From 645e752c5a84baeb21015cdc85fc05b7d16312c8 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Sat, 11 May 2024 01:13:52 +0000
Subject: [PATCH] disable i2c1
---
kernel/arch/arm/boot/dts/qcom-ipq8064.dtsi | 416 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 415 insertions(+), 1 deletions(-)
diff --git a/kernel/arch/arm/boot/dts/qcom-ipq8064.dtsi b/kernel/arch/arm/boot/dts/qcom-ipq8064.dtsi
index 70790ac..dca0ed6 100644
--- a/kernel/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/kernel/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -1,13 +1,17 @@
// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
-#include "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-ipq806x.h>
#include <dt-bindings/clock/qcom,lcc-ipq806x.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
#include <dt-bindings/soc/qcom,gsbi.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
model = "Qualcomm IPQ8064";
compatible = "qcom,ipq8064";
interrupt-parent = <&intc>;
@@ -40,6 +44,11 @@
compatible = "cache";
cache-level = <2>;
};
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x0>;
};
cpu-pmu {
@@ -84,6 +93,12 @@
};
};
+ firmware {
+ scm {
+ compatible = "qcom,scm-ipq806x", "qcom,scm";
+ };
+ };
+
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
@@ -110,10 +125,66 @@
reg = <0x800000 0x4000>;
gpio-controller;
+ gpio-ranges = <&qcom_pinmux 0 0 69>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+
+ pcie0_pins: pcie0_pinmux {
+ mux {
+ pins = "gpio3";
+ function = "pcie1_rst";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ pcie1_pins: pcie1_pinmux {
+ mux {
+ pins = "gpio48";
+ function = "pcie2_rst";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ pcie2_pins: pcie2_pinmux {
+ mux {
+ pins = "gpio63";
+ function = "pcie3_rst";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
+ };
+ };
+
+ leds_pins: leds_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9",
+ "gpio26", "gpio53";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ output-low;
+ };
+ };
+
+ buttons_pins: buttons_pins {
+ mux {
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
};
intc: interrupt-controller@2000000 {
@@ -354,6 +425,13 @@
qcom,controller-type = "pmic-arbiter";
};
+ qfprom: qfprom@700000 {
+ compatible = "qcom,qfprom";
+ reg = <0x00700000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
gcc: clock-controller@900000 {
compatible = "qcom,gcc-ipq8064";
reg = <0x00900000 0x4000>;
@@ -373,5 +451,341 @@
#reset-cells = <1>;
};
+ pcie0: pci@1b500000 {
+ compatible = "qcom,pcie-ipq8064";
+ reg = <0x1b500000 0x1000
+ 0x1b502000 0x80
+ 0x1b600000 0x100
+ 0x0ff00000 0x100000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0x0 0x00000000 0x0fe00000 0x0 0x00010000 /* I/O */
+ 0x82000000 0x0 0x08000000 0x08000000 0x0 0x07e00000>; /* MEM */
+
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc PCIE_A_CLK>,
+ <&gcc PCIE_H_CLK>,
+ <&gcc PCIE_PHY_CLK>,
+ <&gcc PCIE_AUX_CLK>,
+ <&gcc PCIE_ALT_REF_CLK>;
+ clock-names = "core", "iface", "phy", "aux", "ref";
+
+ assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ resets = <&gcc PCIE_ACLK_RESET>,
+ <&gcc PCIE_HCLK_RESET>,
+ <&gcc PCIE_POR_RESET>,
+ <&gcc PCIE_PCI_RESET>,
+ <&gcc PCIE_PHY_RESET>,
+ <&gcc PCIE_EXT_RESET>;
+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+ pinctrl-0 = <&pcie0_pins>;
+ pinctrl-names = "default";
+
+ status = "disabled";
+ perst-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+ };
+
+ pcie1: pci@1b700000 {
+ compatible = "qcom,pcie-ipq8064";
+ reg = <0x1b700000 0x1000
+ 0x1b702000 0x80
+ 0x1b800000 0x100
+ 0x31f00000 0x100000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <1>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0x0 0x00000000 0x31e00000 0x0 0x00010000 /* I/O */
+ 0x82000000 0x0 0x2e000000 0x2e000000 0x0 0x03e00000>; /* MEM */
+
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc PCIE_1_A_CLK>,
+ <&gcc PCIE_1_H_CLK>,
+ <&gcc PCIE_1_PHY_CLK>,
+ <&gcc PCIE_1_AUX_CLK>,
+ <&gcc PCIE_1_ALT_REF_CLK>;
+ clock-names = "core", "iface", "phy", "aux", "ref";
+
+ assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ resets = <&gcc PCIE_1_ACLK_RESET>,
+ <&gcc PCIE_1_HCLK_RESET>,
+ <&gcc PCIE_1_POR_RESET>,
+ <&gcc PCIE_1_PCI_RESET>,
+ <&gcc PCIE_1_PHY_RESET>,
+ <&gcc PCIE_1_EXT_RESET>;
+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+ pinctrl-0 = <&pcie1_pins>;
+ pinctrl-names = "default";
+
+ status = "disabled";
+ perst-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+ };
+
+ pcie2: pci@1b900000 {
+ compatible = "qcom,pcie-ipq8064";
