From 6778948f9de86c3cfaf36725a7c87dcff9ba247f Mon Sep 17 00:00:00 2001 From: hc <hc@nodka.com> Date: Mon, 11 Dec 2023 08:20:59 +0000 Subject: [PATCH] kernel_5.10 no rt --- kernel/drivers/mtd/nand/raw/Kconfig | 797 ++++++++++++++++++++++++++++---------------------------- 1 files changed, 395 insertions(+), 402 deletions(-) diff --git a/kernel/drivers/mtd/nand/raw/Kconfig b/kernel/drivers/mtd/nand/raw/Kconfig index b6119dd..2cc533e 100644 --- a/kernel/drivers/mtd/nand/raw/Kconfig +++ b/kernel/drivers/mtd/nand/raw/Kconfig @@ -1,34 +1,30 @@ -config MTD_NAND_ECC +# SPDX-License-Identifier: GPL-2.0-only +config MTD_NAND_ECC_SW_HAMMING tristate -config MTD_NAND_ECC_SMC +config MTD_NAND_ECC_SW_HAMMING_SMC bool "NAND ECC Smart Media byte order" - depends on MTD_NAND_ECC + depends on MTD_NAND_ECC_SW_HAMMING default n help Software ECC according to the Smart Media Specification. The original Linux implementation had byte 0 and 1 swapped. - -menuconfig MTD_NAND +menuconfig MTD_RAW_NAND tristate "Raw/Parallel NAND Device Support" - depends on MTD + select MTD_NAND_CORE select MTD_NAND_ECC + select MTD_NAND_ECC_SW_HAMMING help This enables support for accessing all type of raw/parallel NAND flash devices. For further information see <http://www.linux-mtd.infradead.org/doc/nand.html>. -if MTD_NAND +if MTD_RAW_NAND -config MTD_NAND_BCH - tristate - select BCH - depends on MTD_NAND_ECC_BCH - default MTD_NAND - -config MTD_NAND_ECC_BCH +config MTD_NAND_ECC_SW_BCH bool "Support software BCH ECC" + select BCH default n help This enables support for software BCH error correction. Binary BCH @@ -36,15 +32,13 @@ ECC codes. They are used with NAND devices requiring more than 1 bit of error correction. -config MTD_SM_COMMON - tristate - default n +comment "Raw/parallel NAND flash controllers" config MTD_NAND_DENALI tristate config MTD_NAND_DENALI_PCI - tristate "Support Denali NAND controller on Intel Moorestown" + tristate "Denali NAND controller on Intel Moorestown" select MTD_NAND_DENALI depends on PCI help @@ -52,31 +46,22 @@ Denali NAND controller core. config MTD_NAND_DENALI_DT - tristate "Support Denali NAND controller as a DT device" + tristate "Denali NAND controller as a DT device" select MTD_NAND_DENALI depends on HAS_DMA && HAVE_CLK && OF help Enable the driver for NAND flash on platforms using a Denali NAND controller as a DT device. -config MTD_NAND_GPIO - tristate "GPIO assisted NAND Flash driver" - depends on GPIOLIB || COMPILE_TEST - depends on HAS_IOMEM - help - This enables a NAND flash driver where control signals are - connected to GPIO pins, and commands and data are communicated - via a memory mapped interface. - config MTD_NAND_AMS_DELTA - tristate "NAND Flash device on Amstrad E3" - depends on MACH_AMS_DELTA + tristate "Amstrad E3 NAND controller" + depends on MACH_AMS_DELTA || COMPILE_TEST default y help Support for NAND flash on Amstrad E3 (Delta). config MTD_NAND_OMAP2 - tristate "NAND Flash device on OMAP2, OMAP3, OMAP4 and Keystone" + tristate "OMAP2, OMAP3, OMAP4 and Keystone NAND controller" depends on ARCH_OMAP2PLUS || ARCH_KEYSTONE || COMPILE_TEST depends on HAS_IOMEM help @@ -98,18 +83,6 @@ config MTD_NAND_OMAP_BCH_BUILD def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH -config MTD_NAND_RICOH - tristate "Ricoh xD card reader" - default n - depends on PCI - select MTD_SM_COMMON - help - Enable support for Ricoh R5C852 xD card reader - You also need to enable ether - NAND SSFDC (SmartMedia) read only translation layer' or new - expermental, readwrite - 'SmartMedia/xD new translation layer' - config MTD_NAND_AU1550 tristate "Au1550/1200 NAND support" depends on MIPS_ALCHEMY @@ -117,8 +90,15 @@ This enables the driver for the NAND flash controller on the AMD/Alchemy 1550 SOC. +config MTD_NAND_NDFC + tristate "IBM/MCC 4xx NAND controller" + depends on 4xx + select MTD_NAND_ECC_SW_HAMMING_SMC + help + NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs + config MTD_NAND_S3C2410 - tristate "NAND Flash support for Samsung S3C SoCs" + tristate "Samsung S3C NAND controller" depends on ARCH_S3C24XX || ARCH_S3C64XX help This enables the NAND flash controller on the S3C24xx and S3C64xx @@ -128,17 +108,10 @@ must advertise a platform_device for the driver to attach. config MTD_NAND_S3C2410_DEBUG - bool "Samsung S3C NAND driver debug" + bool "Samsung S3C NAND controller debug" depends on MTD_NAND_S3C2410 help Enable debugging of the S3C NAND driver - -config MTD_NAND_NDFC - tristate "NDFC NanD Flash Controller" - depends on 4xx - select MTD_NAND_ECC_SMC - help - NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs config MTD_NAND_S3C2410_CLKSTOP bool "Samsung S3C NAND IDLE clock stop" @@ -151,11 +124,379 @@ approximately 5mA of power when there is nothing happening. config MTD_NAND_TANGO - tristate "NAND Flash support for Tango chips" + tristate "Tango NAND controller" depends on ARCH_TANGO || COMPILE_TEST depends on HAS_IOMEM help Enables the NAND Flash controller on Tango chips. + +config MTD_NAND_SHARPSL + tristate "Sharp SL Series (C7xx + others) NAND controller" + depends on ARCH_PXA || COMPILE_TEST + depends on HAS_IOMEM + +config MTD_NAND_CAFE + tristate "OLPC CAFÉ NAND controller" + depends on PCI + select REED_SOLOMON + select REED_SOLOMON_DEC16 + help + Use NAND flash attached to the CAFÉ chip designed for the OLPC + laptop. + +config MTD_NAND_CS553X + tristate "CS5535/CS5536 (AMD Geode companion) NAND controller" + depends on X86_32 + depends on !UML && HAS_IOMEM + help + The CS553x companion chips for the AMD Geode processor + include NAND flash controllers with built-in hardware ECC + capabilities; enabling this option will allow you to use + these. The driver will check the MSRs to verify that the + controller is enabled for NAND, and currently requires that + the controller be in MMIO mode. + + If you say "m", the module will be called cs553x_nand. + +config MTD_NAND_ATMEL + tristate "Atmel AT91 NAND Flash/SmartMedia NAND controller" + depends on ARCH_AT91 || COMPILE_TEST + depends on HAS_IOMEM + select GENERIC_ALLOCATOR + select MFD_ATMEL_SMC + help + Enables support for NAND Flash / Smart Media Card interface + on Atmel AT91 processors. + +config MTD_NAND_ORION + tristate "Marvell Orion NAND controller" + depends on PLAT_ORION + help + This enables the NAND flash controller on Orion machines. + + No board specific support is done by this driver, each board + must advertise a platform_device for the driver to attach. + +config MTD_NAND_MARVELL + tristate "Marvell EBU NAND controller" + depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU || \ + COMPILE_TEST + depends on HAS_IOMEM + help + This enables the NAND flash controller driver for Marvell boards, + including: + - PXA3xx processors (NFCv1) + - 32-bit Armada platforms (XP, 37x, 38x, 39x) (NFCv2) + - 64-bit Aramda platforms (7k, 8k) (NFCv2) + +config MTD_NAND_SLC_LPC32XX + tristate "NXP LPC32xx SLC NAND controller" + depends on ARCH_LPC32XX || COMPILE_TEST + depends on HAS_IOMEM + help + Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell + chips) NAND controller. This is the default for the PHYTEC 3250 + reference board which contains a NAND256R3A2CZA6 chip. + + Please check the actual NAND chip connected and its support + by the SLC NAND controller. + +config MTD_NAND_MLC_LPC32XX + tristate "NXP LPC32xx MLC NAND controller" + depends on ARCH_LPC32XX || COMPILE_TEST + depends on HAS_IOMEM + help + Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND + controller. This is the default for the WORK92105 controller + board. + + Please check the actual NAND chip connected and its support + by the MLC NAND controller. + +config MTD_NAND_PASEMI + tristate "PA Semi PWRficient NAND controller" + depends on PPC_PASEMI + help + Enables support for NAND Flash interface on PA Semi PWRficient + based boards + +config MTD_NAND_TMIO + tristate "Toshiba Mobile IO NAND controller" + depends on MFD_TMIO + help + Support for NAND flash connected to a Toshiba Mobile IO + Controller in some PDAs, including the Sharp SL6000x. + +config MTD_NAND_BRCMNAND + tristate "Broadcom STB NAND controller" + depends on ARM || ARM64 || MIPS || COMPILE_TEST + depends on HAS_IOMEM + help + Enables the Broadcom NAND controller driver. The controller was + originally designed for Set-Top Box but is used on various BCM7xxx, + BCM3xxx, BCM63xxx, iProc/Cygnus and more. + +config MTD_NAND_BCM47XXNFLASH + tristate "BCM4706 BCMA NAND controller" + depends on BCMA_NFLASH + depends on BCMA + help + BCMA bus can have various flash memories attached, they are + registered by bcma as platform devices. This enables driver for + NAND flash memories. For now only BCM4706 is supported. + +config MTD_NAND_OXNAS + tristate "Oxford Semiconductor NAND controller" + depends on ARCH_OXNAS || COMPILE_TEST + depends on HAS_IOMEM + help + This enables the NAND flash controller on Oxford Semiconductor SoCs. + +config MTD_NAND_MPC5121_NFC + tristate "MPC5121 NAND controller" + depends on PPC_MPC512x + help + This enables the driver for the NAND flash controller on the + MPC5121 SoC. + +config MTD_NAND_GPMI_NAND + tristate "Freescale GPMI NAND controller" + depends on MXS_DMA + help + Enables NAND Flash support for IMX23, IMX28 or IMX6. + The GPMI controller is very powerful, with the help of BCH + module, it can do the hardware ECC. The GPMI supports several + NAND flashs at the same time. + +config MTD_NAND_FSL_ELBC + tristate "Freescale eLBC NAND controller" + depends on FSL_SOC + select FSL_LBC + help + Various Freescale chips, including the 8313, include a NAND Flash + Controller Module with built-in hardware ECC capabilities. + Enabling this option will enable you to use this to control + external NAND devices. + +config MTD_NAND_FSL_IFC + tristate "Freescale IFC NAND controller" + depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A || COMPILE_TEST + depends on HAS_IOMEM + select FSL_IFC + select MEMORY + help + Various Freescale chips e.g P1010, include a NAND Flash machine + with built-in hardware ECC capabilities. + Enabling this option will enable you to use this to control + external NAND devices. + +config MTD_NAND_FSL_UPM + tristate "Freescale UPM NAND controller" + depends on PPC_83xx || PPC_85xx + select FSL_LBC + help + Enables support for NAND Flash chips wired onto Freescale PowerPC + processor localbus with User-Programmable Machine support. + +config MTD_NAND_VF610_NFC + tristate "Freescale VF610/MPC5125 NAND controller" + depends on (SOC_VF610 || COMPILE_TEST) + depends on HAS_IOMEM + help + Enables support for NAND Flash Controller