From 23fa18eaa71266feff7ba8d83022d9e1cc83c65a Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Fri, 10 May 2024 07:42:03 +0000
Subject: [PATCH] disable pwm7
---
kernel/include/linux/qcom-geni-se.h | 65 ++++++++++++++++++++++++++------
1 files changed, 53 insertions(+), 12 deletions(-)
diff --git a/kernel/include/linux/qcom-geni-se.h b/kernel/include/linux/qcom-geni-se.h
index 5d61449..964cfe6 100644
--- a/kernel/include/linux/qcom-geni-se.h
+++ b/kernel/include/linux/qcom-geni-se.h
@@ -1,10 +1,12 @@
-/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright (c) 2017-2018, The Linux Foundation. All rights reserved.
*/
#ifndef _LINUX_QCOM_GENI_SE
#define _LINUX_QCOM_GENI_SE
+
+#include <linux/interconnect.h>
/* Transfer mode supported by GENI Serial Engines */
enum geni_se_xfer_mode {
@@ -25,6 +27,17 @@
struct geni_wrapper;
struct clk;
+enum geni_icc_path_index {
+ GENI_TO_CORE,
+ CPU_TO_GENI,
+ GENI_TO_DDR
+};
+
+struct geni_icc_path {
+ struct icc_path *path;
+ unsigned int avg_bw;
+};
+
/**
* struct geni_se - GENI Serial Engine
* @base: Base Address of the Serial Engine's register block
@@ -33,6 +46,9 @@
* @clk: Handle to the core serial engine clock
* @num_clk_levels: Number of valid clock levels in clk_perf_tbl
* @clk_perf_tbl: Table of clock frequency input to serial engine clock
+ * @icc_paths: Array of ICC paths for SE
+ * @opp_table: Pointer to the OPP table
+ * @has_opp_table: Specifies if the SE has an OPP table
*/
struct geni_se {
void __iomem *base;
@@ -41,6 +57,9 @@
struct clk *clk;
unsigned int num_clk_levels;
unsigned long *clk_perf_tbl;
+ struct geni_icc_path icc_paths[3];
+ struct opp_table *opp_table;
+ bool has_opp_table;
};
/* Common SE registers */
@@ -225,18 +244,31 @@
#define HW_VER_MINOR_SHFT 16
#define HW_VER_STEP_MASK GENMASK(15, 0)
+#define GENI_SE_VERSION_MAJOR(ver) ((ver & HW_VER_MAJOR_MASK) >> HW_VER_MAJOR_SHFT)
+#define GENI_SE_VERSION_MINOR(ver) ((ver & HW_VER_MINOR_MASK) >> HW_VER_MINOR_SHFT)
+#define GENI_SE_VERSION_STEP(ver) (ver & HW_VER_STEP_MASK)
+
+/* QUP SE VERSION value for major number 2 and minor number 5 */
+#define QUP_SE_VERSION_2_5 0x20050000
+
+/*
+ * Define bandwidth thresholds that cause the underlying Core 2X interconnect
+ * clock to run at the named frequency. These baseline values are recommended
+ * by the hardware team, and are not dynamically scaled with GENI bandwidth
+ * beyond basic on/off.
+ */
+#define CORE_2X_19_2_MHZ 960
+#define CORE_2X_50_MHZ 2500
+#define CORE_2X_100_MHZ 5000
+#define CORE_2X_150_MHZ 7500
+#define CORE_2X_200_MHZ 10000
+#define CORE_2X_236_MHZ 16383
+
+#define GENI_DEFAULT_BW Bps_to_icc(1000)
+
#if IS_ENABLED(CONFIG_QCOM_GENI_SE)
u32 geni_se_get_qup_hw_version(struct geni_se *se);
-
-#define geni_se_get_wrapper_version(se, major, minor, step) do { \
- u32 ver; \
-\
- ver = geni_se_get_qup_hw_version(se); \
- major = (ver & HW_VER_MAJOR_MASK) >> HW_VER_MAJOR_SHFT; \
- minor = (ver & HW_VER_MINOR_MASK) >> HW_VER_MINOR_SHFT; \
- step = version & HW_VER_STEP_MASK; \
-} while (0)
/**
* geni_se_read_proto() - Read the protocol configured for a serial engine
@@ -267,7 +299,7 @@
u32 m_cmd;
m_cmd = (cmd << M_OPCODE_SHFT) | (params & M_PARAMS_MSK);
- writel_relaxed(m_cmd, se->base + SE_GENI_M_CMD0);
+ writel(m_cmd, se->base + SE_GENI_M_CMD0);
}
/**
@@ -287,7 +319,7 @@
s_cmd &= ~(S_OPCODE_MSK | S_PARAMS_MSK);
s_cmd |= (cmd << S_OPCODE_SHFT);
s_cmd |= (params & S_PARAMS_MSK);
- writel_relaxed(s_cmd, se->base + SE_GENI_S_CMD0);
+ writel(s_cmd, se->base + SE_GENI_S_CMD0);
}
/**
@@ -421,5 +453,14 @@
void geni_se_tx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len);
void geni_se_rx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len);
+
+int geni_icc_get(struct geni_se *se, const char *icc_ddr);
+
+int geni_icc_set_bw(struct geni_se *se);
+void geni_icc_set_tag(struct geni_se *se, u32 tag);
+
+int geni_icc_enable(struct geni_se *se);
+
+int geni_icc_disable(struct geni_se *se);
#endif
#endif
--
Gitblit v1.6.2