From 072de836f53be56a70cecf70b43ae43b7ce17376 Mon Sep 17 00:00:00 2001
From: hc <hc@nodka.com>
Date: Mon, 11 Dec 2023 10:08:36 +0000
Subject: [PATCH] mk-rootfs.sh
---
kernel/Documentation/admin-guide/pm/intel_pstate.rst | 161 ++++++++++++++++++++++++++++++++++-------------------
1 files changed, 103 insertions(+), 58 deletions(-)
diff --git a/kernel/Documentation/admin-guide/pm/intel_pstate.rst b/kernel/Documentation/admin-guide/pm/intel_pstate.rst
index 8f1d3de..5072e70 100644
--- a/kernel/Documentation/admin-guide/pm/intel_pstate.rst
+++ b/kernel/Documentation/admin-guide/pm/intel_pstate.rst
@@ -1,10 +1,13 @@
+.. SPDX-License-Identifier: GPL-2.0
+.. include:: <isonum.txt>
+
===============================================
``intel_pstate`` CPU Performance Scaling Driver
===============================================
-::
+:Copyright: |copy| 2017 Intel Corporation
- Copyright (c) 2017 Intel Corp., Rafael J. Wysocki <rafael.j.wysocki@intel.com>
+:Author: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
General Information
@@ -20,11 +23,10 @@
For the processors supported by ``intel_pstate``, the P-state concept is broader
than just an operating frequency or an operating performance point (see the
-`LinuxCon Europe 2015 presentation by Kristen Accardi <LCEU2015_>`_ for more
+LinuxCon Europe 2015 presentation by Kristen Accardi [1]_ for more
information about that). For this reason, the representation of P-states used
by ``intel_pstate`` internally follows the hardware specification (for details
-refer to `Intel® 64 and IA-32 Architectures Software Developer’s Manual
-Volume 3: System Programming Guide <SDM_>`_). However, the ``CPUFreq`` core
+refer to Intel Software Developer’s Manual [2]_). However, the ``CPUFreq`` core
uses frequencies for identifying operating performance points of CPUs and
frequencies are involved in the user space interface exposed by it, so
``intel_pstate`` maps its internal representation of P-states to frequencies too
@@ -52,17 +54,21 @@
Operation Modes
===============
-``intel_pstate`` can operate in three different modes: in the active mode with
-or without hardware-managed P-states support and in the passive mode. Which of
-them will be in effect depends on what kernel command line options are used and
-on the capabilities of the processor.
+``intel_pstate`` can operate in two different modes, active or passive. In the
+active mode, it uses its own internal performance scaling governor algorithm or
+allows the hardware to do preformance scaling by itself, while in the passive
+mode it responds to requests made by a generic ``CPUFreq`` governor implementing
+a certain performance scaling algorithm. Which of them will be in effect
+depends on what kernel command line options are used and on the capabilities of
+the processor.
Active Mode
-----------
-This is the default operation mode of ``intel_pstate``. If it works in this
-mode, the ``scaling_driver`` policy attribute in ``sysfs`` for all ``CPUFreq``
-policies contains the string "intel_pstate".
+This is the default operation mode of ``intel_pstate`` for processors with
+hardware-managed P-states (HWP) support. If it works in this mode, the
+``scaling_driver`` policy attribute in ``sysfs`` for all ``CPUFreq`` policies
+contains the string "intel_pstate".
In this mode the driver bypasses the scaling governors layer of ``CPUFreq`` and
provides its own scaling algorithms for P-state selection. Those algorithms
@@ -117,7 +123,9 @@
internal P-state selection logic is expected to focus entirely on performance.
This will override the EPP/EPB setting coming from the ``sysfs`` interface
-(see `Energy vs Performance Hints`_ below).
+(see `Energy vs Performance Hints`_ below). Moreover, any attempts to change
+the EPP/EPB to a value different from 0 ("performance") via ``sysfs`` in this
+configuration will be rejected.
Also, in this configuration the range of P-states available to the processor's
internal P-state selection logic is always restricted to the upper boundary
@@ -136,12 +144,13 @@
Active Mode Without HWP
~~~~~~~~~~~~~~~~~~~~~~~
-This is the default operation mode for processors that do not support the HWP
-feature. It also is used by default with the ``intel_pstate=no_hwp`` argument
-in the kernel command line. However, in this mode ``intel_pstate`` may refuse
-to work with the given processor if it does not recognize it. [Note that
-``intel_pstate`` will never refuse to work with any processor with the HWP
-feature enabled.]
+This operation mode is optional for processors that do not support the HWP
+feature or when the ``intel_pstate=no_hwp`` argument is passed to the kernel in
+the command line. The active mode is used in those cases if the
+``intel_pstate=active`` argument is passed to the kernel in the command line.
+In this mode ``intel_pstate`` may refuse to work with processors that are not
+recognized by it. [Note that ``intel_pstate`` will never refuse to work with
+any processor with the HWP feature enabled.]
