From 08f87f769b595151be1afeff53e144f543faa614 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Wed, 06 Dec 2023 09:51:13 +0000
Subject: [PATCH] add dts config
---
kernel/arch/arm/boot/dts/ste-dbx5x0.dtsi | 481 ++++++++++++++++++++++-------------------------------
1 files changed, 199 insertions(+), 282 deletions(-)
diff --git a/kernel/arch/arm/boot/dts/ste-dbx5x0.dtsi b/kernel/arch/arm/boot/dts/ste-dbx5x0.dtsi
index 9867677..05fd544 100644
--- a/kernel/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/kernel/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -1,12 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright 2012 Linaro Ltd
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
*/
#include <dt-bindings/interrupt-controller/irq.h>
@@ -14,10 +8,31 @@
#include <dt-bindings/mfd/dbx500-prcmu.h>
#include <dt-bindings/arm/ux500_pm_domains.h>
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clock/ste-ab8500.h>
-#include "skeleton.dtsi"
+#include <dt-bindings/thermal/thermal.h>
/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* This stablilizes the device enumeration */
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ i2c3 = &i2c3;
+ i2c4 = &i2c4;
+ spi0 = &spi0;
+ spi1 = &spi1;
+ spi2 = &spi2;
+ spi3 = &spi3;
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ };
+
+ chosen {
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
@@ -37,14 +52,10 @@
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <0x300>;
- /* cpufreq controls */
- operating-points = <998400 0
- 800000 0
- 400000 0
- 200000 0>;
clocks = <&prcmu_clk PRCMU_ARMSS>;
clock-names = "cpu";
clock-latency = <20000>;
+ #cooling-cells = <2>;
};
CPU1: cpu@301 {
device_type = "cpu";
@@ -53,10 +64,47 @@
};
};
+ thermal-zones {
+ /*
+ * Thermal zone for the SoC, using the thermal sensor in the
+ * PRCMU for temperature and the cpufreq driver for passive
+ * cooling.
+ */
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <250>;
+ /*
+ * This sensor fires interrupts to update the thermal
+ * zone, so no polling is needed.
+ */
+ polling-delay = <0>;
+
+ thermal-sensors = <&thermal>;
+
+ trips {
+ cpu_alert: cpu-alert {
+ temperature = <70000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu-crit {
+ temperature = <85000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ trip = <&cpu_alert>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ contribution = <100>;
+ };
+ };
+ };
+
soc {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "stericsson,db8500";
+ compatible = "stericsson,db8500", "simple-bus";
interrupt-parent = <&intc>;
ranges;
@@ -67,9 +115,11 @@
clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
clock-names = "apb_pclk", "atclk";
cpu = <&CPU0>;
- port {
- ptm0_out_port: endpoint {
- remote-endpoint = <&funnel_in_port0>;
+ out-ports {
+ port {
+ ptm0_out_port: endpoint {
+ remote-endpoint = <&funnel_in_port0>;
+ };
};
};
};
@@ -81,45 +131,44 @@
clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
clock-names = "apb_pclk", "atclk";
cpu = <&CPU1>;
- port {
- ptm1_out_port: endpoint {
- remote-endpoint = <&funnel_in_port1>;
+ out-ports {
+ port {
+ ptm1_out_port: endpoint {
+ remote-endpoint = <&funnel_in_port1>;
+ };
};
};
};
funnel@801a6000 {
- compatible = "arm,coresight-funnel", "arm,primecell";
+ compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
reg = <0x801a6000 0x1000>;
clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
clock-names = "apb_pclk", "atclk";
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* funnel output ports */
- port@0 {
- reg = <0>;
+ out-ports {
+ port {
funnel_out_port: endpoint {
remote-endpoint =
<&replicator_in_port0>;
};
};
+ };
- /* funnel input ports */
- port@1 {
+ in-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
reg = <0>;
funnel_in_port0: endpoint {
- slave-mode;
remote-endpoint = <&ptm0_out_port>;
};
};
- port@2 {
+ port@1 {
reg = <1>;
funnel_in_port1: endpoint {
- slave-mode;
remote-endpoint = <&ptm1_out_port>;
};
};
@@ -127,15 +176,14 @@
};
replicator {
- compatible = "arm,coresight-replicator";
+ compatible = "arm,coresight-static-replicator";
clocks = <&prcmu_clk PRCMU_APEATCLK>;
clock-names = "atclk";
- ports {
+ out-ports {
#address-cells = <1>;
#size-cells = <0>;
- /* replicator output ports */
port@0 {
reg = <0>;
replicator_out_port0: endpoint {
@@ -148,12 +196,11 @@
remote-endpoint = <&etb_in_port>;