on some Freescale + processors like the VF610, MPC5125, MCF54418 or Kinetis K70. + The driver supports a maximum 2k page size. With 2k pages and + 64 bytes or more of OOB, hardware ECC with up to 32-bit error + correction is supported. Hardware ECC is only enabled through + device tree. + +config MTD_NAND_MXC + tristate "Freescale MXC NAND controller" + depends on ARCH_MXC || COMPILE_TEST + depends on HAS_IOMEM + help + This enables the driver for the NAND flash controller on the + MXC processors. + +config MTD_NAND_SH_FLCTL + tristate "Renesas SuperH FLCTL NAND controller" + depends on SUPERH || COMPILE_TEST + depends on HAS_IOMEM + help + Several Renesas SuperH CPU has FLCTL. This option enables support + for NAND Flash using FLCTL. + +config MTD_NAND_DAVINCI + tristate "DaVinci/Keystone NAND controller" + depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF) || COMPILE_TEST + depends on HAS_IOMEM + help + Enable the driver for NAND flash chips on Texas Instruments + DaVinci/Keystone processors. + +config MTD_NAND_TXX9NDFMC + tristate "TXx9 NAND controller" + depends on SOC_TX4938 || SOC_TX4939 || COMPILE_TEST + depends on HAS_IOMEM + help + This enables the NAND flash controller on the TXx9 SoCs. + +config MTD_NAND_SOCRATES + tristate "Socrates NAND controller" + depends on SOCRATES + help + Enables support for NAND Flash chips wired onto Socrates board. + +source "drivers/mtd/nand/raw/ingenic/Kconfig" + +config MTD_NAND_FSMC + tristate "ST Micros FSMC NAND controller" + depends on OF && HAS_IOMEM + depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300 || \ + COMPILE_TEST + help + Enables support for NAND Flash chips on the ST Microelectronics + Flexible Static Memory Controller (FSMC) + +config MTD_NAND_XWAY + bool "Lantiq XWAY NAND controller" + depends on LANTIQ && SOC_TYPE_XWAY + help + Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached + to the External Bus Unit (EBU). + +config MTD_NAND_SUNXI + tristate "Allwinner NAND controller" + depends on ARCH_SUNXI || COMPILE_TEST + depends on HAS_IOMEM + help + Enables support for NAND Flash chips on Allwinner SoCs. + +config MTD_NAND_HISI504 + tristate "Hisilicon Hip04 NAND controller" + depends on ARCH_HISI || COMPILE_TEST + depends on HAS_IOMEM + help + Enables support for NAND controller on Hisilicon SoC Hip04. + +config MTD_NAND_QCOM + tristate "QCOM NAND controller" + depends on ARCH_QCOM || COMPILE_TEST + depends on HAS_IOMEM + help + Enables support for NAND flash chips on SoCs containing the EBI2 NAND + controller. This controller is found on IPQ806x SoC. + +config MTD_NAND_MTK + tristate "MTK NAND controller" + depends on ARCH_MEDIATEK || COMPILE_TEST + depends on HAS_IOMEM + help + Enables support for NAND controller on MTK SoCs. + This controller is found on mt27xx, mt81xx, mt65xx SoCs. + +config MTD_NAND_MXIC + tristate "Macronix raw NAND controller" + depends on HAS_IOMEM || COMPILE_TEST + help + This selects the Macronix raw NAND controller driver. + +config MTD_NAND_TEGRA + tristate "NVIDIA Tegra NAND controller" + depends on ARCH_TEGRA || COMPILE_TEST + depends on HAS_IOMEM + help + Enables support for NAND flash controller on NVIDIA Tegra SoC. + The driver has been developed and tested on a Tegra 2 SoC. DMA + support, raw read/write page as well as HW ECC read/write page + is supported. Extra OOB bytes when using HW ECC are currently + not supported. + +config MTD_NAND_STM32_FMC2 + tristate "Support for NAND controller on STM32MP SoCs" + depends on MACH_STM32MP157 || COMPILE_TEST + select MFD_SYSCON + help + Enables support for NAND Flash chips on SoCs containing the FMC2 + NAND controller. This controller is found on STM32MP SoCs. + The controller supports a maximum 8k page size and supports + a maximum 8-bit correction error per sector of 512 bytes. + +config MTD_NAND_MESON + tristate "Support for NAND controller on Amlogic's Meson SoCs" + depends on ARCH_MESON || COMPILE_TEST + select MFD_SYSCON + help + Enables support for NAND controller on Amlogic's Meson SoCs. + This controller is found on Meson SoCs. + +config MTD_NAND_GPIO + tristate "GPIO assisted NAND controller" + depends on GPIOLIB || COMPILE_TEST + depends on HAS_IOMEM + help + This enables a NAND flash driver where control signals are + connected to GPIO pins, and commands and data are communicated + via a memory mapped interface. + +config MTD_NAND_PLATFORM + tristate "Generic NAND controller" + depends on HAS_IOMEM + help + This implements a generic NAND driver for on-SOC platform + devices. You will need to provide platform-specific functions + via platform_data. + +config MTD_NAND_CADENCE + tristate "Support Cadence NAND (HPNFC) controller" + depends on (OF || COMPILE_TEST) && HAS_IOMEM + help + Enable the driver for NAND flash on platforms using a Cadence NAND + controller. + +config MTD_NAND_ARASAN + tristate "Support for Arasan NAND flash controller" + depends on HAS_IOMEM && HAS_DMA + select BCH + help + Enables the driver for the Arasan NAND flash controller on + Zynq Ultrascale+ MPSoC. + +config MTD_NAND_ROCKCHIP + tristate "Rockchip NAND controller" + depends on ARCH_ROCKCHIP && HAS_IOMEM + help + Enables support for NAND controller on Rockchip SoCs. + There are four different versions of NAND FLASH Controllers, + including: + NFC v600: RK2928, RK3066, RK3188 + NFC v622: RK3036, RK3128 + NFC v800: RK3308, RV1108 + NFC v900: PX30, RK3326 + +comment "Misc" + +config MTD_SM_COMMON + tristate + default n + +config MTD_NAND_NANDSIM + tristate "Support for NAND Flash Simulator" + help + The simulator may simulate various NAND flash chips for the + MTD nand layer. + +config MTD_NAND_RICOH + tristate "Ricoh xD card reader" + default n + depends on PCI + select MTD_SM_COMMON + help + Enable support for Ricoh R5C852 xD card reader + You also need to enable ether + NAND SSFDC (SmartMedia) read only translation layer' or new + expermental, readwrite + 'SmartMedia/xD new translation layer' config MTD_NAND_DISKONCHIP tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)" @@ -227,352 +568,4 @@ load time (assuming you build diskonchip as a module) with the module parameter "inftl_bbt_write=1". -config MTD_NAND_DOCG4 - tristate "Support for DiskOnChip G4" - depends on HAS_IOMEM - select BCH - select BITREVERSE - help - Support for diskonchip G4 nand flash, found in various smartphones and - PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba - Portege G900, Asus P526, and O2 XDA Zinc. - - With this driver you will be able to use UBI and create a ubifs on the - device, so you may wish to consider enabling UBI and UBIFS as well. - - These devices ship with the Mys/Sandisk SAFTL formatting, for which - there is currently no mtd parser, so you may want to use command line - partitioning to segregate write-protected blocks. On the Treo680, the - first five erase blocks (256KiB each) are write-protected, followed - by the block containing the saftl partition table. This is probably - typical. - -config MTD_NAND_SHARPSL - tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)" - depends