From 50a212ec906f7524620675f0c57357691c26c81f Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Wed, 16 Oct 2024 01:20:19 +0000
Subject: [PATCH] 修改GPIO导出默认初始值

---
 kernel/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi |   53 +++++------------------------------------------------
 1 files changed, 5 insertions(+), 48 deletions(-)

diff --git a/kernel/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi b/kernel/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi
index d2a2eb8..1a9926d 100644
--- a/kernel/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi
+++ b/kernel/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi
@@ -54,7 +54,7 @@
 		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
-		/* TODO: backlight uses axp gpio1 as enable pin */
+		enable-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>; /* AXP GPIO1 */
 	};
 
 	chosen {
@@ -63,8 +63,6 @@
 };
 
 &codec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&codec_pa_pin>;
 	allwinner,pa-gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */
 	status = "okay";
 };
@@ -96,8 +94,6 @@
 		reg = <0x40>;
 		interrupt-parent = <&pio>;
 		interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; /* EINT11 (PG11) */
-		pinctrl-names = "default";
-		pinctrl-0 = <&ts_power_pin>;
 		power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
 		/* Tablet dts must provide reg and compatible */
 		status = "disabled";
@@ -125,7 +121,7 @@
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_vcc3v0>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
@@ -134,43 +130,6 @@
 
 &otg_sram {
 	status = "okay";
-};
-
-&pio {
-	codec_pa_pin: codec_pa_pin@0 {
-		pins = "PG10";
-		function = "gpio_out";
-	};
-
-	mmc0_cd_pin: mmc0_cd_pin@0 {
-		pins = "PG0";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	ts_power_pin: ts_power_pin {
-		pins = "PB3";
-		function = "gpio_out";
-		drive-strength = <10>;
-		bias-disable;
-	};
-
-	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-		bias-pull-down;
-	};
-
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		pins = "PG2";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb0_vbus_pin_a: usb0_vbus_pin@0 {
-		pins = "PG12";
-		function = "gpio_out";
-	};
 };
 
 &reg_dcdc2 {
@@ -211,7 +170,7 @@
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_b>;
+	pinctrl-0 = <&uart1_pg_pins>;
 	status = "okay";
 };
 
@@ -225,10 +184,8 @@
 };
 
 &usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
-	usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+	usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
+	usb0_vbus_det-gpios = <&pio 6 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PG1 */
 	usb0_vbus_power-supply = <&usb_power_supply>;
 	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_ldo3>;

--
Gitblit v1.6.2