From 297b60346df8beafee954a0fd7c2d64f33f3b9bc Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Sat, 11 May 2024 01:44:05 +0000
Subject: [PATCH] rtl8211F_led_control
---
kernel/include/uapi/linux/usb/ch9.h | 51 +++++++++++++++++++++++++--------------------------
1 files changed, 25 insertions(+), 26 deletions(-)
diff --git a/kernel/include/uapi/linux/usb/ch9.h b/kernel/include/uapi/linux/usb/ch9.h
index 9fa1a51..17ce561 100644
--- a/kernel/include/uapi/linux/usb/ch9.h
+++ b/kernel/include/uapi/linux/usb/ch9.h
@@ -138,11 +138,11 @@
* Test Mode Selectors
* See USB 2.0 spec Table 9-7
*/
-#define TEST_J 1
-#define TEST_K 2
-#define TEST_SE0_NAK 3
-#define TEST_PACKET 4
-#define TEST_FORCE_EN 5
+#define USB_TEST_J 1
+#define USB_TEST_K 2
+#define USB_TEST_SE0_NAK 3
+#define USB_TEST_PACKET 4
+#define USB_TEST_FORCE_ENABLE 5
/* Status Type */
#define USB_STATUS_TYPE_STANDARD 0
@@ -326,6 +326,10 @@
#define USB_CLASS_CONTENT_SEC 0x0d /* content security */
#define USB_CLASS_VIDEO 0x0e
#define USB_CLASS_WIRELESS_CONTROLLER 0xe0
+#define USB_CLASS_PERSONAL_HEALTHCARE 0x0f
+#define USB_CLASS_AUDIO_VIDEO 0x10
+#define USB_CLASS_BILLBOARD 0x11
+#define USB_CLASS_USB_TYPE_C_BRIDGE 0x12
#define USB_CLASS_MISC 0xef
#define USB_CLASS_APP_SPEC 0xfe
#define USB_CLASS_VENDOR_SPEC 0xff
@@ -897,6 +901,8 @@
#define USB_BESL_SUPPORT (1 << 2) /* supports BESL */
#define USB_BESL_BASELINE_VALID (1 << 3) /* Baseline BESL valid*/
#define USB_BESL_DEEP_VALID (1 << 4) /* Deep BESL valid */
+#define USB_SET_BESL_BASELINE(p) (((p) & 0xf) << 8)
+#define USB_SET_BESL_DEEP(p) (((p) & 0xf) << 12)
#define USB_GET_BESL_BASELINE(p) (((p) & (0xf << 8)) >> 8)
#define USB_GET_BESL_DEEP(p) (((p) & (0xf << 12)) >> 12)
} __attribute__((packed));
@@ -962,9 +968,22 @@
__le32 bmSublinkSpeedAttr[1]; /* list of sublink speed attrib entries */
#define USB_SSP_SUBLINK_SPEED_SSID (0xf) /* sublink speed ID */
#define USB_SSP_SUBLINK_SPEED_LSE (0x3 << 4) /* Lanespeed exponent */
+#define USB_SSP_SUBLINK_SPEED_LSE_BPS 0
+#define USB_SSP_SUBLINK_SPEED_LSE_KBPS 1
+#define USB_SSP_SUBLINK_SPEED_LSE_MBPS 2
+#define USB_SSP_SUBLINK_SPEED_LSE_GBPS 3
+
#define USB_SSP_SUBLINK_SPEED_ST (0x3 << 6) /* Sublink type */
+#define USB_SSP_SUBLINK_SPEED_ST_SYM_RX 0
+#define USB_SSP_SUBLINK_SPEED_ST_ASYM_RX 1
+#define USB_SSP_SUBLINK_SPEED_ST_SYM_TX 2
+#define USB_SSP_SUBLINK_SPEED_ST_ASYM_TX 3
+
#define USB_SSP_SUBLINK_SPEED_RSVD (0x3f << 8) /* Reserved */
#define USB_SSP_SUBLINK_SPEED_LP (0x3 << 14) /* Link protocol */
+#define USB_SSP_SUBLINK_SPEED_LP_SS 0
+#define USB_SSP_SUBLINK_SPEED_LP_SSP 1
+
#define USB_SSP_SUBLINK_SPEED_LSM (0xff << 16) /* Lanespeed mantissa */
} __attribute__((packed));
@@ -1083,26 +1102,6 @@
* (SSAC) specified in bmAttributes[4:0]. SSAC is zero-based
*/
#define USB_DT_USB_SSP_CAP_SIZE(ssac) (12 + (ssac + 1) * 4)
-
-/*
- * Configuration Summary descriptors: Defines a list of device preferred
- * configurations. This descriptor may be used by Host software to decide
- * which Configuration to use to obtain the desired functionality.
- */
-#define USB_CAP_TYPE_CONFIG_SUMMARY 0x10
-#define USB_CONFIG_SUMMARY_DESC_REV 0x100
-
-struct usb_config_summary_descriptor {
- __u8 bLength;
- __u8 bDescriptorType;
- __u8 bDevCapabilityType;
- __u16 bcdVersion;
- __u8 bClass;
- __u8 bSubClass;
- __u8 bProtocol;
- __u8 bConfigurationCount;
- __u8 bConfigurationIndex[];
-} __attribute__((packed));
/*-------------------------------------------------------------------------*/
@@ -1243,7 +1242,7 @@
* As per USB compliance update, a device that is actively drawing
* more than 100mA from USB must report itself as bus-powered in
* the GetStatus(DEVICE) call.
- * http://compliance.usb.org/index.asp?UpdateFile=Electrical&Format=Standard#34
+ * https://compliance.usb.org/index.asp?UpdateFile=Electrical&Format=Standard#34
*/
#define USB_SELF_POWER_VBUS_MAX_DRAW 100
--
Gitblit v1.6.2