on ARCH_PXA || COMPILE_TEST - depends on HAS_IOMEM - -config MTD_NAND_CAFE - tristate "NAND support for OLPC CAFÉ chip" - depends on PCI - select REED_SOLOMON - select REED_SOLOMON_DEC16 - help - Use NAND flash attached to the CAFÉ chip designed for the OLPC - laptop. - -config MTD_NAND_CS553X - tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)" - depends on X86_32 - depends on !UML && HAS_IOMEM - help - The CS553x companion chips for the AMD Geode processor - include NAND flash controllers with built-in hardware ECC - capabilities; enabling this option will allow you to use - these. The driver will check the MSRs to verify that the - controller is enabled for NAND, and currently requires that - the controller be in MMIO mode. - - If you say "m", the module will be called cs553x_nand. - -config MTD_NAND_ATMEL - tristate "Support for NAND Flash / SmartMedia on AT91" - depends on ARCH_AT91 || COMPILE_TEST - depends on HAS_IOMEM - select GENERIC_ALLOCATOR - select MFD_ATMEL_SMC - help - Enables support for NAND Flash / Smart Media Card interface - on Atmel AT91 processors. - -config MTD_NAND_MARVELL - tristate "NAND controller support on Marvell boards" - depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU || \ - COMPILE_TEST - depends on HAS_IOMEM - help - This enables the NAND flash controller driver for Marvell boards, - including: - - PXA3xx processors (NFCv1) - - 32-bit Armada platforms (XP, 37x, 38x, 39x) (NFCv2) - - 64-bit Aramda platforms (7k, 8k) (NFCv2) - -config MTD_NAND_SLC_LPC32XX - tristate "NXP LPC32xx SLC Controller" - depends on ARCH_LPC32XX || COMPILE_TEST - depends on HAS_IOMEM - help - Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell - chips) NAND controller. This is the default for the PHYTEC 3250 - reference board which contains a NAND256R3A2CZA6 chip. - - Please check the actual NAND chip connected and its support - by the SLC NAND controller. - -config MTD_NAND_MLC_LPC32XX - tristate "NXP LPC32xx MLC Controller" - depends on ARCH_LPC32XX || COMPILE_TEST - depends on HAS_IOMEM - help - Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND - controller. This is the default for the WORK92105 controller - board. - - Please check the actual NAND chip connected and its support - by the MLC NAND controller. - -config MTD_NAND_CM_X270 - tristate "Support for NAND Flash on CM-X270 modules" - depends on MACH_ARMCORE - -config MTD_NAND_PASEMI - tristate "NAND support for PA Semi PWRficient" - depends on PPC_PASEMI - help - Enables support for NAND Flash interface on PA Semi PWRficient - based boards - -config MTD_NAND_TMIO - tristate "NAND Flash device on Toshiba Mobile IO Controller" - depends on MFD_TMIO - help - Support for NAND flash connected to a Toshiba Mobile IO - Controller in some PDAs, including the Sharp SL6000x. - -config MTD_NAND_NANDSIM - tristate "Support for NAND Flash Simulator" - help - The simulator may simulate various NAND flash chips for the - MTD nand layer. - -config MTD_NAND_GPMI_NAND - tristate "GPMI NAND Flash Controller driver" - depends on MXS_DMA - help - Enables NAND Flash support for IMX23, IMX28 or IMX6. - The GPMI controller is very powerful, with the help of BCH - module, it can do the hardware ECC. The GPMI supports several - NAND flashs at the same time. - -config MTD_NAND_BRCMNAND - tristate "Broadcom STB NAND controller" - depends on ARM || ARM64 || MIPS || COMPILE_TEST - depends on HAS_IOMEM - help - Enables the Broadcom NAND controller driver. The controller was - originally designed for