From 2f7c68cb55ecb7331f2381deb497c27155f32faf Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Wed, 03 Jan 2024 09:43:39 +0000
Subject: [PATCH] update kernel to 5.10.198
---
kernel/drivers/tty/serial/qcom_geni_serial.c | 30 +++++++++++++++++++++---------
1 files changed, 21 insertions(+), 9 deletions(-)
diff --git a/kernel/drivers/tty/serial/qcom_geni_serial.c b/kernel/drivers/tty/serial/qcom_geni_serial.c
index 0d85b55..7caba23 100644
--- a/kernel/drivers/tty/serial/qcom_geni_serial.c
+++ b/kernel/drivers/tty/serial/qcom_geni_serial.c
@@ -125,6 +125,7 @@
u32 tx_fifo_width;
u32 rx_fifo_depth;
bool setup;
+ unsigned long clk_rate;
int (*handle_rx)(struct uart_port *uport, u32 bytes, bool drop);
unsigned int baud;
void *rx_fifo;
@@ -866,9 +867,10 @@
return IRQ_HANDLED;
}
-static void get_tx_fifo_size(struct qcom_geni_serial_port *port)
+static int setup_fifos(struct qcom_geni_serial_port *port)
{
struct uart_port *uport;
+ u32 old_rx_fifo_depth = port->rx_fifo_depth;
uport = &port->uport;
port->tx_fifo_depth = geni_se_get_tx_fifo_depth(&port->se);
@@ -876,6 +878,16 @@
port->rx_fifo_depth = geni_se_get_rx_fifo_depth(&port->se);
uport->fifosize =
(port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE;
+
+ if (port->rx_fifo && (old_rx_fifo_depth != port->rx_fifo_depth) && port->rx_fifo_depth) {
+ port->rx_fifo = devm_krealloc(uport->dev, port->rx_fifo,
+ port->rx_fifo_depth * sizeof(u32),
+ GFP_KERNEL);
+ if (!port->rx_fifo)
+ return -ENOMEM;
+ }
+
+ return 0;
}
@@ -890,6 +902,7 @@
u32 rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT;
u32 proto;
u32 pin_swap;
+ int ret;
proto = geni_se_read_proto(&port->se);
if (proto != GENI_SE_UART) {
@@ -899,7 +912,9 @@
qcom_geni_serial_stop_rx(uport);
- get_tx_fifo_size(port);
+ ret = setup_fifos(port);
+ if (ret)
+ return ret;
writel(rxstale, uport->membase + SE_UART_RX_STALE_CNT);
@@ -1008,6 +1023,7 @@
goto out_restart_rx;
uport->uartclk = clk_rate;
+ port->clk_rate = clk_rate;
dev_pm_opp_set_rate(uport->dev, clk_rate);
ser_clk_cfg = SER_CLK_EN;
ser_clk_cfg |= clk_div << CLK_DIV_SHFT;
@@ -1291,10 +1307,13 @@
if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF) {
geni_icc_enable(&port->se);
+ if (port->clk_rate)
+ dev_pm_opp_set_rate(uport->dev, port->clk_rate);
geni_se_resources_on(&port->se);
} else if (new_state == UART_PM_STATE_OFF &&
old_state == UART_PM_STATE_ON) {
geni_se_resources_off(&port->se);
+ dev_pm_opp_set_rate(uport->dev, 0);
geni_icc_disable(&port->se);
}
}
@@ -1453,13 +1472,6 @@
uart_remove_one_port(drv, uport);
goto err;
}
-
- /*
- * Set pm_runtime status as ACTIVE so that wakeup_irq gets
- * enabled/disabled from dev_pm_arm_wake_irq during system
- * suspend/resume respectively.
- */
- pm_runtime_set_active(&pdev->dev);
if (port->wakeup_irq > 0) {
device_init_wakeup(&pdev->dev, true);
--
Gitblit v1.6.2