In this mode ``intel_pstate`` registers utilization update callbacks with the
CPU scheduler in order to run a P-state selection algorithm, either
@@ -186,10 +195,15 @@
Passive Mode
------------
-This mode is used if the ``intel_pstate=passive`` argument is passed to the
-kernel in the command line (it implies the ``intel_pstate=no_hwp`` setting too).
-Like in the active mode without HWP support, in this mode ``intel_pstate`` may
-refuse to work with the given processor if it does not recognize it.
+This is the default operation mode of ``intel_pstate`` for processors without
+hardware-managed P-states (HWP) support. It is always used if the
+``intel_pstate=passive`` argument is passed to the kernel in the command line
+regardless of whether or not the given processor supports HWP. [Note that the
+``intel_pstate=no_hwp`` setting causes the driver to start in the passive mode
+if it is not combined with ``intel_pstate=active``.] Like in the active mode
+without HWP support, in this mode ``intel_pstate`` may refuse to work with
+processors that are not recognized by it if HWP is prevented from being enabled
+through the kernel command line.
If the driver works in this mode, the ``scaling_driver`` policy attribute in
``sysfs`` for all ``CPUFreq`` policies contains the string "intel_cpufreq".
@@ -310,10 +324,9 @@
For this reason, there is a list of supported processors in ``intel_pstate`` and
the driver initialization will fail if the detected processor is not in that
-list, unless it supports the `HWP feature <Active Mode_>`_. [The interface to
-obtain all of the information listed above is the same for all of the processors
-supporting the HWP feature, which is why they all are supported by
-``intel_pstate``.]
+list, unless it supports the HWP feature. [The interface to obtain all of the
+information listed above is the same for all of the processors supporting the
+HWP feature, which is why ``intel_pstate`` works with all of them.]
User Space Interface in ``sysfs``
@@ -417,11 +430,16 @@
as well as the per-policy ones) are then reset to their default
values, possibly depending on the target operation mode.]
- That only is supported in some configurations, though (for example, if
- the `HWP feature is enabled in the processor <Active Mode With HWP_>`_,
- the operation mode of the driver cannot be changed), and if it is not
- supported in the current configuration, writes to this attribute will
- fail with an appropriate error.
+``energy_efficiency``
+ This attribute is only present on platforms with CPUs matching the Kaby
+ Lake or Coffee Lake desktop CPU model. By default, energy-efficiency
+ optimizations are disabled on these CPU models if HWP is enabled.
+ Enabling energy-efficiency optimizations may limit maximum operating
+ frequency with or without the HWP feature. With HWP enabled, the
+ optimizations are done only in the turbo frequency range. Without it,
+ they are done in the entire available frequency range. Setting this
+ attribute to "1" enables the energy-efficiency optimizations and setting
+ to "0" disables them.
Interpretation of Policy Attributes
-----------------------------------
@@ -465,6 +483,13 @@
policy for the time interval between the last two invocations of the
driver's utilization update callback by the CPU scheduler for that CPU.
+One more policy attribute is present if the HWP feature is enabled in the
+processor:
+
+``base_frequency``
+ Shows the base frequency of the CPU. Any frequency above this will be
+ in the turbo frequency range.
+
The meaning of these attributes in the `passive mode <Passive Mode_>`_ is the
same as for other scaling drivers.
@@ -488,15 +513,23 @@
2. Each individual CPU is affected by its own per-policy limits (that is, it
cannot be requested to run faster than its own per-policy maximum and it
- cannot be requested to run slower than its own per-policy minimum).
+ cannot be requested to run slower than its own per-policy minimum). The
+ effective performance depends on whether the platform supports per core
+ P-states, hyper-threading is enabled and on current performance requests
+ from other CPUs. When platform doesn't support per core P-states, the
+ effective performance can be more than the policy limits set on a CPU, if
+ other CPUs are requesting higher performance at that moment. Even with per
+ core P-states support, when hyper-threading is enabled, if the sibling CPU
+ is requesting higher performance, the other siblings will get higher
+ performance than their policy limits.
3. The global and per-policy limits can be set independently.
-If the `HWP feature is enabled in the processor <Active Mode With HWP_>`_, the
-resulting effective values are written into its registers whenever the limits
-change in order to request its internal P-state selection logic to always set
-P-states within these limits. Otherwise, the limits are taken into account by
-scaling governors (in the `passive mode <Passive Mode_>`_) and by the driver
+In the `active mode with the HWP feature enabled <Active Mode With HWP_>`_, the
+resulting effective values are written into hardware registers whenever the
+limits change in order to request its internal P-state selection logic to always
+set P-states within these limits. Otherwise, the limits are taken into account
+by scaling governors (in the `passive mode <Passive Mode_>`_) and by the driver
every time before setting a new P-state for a CPU.