Set-Top Box but is used on various BCM7xxx, - BCM3xxx, BCM63xxx, iProc/Cygnus and more. - -config MTD_NAND_BCM47XXNFLASH - tristate "Support for NAND flash on BCM4706 BCMA bus" - depends on BCMA_NFLASH - depends on BCMA - help - BCMA bus can have various flash memories attached, they are - registered by bcma as platform devices. This enables driver for - NAND flash memories. For now only BCM4706 is supported. - -config MTD_NAND_PLATFORM - tristate "Support for generic platform NAND driver" - depends on HAS_IOMEM - help - This implements a generic NAND driver for on-SOC platform - devices. You will need to provide platform-specific functions - via platform_data. - -config MTD_NAND_ORION - tristate "NAND Flash support for Marvell Orion SoC" - depends on PLAT_ORION - help - This enables the NAND flash controller on Orion machines. - - No board specific support is done by this driver, each board - must advertise a platform_device for the driver to attach. - -config MTD_NAND_OXNAS - tristate "NAND Flash support for Oxford Semiconductor SoC" - depends on ARCH_OXNAS || COMPILE_TEST - depends on HAS_IOMEM - help - This enables the NAND flash controller on Oxford Semiconductor SoCs. - -config MTD_NAND_FSL_ELBC - tristate "NAND support for Freescale eLBC controllers" - depends on FSL_SOC - select FSL_LBC - help - Various Freescale chips, including the 8313, include a NAND Flash - Controller Module with built-in hardware ECC capabilities. - Enabling this option will enable you to use this to control - external NAND devices. - -config MTD_NAND_FSL_IFC - tristate "NAND support for Freescale IFC controller" - depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A || COMPILE_TEST - depends on HAS_IOMEM - select FSL_IFC - select MEMORY - help - Various Freescale chips e.g P1010, include a NAND Flash machine - with built-in hardware ECC capabilities. - Enabling this option will enable you to use this to control - external NAND devices. - -config MTD_NAND_FSL_UPM - tristate "Support for NAND on Freescale UPM" - depends on PPC_83xx || PPC_85xx - select FSL_LBC - help - Enables support for NAND Flash chips wired onto Freescale PowerPC - processor localbus with User-Programmable Machine support. - -config MTD_NAND_MPC5121_NFC - tristate "MPC5121 built-in NAND Flash Controller support" - depends on PPC_MPC512x - help - This enables the driver for the NAND flash controller on the - MPC5121 SoC. - -config MTD_NAND_VF610_NFC - tristate "Support for Freescale NFC for VF610/MPC5125" - depends on (SOC_VF610 || COMPILE_TEST) - depends on HAS_IOMEM - help - Enables support for NAND Flash Controller on some Freescale - processors like the VF610, MPC5125, MCF54418 or Kinetis K70. - The driver supports a maximum 2k page size. With 2k pages and - 64 bytes or more of OOB, hardware ECC with up to 32-bit error - correction is supported. Hardware ECC is only enabled through - device tree. - -config MTD_NAND_MXC - tristate "MXC NAND support" - depends on ARCH_MXC || COMPILE_TEST - depends on HAS_IOMEM - help - This enables the driver for the NAND flash controller on the - MXC processors. - -config MTD_NAND_SH_FLCTL - tristate "Support for NAND on Renesas SuperH FLCTL" - depends on SUPERH || COMPILE_TEST - depends on HAS_IOMEM - help - Several Renesas SuperH CPU has FLCTL. This option enables support - for NAND Flash using FLCTL. - -config MTD_NAND_DAVINCI - tristate "Support NAND on DaVinci/Keystone SoC" - depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF) || COMPILE_TEST - depends on HAS_IOMEM - help - Enable the driver for NAND flash chips on Texas Instruments - DaVinci/Keystone processors. - -config MTD_NAND_TXX9NDFMC - tristate "NAND Flash support for TXx9 SoC" - depends on SOC_TX4938 || SOC_TX4939 || COMPILE_TEST - depends on HAS_IOMEM - help - This enables the NAND flash controller on the TXx9 SoCs. - -config MTD_NAND_SOCRATES - tristate "Support for NAND on Socrates board" - depends on SOCRATES - help - Enables support for NAND Flash chips wired onto Socrates board. - -config MTD_NAND_NUC900 - tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards." - depends on ARCH_W90X900 || COMPILE_TEST - depends on HAS_IOMEM - help - This enables the driver for the NAND Flash on evaluation board based - on w90p910 / NUC9xx. - -config MTD_NAND_JZ4740 - tristate "Support for JZ4740 SoC NAND controller" - depends on MACH_JZ4740 || COMPILE_TEST - depends on HAS_IOMEM - help - Enables support for NAND Flash on JZ4740 SoC based boards. - -config MTD_NAND_JZ4780 - tristate "Support for NAND on JZ4780 SoC" - depends on JZ4780_NEMC - help - Enables support for NAND Flash connected to the NEMC on JZ4780 SoC - based boards, using the BCH controller for hardware error correction. - -config MTD_NAND_FSMC - tristate "Support for NAND on ST Micros FSMC" - depends on OF && HAS_IOMEM - depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300 || \ - COMPILE_TEST - help - Enables support for NAND Flash chips on the ST Microelectronics - Flexible Static Memory Controller (FSMC) - -config MTD_NAND_XWAY - bool "Support for NAND on Lantiq XWAY SoC" - depends on LANTIQ && SOC_TYPE_XWAY - help - Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached - to the External Bus Unit (EBU). - -config MTD_NAND_SUNXI - tristate "Support for NAND on Allwinner SoCs" - depends on ARCH_SUNXI || COMPILE_TEST - depends on HAS_IOMEM - help - Enables support for NAND Flash chips on Allwinner SoCs. - -config MTD_NAND_HISI504 - tristate "Support for NAND controller on Hisilicon SoC Hip04" - depends on ARCH_HISI || COMPILE_TEST - depends on HAS_IOMEM - help - Enables support for NAND controller on Hisilicon SoC Hip04. - -config MTD_NAND_QCOM - tristate "Support for NAND on QCOM SoCs" - depends on ARCH_QCOM || COMPILE_TEST - depends on HAS_IOMEM - help - Enables support for NAND flash chips on SoCs containing the EBI2 NAND - controller. This controller is found on IPQ806x SoC. - -config MTD_NAND_MTK - tristate "Support for NAND controller on MTK SoCs" - depends on ARCH_MEDIATEK || COMPILE_TEST - depends on HAS_IOMEM - help - Enables support for NAND controller on MTK SoCs. - This controller is found on mt27xx, mt81xx, mt65xx SoCs. - -config MTD_NAND_TEGRA - tristate "Support for NAND controller on NVIDIA Tegra" - depends on ARCH_TEGRA || COMPILE_TEST - depends on HAS_IOMEM - help - Enables support for NAND flash controller on NVIDIA Tegra SoC. - The driver has been developed and tested on a Tegra 2 SoC. DMA - support, raw read/write page as well as HW ECC read/write page - is supported. Extra OOB bytes when using HW ECC are currently - not supported. - -config MTD_NAND_ROCKCHIP_V6 - tristate "Support for NAND controller V6 on Rockchip SoC" - depends on ARCH_ROCKCHIP - help - Enables support for NAND controller V6 on Rockchip SoC. - -config MTD_NAND_ROCKCHIP_V9 - tristate "Support for NAND controller V9 on Rockchip SoC" - default n - depends on ARCH_ROCKCHIP - help - Enables support for NAND controller V9 on Rockchip - SoC(RK3326,RKPX30). - -endif # MTD_NAND +endif # MTD_RAW_NAND -- Gitblit v1.6.2