};
};
+ };
- /* replicator input port */
- port@2 {
- reg = <0>;
+ in-ports {
+ port {
replicator_in_port0: endpoint {
- slave-mode;
remote-endpoint = <&funnel_out_port>;
};
};
@@ -166,10 +213,11 @@
clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
clock-names = "apb_pclk", "atclk";
- port {
- tpiu_in_port: endpoint {
- slave-mode;
- remote-endpoint = <&replicator_out_port0>;
+ in-ports {
+ port {
+ tpiu_in_port: endpoint {
+ remote-endpoint = <&replicator_out_port0>;
+ };
};
};
};
@@ -180,10 +228,11 @@
clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
clock-names = "apb_pclk", "atclk";
- port {
- etb_in_port: endpoint {
- slave-mode;
- remote-endpoint = <&replicator_out_port1>;
+ in-ports {
+ port {
+ etb_in_port: endpoint {
+ remote-endpoint = <&replicator_out_port1>;
+ };
};
};
};
@@ -211,7 +260,7 @@
reg = <0x80150000 0x2000>;
};
- L2: l2-cache {
+ L2: cache-controller {
compatible = "arm,pl310-cache";
reg = <0xa0412000 0x1000>;
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
@@ -286,7 +335,7 @@
};
rtc@80154000 {
- compatible = "arm,rtc-pl031", "arm,primecell";
+ compatible = "arm,pl031", "arm,primecell";
reg = <0x80154000 0x1000>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
@@ -487,7 +536,7 @@
};
prcmu: prcmu@80157000 {
- compatible = "stericsson,db8500-prcmu";
+ compatible = "stericsson,db8500-prcmu", "syscon";
reg = <0x80157000 0x2000>, <0x801b0000 0x8000>, <0x801b8000 0x1000>;
reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm";
interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
@@ -502,13 +551,14 @@
reg = <0x80157450 0xC>;
};
- thermal@801573c0 {
+ thermal: thermal@801573c0 {
compatible = "stericsson,db8500-thermal";
reg = <0x801573c0 0x40>;
+ interrupt-parent = <&prcmu>;
interrupts = <21 IRQ_TYPE_LEVEL_HIGH>,
<22 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "IRQ_HOTMON_LOW", "IRQ_HOTMON_HIGH";
- status = "disabled";
+ #thermal-sensor-cells = <0>;
};
db8500-prcmu-regulators {
@@ -597,209 +647,9 @@
db8500_esram34_ret_reg: db8500_esram34_ret {
};
};
-
- ab8500 {
- compatible = "stericsson,ab8500";
- interrupt-parent = <&intc>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- ab8500_clock: clock-controller {
- compatible = "stericsson,ab8500-clk";
- #clock-cells = <1>;
- };
-
- ab8500_gpio: ab8500-gpio {
- compatible = "stericsson,ab8500-gpio";
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- ab8500-rtc {
- compatible = "stericsson,ab8500-rtc";
- interrupts = <17 IRQ_TYPE_LEVEL_HIGH
- 18 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "60S", "ALARM";
- };
-
- ab8500-gpadc {
- compatible = "stericsson,ab8500-gpadc";
- interrupts = <32 IRQ_TYPE_LEVEL_HIGH
- 39 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "HW_CONV_END", "SW_CONV_END";
- vddadc-supply = <&ab8500_ldo_tvout_reg>;
- };
-
- ab8500_battery: ab8500_battery {
- stericsson,battery-type = "LIPO";
- thermistor-on-batctrl;
- };
-
- ab8500_fg {
- compatible = "stericsson,ab8500-fg";
- battery = <&ab8500_battery>;
- };
-
- ab8500_btemp {
- compatible = "stericsson,ab8500-btemp";
- battery = <&ab8500_battery>;
- };
-
- ab8500_charger {
- compatible = "stericsson,ab8500-charger";
- battery = <&ab8500_battery>;
- vddadc-supply = <&ab8500_ldo_tvout_reg>;
- };
-
- ab8500_chargalg {
- compatible = "stericsson,ab8500-chargalg";
- battery = <&ab8500_battery>;
- };
-
- ab8500_usb {
- compatible = "stericsson,ab8500-usb";
- interrupts = < 90 IRQ_TYPE_LEVEL_HIGH
- 96 IRQ_TYPE_LEVEL_HIGH
- 14 IRQ_TYPE_LEVEL_HIGH
- 15 IRQ_TYPE_LEVEL_HIGH
- 79 IRQ_TYPE_LEVEL_HIGH
- 74 IRQ_TYPE_LEVEL_HIGH
- 75 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "ID_WAKEUP_R",
- "ID_WAKEUP_F",
- "VBUS_DET_F",
- "VBUS_DET_R",
- "USB_LINK_STATUS",
- "USB_ADP_PROBE_PLUG",
- "USB_ADP_PROBE_UNPLUG";
- vddulpivio18-supply = <&ab8500_ldo_intcore_reg>;
- v-ape-supply = <&db8500_vape_reg>;
- musb_1v8-supply = <&db8500_vsmps2_reg>;
- clocks = <&prcmu_clk PRCMU_SYSCLK>;
- clock-names = "sysclk";
- };
-
- ab8500-ponkey {
- compatible = "stericsson,ab8500-poweron-key";
- interrupts = <6 IRQ_TYPE_LEVEL_HIGH
- 7 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
- };
-
- ab8500-sysctrl {
- compatible = "stericsson,ab8500-sysctrl";
- };
-
- ab8500-pwm {
- compatible = "stericsson,ab8500-pwm";
- clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
- clock-names = "intclk";
- };