Additionally, if the ``intel_pstate=per_cpu_perf_limits`` command line argument
@@ -507,12 +540,11 @@
Energy vs Performance Hints
---------------------------
-If ``intel_pstate`` works in the `active mode with the HWP feature enabled
-<Active Mode With HWP_>`_ in the processor, additional attributes are present
-in every ``CPUFreq`` policy directory in ``sysfs``. They are intended to allow
-user space to help ``intel_pstate`` to adjust the processor's internal P-state
-selection logic by focusing it on performance or on energy-efficiency, or
-somewhere between the two extremes:
+If the hardware-managed P-states (HWP) is enabled in the processor, additional
+attributes, intended to allow user space to help ``intel_pstate`` to adjust the
+processor's internal P-state selection logic by focusing it on performance or on
+energy-efficiency, or somewhere between the two extremes, are present in every
+``CPUFreq`` policy directory in ``sysfs``. They are :
``energy_performance_preference``
Current value of the energy vs performance hint for the given policy
@@ -531,7 +563,11 @@
Strings written to the ``energy_performance_preference`` attribute are
internally translated to integer values written to the processor's
Energy-Performance Preference (EPP) knob (if supported) or its
-Energy-Performance Bias (EPB) knob.
+Energy-Performance Bias (EPB) knob. It is also possible to write a positive
+integer value between 0 to 255, if the EPP feature is present. If the EPP
+feature is not present, writing integer value to this attribute is not
+supported. In this case, user can use the
+"/sys/devices/system/cpu/cpu*/power/energy_perf_bias" interface.
[Note that tasks may by migrated from one CPU to another by the scheduler's
load-balancing algorithm and if different energy vs performance hints are
@@ -546,9 +582,9 @@
On the majority of systems supported by ``intel_pstate``, the ACPI tables
provided by the platform firmware contain ``_PSS`` objects returning information
-that can be used for CPU performance scaling (refer to the `ACPI specification`_
-for details on the ``_PSS`` objects and the format of the information returned
-by them).
+that can be used for CPU performance scaling (refer to the ACPI specification
+[3]_ for details on the ``_PSS`` objects and the format of the information
+returned by them).
The information returned by the ACPI ``_PSS`` objects is used by the
``acpi-cpufreq`` scaling driver. On systems supported by ``intel_pstate``
@@ -612,11 +648,13 @@
Do not register ``intel_pstate`` as the scaling driver even if the
processor is supported by it.
+``active``
+ Register ``intel_pstate`` in the `active mode <Active Mode_>`_ to start
+ with.
+
``passive``
Register ``intel_pstate`` in the `passive mode <Passive Mode_>`_ to
start with.
-
- This option implies the ``no_hwp`` one described below.
``force``
Register ``intel_pstate`` as the scaling driver instead of
@@ -632,13 +670,12 @@
driver is used instead of ``acpi-cpufreq``.
``no_hwp``
- Do not enable the `hardware-managed P-states (HWP) feature
- <Active Mode With HWP_>`_ even if it is supported by the processor.
+ Do not enable the hardware-managed P-states (HWP) feature even if it is
+ supported by the processor.
``hwp_only``
Register ``intel_pstate`` as the scaling driver only if the
- `hardware-managed P-states (HWP) feature <Active Mode With HWP_>`_ is
- supported by the processor.
+ hardware-managed P-states (HWP) feature is supported by the processor.
``support_acpi_ppc``
Take ACPI ``_PPC`` performance limits into account.
@@ -685,7 +722,7 @@
The ``ftrace`` interface can be used for low-level diagnostics of
``intel_pstate``. For example, to check how often the function to set a
-P-state is called, the ``ftrace`` filter can be set to to
+P-state is called, the ``ftrace`` filter can be set to
:c:func:`intel_pstate_set_pstate`::
# cd /sys/kernel/debug/tracing/
@@ -713,6 +750,14 @@
<idle>-0 [000] ..s. 2537.654843: intel_pstate_set_pstate <-intel_pstate_timer_func
-.. _LCEU2015: http://events.linuxfoundation.org/sites/events/files/slides/LinuxConEurope_2015.pdf
-.. _SDM: http://www.intel.com/content/www/us/en/architecture-and-technology/64-ia-32-architectures-software-developer-system-programming-manual-325384.html
-.. _ACPI specification: http://www.uefi.org/sites/default/files/resources/ACPI_6_1.pdf
+References
+==========
+
+.. [1] Kristen Accardi, *Balancing Power and Performance in the Linux Kernel*,
+ https://events.static.linuxfound.org/sites/events/files/slides/LinuxConEurope_2015.pdf
+
+.. [2] *Intel® 64 and IA-32 Architectures Software Developer’s Manual Volume 3: System Programming Guide*,
+ https://www.intel.com/content/www/us/en/architecture-and-technology/64-ia-32-architectures-software-developer-system-programming-manual-325384.html
+
+.. [3] *Advanced Configuration and Power Interface Specification*,
+ https://uefi.org/sites/default/files/resources/ACPI_6_3_final_Jan30.pdf
--
Gitblit v1.6.2