From 748e4f3d702def1a4bff191e0cf93b6a05340f01 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Fri, 10 May 2024 07:41:34 +0000
Subject: [PATCH] add gpio led uart
---
kernel/arch/arm/boot/dts/tegra124-nyan.dtsi | 298 ++++++++++++++++++++++++++++-------------------------------
1 files changed, 143 insertions(+), 155 deletions(-)
diff --git a/kernel/arch/arm/boot/dts/tegra124-nyan.dtsi b/kernel/arch/arm/boot/dts/tegra124-nyan.dtsi
index bc85b6a..5f71add 100644
--- a/kernel/arch/arm/boot/dts/tegra124-nyan.dtsi
+++ b/kernel/arch/arm/boot/dts/tegra124-nyan.dtsi
@@ -48,6 +48,9 @@
sor@54540000 {
status = "okay";
+ avdd-io-hdmi-dp-supply = <&vdd_3v3_hdmi>;
+ vdd-hdmi-dp-pll-supply = <&vdd_hdmi_pll>;
+
nvidia,dpaux = <&dpaux>;
nvidia,panel = <&panel>;
};
@@ -370,7 +373,7 @@
spi-max-frequency = <25000000>;
flash@0 {
- compatible = "winbond,w25q32dw";
+ compatible = "winbond,w25q32dw", "jedec,spi-nor";
spi-max-frequency = <25000000>;
reg = <0>;
};
@@ -413,6 +416,11 @@
padctl@7009f000 {
status = "okay";
+
+ avdd-pll-utmip-supply = <&vddio_1v8>;
+ avdd-pll-erefe-supply = <&avdd_1v05_run>;
+ avdd-pex-pll-supply = <&vdd_1v05_run>;
+ hvdd-pex-pll-e-supply = <&vdd_3v3_lp0>;
pads {
usb2 {
@@ -490,7 +498,7 @@
reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
};
- sdhci@700b0000 { /* WiFi/BT on this bus */
+ mmc@700b0000 { /* WiFi/BT on this bus */
status = "okay";
bus-width = <4>;
no-1-8-v;
@@ -501,7 +509,7 @@
keep-power-in-suspend;
};
- sdhci@700b0400 { /* SD Card on this bus */
+ mmc@700b0400 { /* SD Card on this bus */
status = "okay";
cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
@@ -510,7 +518,7 @@
vqmmc-supply = <&vddio_sdmmc3>;
};
- sdhci@700b0600 { /* eMMC on this bus */
+ mmc@700b0600 { /* eMMC on this bus */
status = "okay";
bus-width = <8>;
no-1-8-v;
@@ -574,17 +582,10 @@
256>;
};
- clocks {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- clk32k_in: clock@0 {
- compatible = "fixed-clock";
- reg = <0>;
- #clock-cells = <0>;
- clock-frequency = <32768>;
- };
+ clk32k_in: clock@0 {
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ #clock-cells = <0>;
};
cpus {
@@ -614,157 +615,138 @@
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
+ vdd_mux: regulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "+VDD_MUX";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- vdd_mux: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "+VDD_MUX";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ vdd_5v0_sys: regulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "+5V_SYS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vdd_mux>;
+ };
- vdd_5v0_sys: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "+5V_SYS";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vdd_mux>;
- };
+ vdd_3v3_sys: regulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "+3.3V_SYS";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vdd_mux>;
+ };
- vdd_3v3_sys: regulator@2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "+3.3V_SYS";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vdd_mux>;
- };
+ vdd_3v3_run: regulator@3 {
+ compatible = "regulator-fixed";
+ regulator-name = "+3.3V_RUN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_3v3_sys>;
+ };
- vdd_3v3_run: regulator@3 {
- compatible = "regulator-fixed";
- reg = <3>;
- regulator-name = "+3.3V_RUN";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- vin-supply = <&vdd_3v3_sys>;
- };
+ vdd_3v3_hdmi: regulator@4 {
+ compatible = "regulator-fixed";
+ regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vdd_3v3_run>;
+ };
- vdd_3v3_hdmi: regulator@4 {
- compatible = "regulator-fixed";
- reg = <4>;
- regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- vin-supply = <&vdd_3v3_run>;
- };
+ vdd_led: regulator@5 {
+ compatible = "regulator-fixed";
+ regulator-name = "+VDD_LED";
+ gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_mux>;
+ };
- vdd_led: regulator@5 {
- compatible = "regulator-fixed";
- reg = <5>;
- regulator-name = "+VDD_LED";
- gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
- enable-active-high;
- vin-supply = <&vdd_mux>;
- };
+ vdd_5v0_ts: regulator@6 {
+ compatible = "regulator-fixed";
+ regulator-name = "+5V_VDD_TS_SW";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_5v0_sys>;
+ };
- vdd_5v0_ts: regulator@6 {
- compatible = "regulator-fixed";
- reg = <6>;
- regulator-name = "+5V_VDD_TS_SW";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-boot-on;
- gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
- enable-active-high;
- vin-supply = <&vdd_5v0_sys>;
- };
+ vdd_usb1_vbus: regulator@7 {
+ compatible = "regulator-fixed";
+ regulator-name = "+5V_USB_HS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ gpio-open-drain;
+ vin-supply = <&vdd_5v0_sys>;
+ };
- vdd_usb1_vbus: regulator@7 {
- compatible = "regulator-fixed";
- reg = <7>;
- regulator-name = "+5V_USB_HS";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
- enable-active-high;
- gpio-open-drain;
- vin-supply = <&vdd_5v0_sys>;
- };
+ vdd_usb3_vbus: regulator@8 {
+ compatible = "regulator-fixed";
+ regulator-name = "+5V_USB_SS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ gpio-open-drain;
+ vin-supply = <&vdd_5v0_sys>;
+ };
- vdd_usb3_vbus: regulator@8 {
- compatible = "regulator-fixed";
- reg = <8>;
- regulator-name = "+5V_USB_SS";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
- enable-active-high;
- gpio-open-drain;
- vin-supply = <&vdd_5v0_sys>;
- };
+ vdd_3v3_panel: regulator@9 {
+ compatible = "regulator-fixed";
+ regulator-name = "+3.3V_PANEL";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_3v3_run>;
+ };
- vdd_3v3_panel: regulator@9 {
- compatible = "regulator-fixed";
- reg = <9>;
- regulator-name = "+3.3V_PANEL";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- vin-supply = <&vdd_3v3_run>;
- };
+ vdd_3v3_lp0: regulator@10 {
+ compatible = "regulator-fixed";
+ regulator-name = "+3.3V_LP0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ /*
+ * TODO: find a way to wire this up with the USB EHCI
+ * controllers so that it can be enabled on demand.
+ */
+ regulator-always-on;
+ gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_3v3_sys>;
+ };
- vdd_3v3_lp0: regulator@10 {
- compatible = "regulator-fixed";
- reg = <10>;
- regulator-name = "+3.3V_LP0";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- /*
- * TODO: find a way to wire this up with the USB EHCI
- * controllers so that it can be enabled on demand.
- */
- regulator-always-on;
- gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- vin-supply = <&vdd_3v3_sys>;
- };
+ vdd_hdmi_pll: regulator@11 {
+ compatible = "regulator-fixed";
+ regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
+ vin-supply = <&vdd_1v05_run>;
+ };
- vdd_hdmi_pll: regulator@11 {
- compatible = "regulator-fixed";
- reg = <11>;
- regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
- vin-supply = <&vdd_1v05_run>;
- };
-
- vdd_5v0_hdmi: regulator@12 {
- compatible = "regulator-fixed";
- reg = <12>;
- regulator-name = "+5V_HDMI_CON";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
- enable-active-high;
- vin-supply = <&vdd_5v0_sys>;
- };
+ vdd_5v0_hdmi: regulator@12 {
+ compatible = "regulator-fixed";
+ regulator-name = "+5V_HDMI_CON";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_5v0_sys>;
};
sound {
@@ -783,9 +765,15 @@
clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
<&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
- <&tegra_car TEGRA124_CLK_EXTERN1>;
+ <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
clock-names = "pll_a", "pll_a_out0", "mclk";
+ assigned-clocks = <&tegra_car TEGRA124_CLK_EXTERN1>,
+ <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+ assigned-clock-parents = <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
+ <&tegra_car TEGRA124_CLK_EXTERN1>;
+
nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>;
nvidia,mic-det-gpios =
<&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
--
Gitblit v1.6.2