-
- ab8500-debugfs {
- compatible = "stericsson,ab8500-debug";
- };
-
- codec: ab8500-codec {
- compatible = "stericsson,ab8500-codec";
-
- V-AUD-supply = <&ab8500_ldo_audio_reg>;
- V-AMIC1-supply = <&ab8500_ldo_anamic1_reg>;
- V-AMIC2-supply = <&ab8500_ldo_anamic2_reg>;
- V-DMIC-supply = <&ab8500_ldo_dmic_reg>;
-
- clocks = <&ab8500_clock AB8500_SYSCLK_AUDIO>;
- clock-names = "audioclk";
-
- stericsson,earpeice-cmv = <950>; /* Units in mV. */
- };
-
- ext_regulators: ab8500-ext-regulators {
- compatible = "stericsson,ab8500-ext-regulator";
-
- ab8500_ext1_reg: ab8500_ext1 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ab8500_ext2_reg: ab8500_ext2 {
- regulator-min-microvolt = <1360000>;
- regulator-max-microvolt = <1360000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ab8500_ext3_reg: ab8500_ext3 {
- regulator-min-microvolt = <3400000>;
- regulator-max-microvolt = <3400000>;
- regulator-boot-on;
- };
- };
-
- ab8500-regulators {
- compatible = "stericsson,ab8500-regulator";
- vin-supply = <&ab8500_ext3_reg>;
-
- // supplies to the display/camera
- ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2900000>;
- regulator-boot-on;
- /* BUG: If turned off MMC will be affected. */
- regulator-always-on;
- };
-
- // supplies to the on-board eMMC
- ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <3300000>;
- };
-
- // supply for VAUX3; SDcard slots
- ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <3300000>;
- };
-
- // supply for v-intcore12; VINTCORE12 LDO
- ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
- };
-
- // supply for tvout; gpadc; TVOUT LDO
- ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
- };
-
- // supply for ab8500-usb; USB LDO
- ab8500_ldo_usb_reg: ab8500_ldo_usb {
- };
-
- // supply for ab8500-vaudio; VAUDIO LDO
- ab8500_ldo_audio_reg: ab8500_ldo_audio {
- };
-
- // supply for v-anamic1 VAMIC1 LDO
- ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
- };
-
- // supply for v-amic2; VAMIC2 LDO; reuse constants for AMIC1
- ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
- };
-
- // supply for v-dmic; VDMIC LDO
- ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
- };
-
- // supply for U8500 CSI/DSI; VANA LDO
- ab8500_ldo_ana_reg: ab8500_ldo_ana {
- };
- };
- };
};
- i2c@80004000 {
+ i2c0: i2c@80004000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80004000 0x1000>;
interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
@@ -812,9 +662,11 @@
clocks = <&prcc_kclk 3 3>, <&prcc_pclk 3 3>;
clock-names = "i2cclk", "apb_pclk";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
- i2c@80122000 {
+ i2c1: i2c@80122000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80122000 0x1000>;
interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
@@ -828,9 +680,11 @@
clocks = <&prcc_kclk 1 2>, <&prcc_pclk 1 2>;
clock-names = "i2cclk", "apb_pclk";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
- i2c@80128000 {
+ i2c2: i2c@80128000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80128000 0x1000>;
interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
@@ -844,9 +698,11 @@
clocks = <&prcc_kclk 1 6>, <&prcc_pclk 1 6>;
clock-names = "i2cclk", "apb_pclk";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
- i2c@80110000 {
+ i2c3: i2c@80110000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80110000 0x1000>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
@@ -860,9 +716,11 @@
clocks = <&prcc_kclk 2 0>, <&prcc_pclk 2 0>;
clock-names = "i2cclk", "apb_pclk";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
- i2c@8012a000 {
+ i2c4: i2c@8012a000 {
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x8012a000 0x1000>;
interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
@@ -876,9 +734,11 @@
clocks = <&prcc_kclk 1 9>, <&prcc_pclk 1 10>;
clock-names = "i2cclk", "apb_pclk";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
- spi@80002000 {
+ ssp0: spi@80002000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x80002000 0x1000>;
interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
@@ -890,9 +750,11 @@
<&dma 8 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
- spi@80003000 {
+ ssp1: spi@80003000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x80003000 0x1000>;
interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
@@ -904,9 +766,11 @@
<&dma 9 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
