From 08f87f769b595151be1afeff53e144f543faa614 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Wed, 06 Dec 2023 09:51:13 +0000
Subject: [PATCH] add dts config
---
kernel/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 29 +++++++++++++++++++----------
1 files changed, 19 insertions(+), 10 deletions(-)
diff --git a/kernel/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/kernel/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
index 14062b4..68ecd0f 100644
--- a/kernel/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
+++ b/kernel/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
@@ -2,7 +2,7 @@
/*
* dts file for Xilinx ZynqMP ZCU100 revC
*
- * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ * (C) Copyright 2016 - 2019, Xilinx, Inc.
*
* Michal Simek <michal.simek@xilinx.com>
* Nathalie Chan King Choy
@@ -11,7 +11,7 @@
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
@@ -49,34 +49,34 @@
label = "sw4";
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
- gpio-key,wakeup;
+ wakeup-source;
autorepeat;
};
};
leds {
compatible = "gpio-leds";
- ds2 {
+ led-ds2 {
label = "ds2";
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
- ds3 {
+ led-ds3 {
label = "ds3";
gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tx"; /* WLAN tx */
default-state = "off";
};
- ds4 {
+ led-ds4 {
label = "ds4";
gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0rx"; /* WLAN rx */
default-state = "off";
};
- ds5 {
+ led-ds5 {
label = "ds5";
gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "bluetooth-power";
@@ -102,6 +102,11 @@
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */
post-power-on-delay-ms = <10>;
+ };
+
+ ina226 {
+ compatible = "iio-hwmon";
+ io-channels = <&u35 0>, <&u35 1>, <&u35 2>, <&u35 3>;
};
};
@@ -181,7 +186,7 @@
compatible = "ti,tps65086";
reg = <0x5e>;
interrupt-parent = <&gpio>;
- interrupts = <77 GPIO_ACTIVE_LOW>;
+ interrupts = <77 IRQ_TYPE_LEVEL_LOW>;
#gpio-cells = <2>;
gpio-controller;
};
@@ -191,8 +196,9 @@
#size-cells = <0>;
reg = <5>;
/* PS_PMBUS */
- ina226@40 { /* u35 */
+ u35: ina226@40 { /* u35 */
compatible = "ti,ina226";
+ #io-channel-cells = <1>;
reg = <0x40>;
shunt-resistor = <10000>;
/* MIO31 is alert which should be routed to PMUFW */
@@ -226,7 +232,6 @@
&sdhci0 {
status = "okay";
no-1-8-v;
- broken-cd; /* CD has to be enabled by default */
disable-wp;
};
@@ -251,11 +256,13 @@
&spi0 { /* Low Speed connector */
status = "okay";
label = "LS-SPI0";
+ num-cs = <1>;
};
&spi1 { /* High Speed connector */
status = "okay";
label = "HS-SPI1";
+ num-cs = <1>;
};
&uart0 {
@@ -274,11 +281,13 @@
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
+ dr_mode = "peripheral";
};
/* ULPI SMSC USB3320 */
&usb1 {
status = "okay";
+ dr_mode = "host";
};
&watchdog0 {
--
Gitblit v1.6.2