imx219_out0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ imx219_csi_out0: endpoint {
+ remote-endpoint = <&imx219_vi_in0>;
+ };
+ };
+ };
+ };
+ };
};
epp {
--
Gitblit v1.6.2