- spi@8011a000 {
+ spi0: spi@8011a000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x8011a000 0x1000>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
@@ -919,9 +783,11 @@
<&dma 0 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
- spi@80112000 {
+ spi1: spi@80112000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x80112000 0x1000>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
@@ -934,9 +800,11 @@
<&dma 35 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
- spi@80111000 {
+ spi2: spi@80111000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x80111000 0x1000>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
@@ -949,9 +817,11 @@
<&dma 33 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
- spi@80129000 {
+ spi3: spi@80129000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x80129000 0x1000>;
interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
@@ -964,9 +834,11 @@
<&dma 40 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
power-domains = <&pm_domains DOMAIN_VAPE>;
+
+ status = "disabled";
};
- ux500_serial0: uart@80120000 {
+ serial0: uart@80120000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x80120000 0x1000>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
@@ -981,7 +853,7 @@
status = "disabled";
};
- ux500_serial1: uart@80121000 {
+ serial1: uart@80121000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x80121000 0x1000>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
@@ -996,7 +868,7 @@
status = "disabled";
};
- ux500_serial2: uart@80007000 {
+ serial2: uart@80007000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x80007000 0x1000>;
interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
@@ -1110,9 +982,6 @@
sound {
compatible = "stericsson,snd-soc-mop500";
stericsson,cpu-dai = <&msp1 &msp3>;
- stericsson,audio-codec = <&codec>;
- clocks = <&prcmu_clk PRCMU_SYSCLK>, <&ab8500_clock AB8500_SYSCLK_ULP>, <&ab8500_clock AB8500_SYSCLK_INT>;
- clock-names = "sysclk", "ulpclk", "intclk";
};
msp0: msp@80123000 {
@@ -1190,21 +1059,69 @@
status = "disabled";
};
+ gpu@a0300000 {
+ /*
+ * This block is referred to as "Smart Graphics Adapter SGA500"
+ * in documentation but is in practice a pretty straight-forward
+ * MALI-400 GPU block.
+ */
+ compatible = "stericsson,db8500-mali", "arm,mali-400";
+ reg = <0xa0300000 0x10000>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gp",
+ "gpmmu",
+ "pp0",
+ "ppmmu0",
+ "combined";
+ clocks = <&prcmu_clk PRCMU_ACLK>, <&prcmu_clk PRCMU_SGACLK>;
+ clock-names = "bus", "core";
+ mali-supply = <&db8500_sga_reg>;
+ power-domains = <&pm_domains DOMAIN_VAPE>;
+ };
+
mcde@a0350000 {
- compatible = "stericsson,mcde";
- reg = <0xa0350000 0x1000>, /* MCDE */
- <0xa0351000 0x1000>, /* DSI link 1 */
- <0xa0352000 0x1000>, /* DSI link 2 */
- <0xa0353000 0x1000>; /* DSI link 3 */
+ compatible = "ste,mcde";
+ reg = <0xa0350000 0x1000>;
interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+ epod-supply = <&db8500_b2r2_mcde_reg>;
clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */
<&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */
- <&prcmu_clk PRCMU_PLLDSI>, /* HDMI clock */
- <&prcmu_clk PRCMU_DSI0CLK>, /* DSI 0 */
- <&prcmu_clk PRCMU_DSI1CLK>, /* DSI 1 */
- <&prcmu_clk PRCMU_DSI0ESCCLK>, /* TVout clock 0 */
- <&prcmu_clk PRCMU_DSI1ESCCLK>, /* TVout clock 1 */
- <&prcmu_clk PRCMU_DSI2ESCCLK>; /* TVout clock 2 */
+ <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */
+ clock-names = "mcde", "lcd", "hdmi";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ dsi0: dsi-controller@a0351000 {
+ compatible = "ste,mcde-dsi";
+ reg = <0xa0351000 0x1000>;
+ clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>;
+ clock-names = "hs", "lp";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ dsi1: dsi-controller@a0352000 {
+ compatible = "ste,mcde-dsi";
+ reg = <0xa0352000 0x1000>;
+ clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>;
+ clock-names = "hs", "lp";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ dsi2: dsi-controller@a0353000 {
+ compatible = "ste,mcde-dsi";
+ reg = <0xa0353000 0x1000>;
+ /* This DSI port only has the Low Power / Energy Save clock */
+ clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>;
+ clock-names = "lp";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
cryp@a03cb000 {
--
Gitblit v1.6.2