+ reg = <0x1b900000 0x1000
+ 0x1b902000 0x80
+ 0x1ba00000 0x100
+ 0x35f00000 0x100000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <2>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0x0 0x00000000 0x35e00000 0x0 0x00010000 /* I/O */
+ 0x82000000 0x0 0x32000000 0x32000000 0x0 0x03e00000>; /* MEM */
+
+ interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc PCIE_2_A_CLK>,
+ <&gcc PCIE_2_H_CLK>,
+ <&gcc PCIE_2_PHY_CLK>,
+ <&gcc PCIE_2_AUX_CLK>,
+ <&gcc PCIE_2_ALT_REF_CLK>;
+ clock-names = "core", "iface", "phy", "aux", "ref";
+
+ assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ resets = <&gcc PCIE_2_ACLK_RESET>,
+ <&gcc PCIE_2_HCLK_RESET>,
+ <&gcc PCIE_2_POR_RESET>,
+ <&gcc PCIE_2_PCI_RESET>,
+ <&gcc PCIE_2_PHY_RESET>,
+ <&gcc PCIE_2_EXT_RESET>;
+ reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+ pinctrl-0 = <&pcie2_pins>;
+ pinctrl-names = "default";
+
+ status = "disabled";
+ perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
+ };
+
+ nss_common: syscon@03000000 {
+ compatible = "syscon";
+ reg = <0x03000000 0x0000FFFF>;
+ };
+
+ qsgmii_csr: syscon@1bb00000 {
+ compatible = "syscon";
+ reg = <0x1bb00000 0x000001FF>;
+ };
+
+ stmmac_axi_setup: stmmac-axi-config {
+ snps,wr_osr_lmt = <7>;
+ snps,rd_osr_lmt = <7>;
+ snps,blen = <16 0 0 0 0 0 0>;
+ };
+
+ gmac0: ethernet@37000000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac";
+ reg = <0x37000000 0x200000>;
+ interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,pbl = <32>;
+ snps,aal = <1>;
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE1_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE1_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
+ gmac1: ethernet@37200000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac";
+ reg = <0x37200000 0x200000>;
+ interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,pbl = <32>;
+ snps,aal = <1>;
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE2_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE2_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
+ gmac2: ethernet@37400000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac";
+ reg = <0x37400000 0x200000>;
+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,pbl = <32>;
+ snps,aal = <1>;
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE3_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE3_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
+ gmac3: ethernet@37600000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac";
+ reg = <0x37600000 0x200000>;
+ interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,pbl = <32>;
+ snps,aal = <1>;
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE4_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE4_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
+ vsdcc_fixed: vsdcc-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "SDCC Power";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ sdcc1bam:dma@12402000 {
+ compatible = "qcom,bam-v1.3.0";
+ reg = <0x12402000 0x8000>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc SDC1_H_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ };
+
+ sdcc3bam:dma@12182000 {
+ compatible = "qcom,bam-v1.3.0";
+ reg = <0x12182000 0x8000>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc SDC3_H_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ };
+
+ amba {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sdcc@12400000 {
+ status = "disabled";
+ compatible = "arm,pl18x", "arm,primecell";
+ arm,primecell-periphid = <0x00051180>;
+ reg = <0x12400000 0x2000>;
+ interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cmd_irq";
+ clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+ clock-names = "mclk", "apb_pclk";
+ bus-width = <8>;
+ max-frequency = <96000000>;
+ non-removable;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ vmmc-supply = <&vsdcc_fixed>;
+ dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+ dma-names = "tx", "rx";
+ };
+
+ sdcc@12180000 {
+ compatible = "arm,pl18x", "arm,primecell";
+ arm,primecell-periphid = <0x00051180>;
+ status = "disabled";
+ reg = <0x12180000 0x2000>;
+ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cmd_irq";
+ clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+ clock-names = "mclk", "apb_pclk";
+ bus-width = <8>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <192000000>;
+ #mmc-ddr-1_8v;
+ sd-uhs-sdr104;
+ sd-uhs-ddr50;
+ vqmmc-supply = <&vsdcc_fixed>;
+ dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+ dma-names = "tx", "rx";
+ };
+ };
};
};
--
Gitblit v1.6.2