修改4g拨号为QMI,需要在系统里后台执行quectel-CM

hc

2024-10-22 8ac6c7a54ed1b98d142dce24b11c6de6a1e239a5

 kernel/arch/arm64/boot/dts/rockchip/NK-R36S0.dtsi
..
..
@@ -90,9 +90,136 @@
90
90
     	};
91
91
 #endif
92
92
 
93
+#if 0
94
+		leds: leds {
95
+		compatible = "gpio-leds";
96
+		sig_led: sig_led {
97
+			gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;
98
+			default-state = "on";
99
+		};
100
+	};
101
+	
102
+		leds: leds {
103
+		compatible = "gpio-leds";	
104
+		err_led: err_led {
105
+			gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
106
+			default-state = "on";
107
+		};
108
+	};
109
+#endif
110
+
111
+	ndj_io_init {
112
+         	compatible = "nk_io_control";	
113
+			pinctrl-names = "default";
114
+        	pinctrl-0 = <&nk_io_gpio>;
115
+			
116
+			//gpio_op0 = <&gpio1 RK_PD0 GPIO_ACTIVE_HIGH>;
117
+			
118
+			vcc_5v {
119
+				gpio_num = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; //VCC5_IO_EN_GPIO1_A4_3V3
120
+				gpio_function = <0>;	
121
+			};
122
+			
123
+			vcc_12v {
124
+				gpio_num = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;  //VCC12_IO_EN_GPIO0_C7_3V3
125
+				gpio_function = <0>;
126
+			};
127
+			
128
+			vcc_3.3v {
129
+				gpio_num = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>; //VCC3_IO_EN_GPIO0_C4_3V3
130
+				gpio_function = <0>;
131
+			};
132
+			
133
+			ax88772_rst {
134
+				gpio_num = <&gpio3 RK_PB5 GPIO_ACTIVE_HIGH>;  //AX88772_RST_GPIO3_B5_3V3
135
+				gpio_function = <3>;
136
+			};
137
+			
138
+			ax88631_rst {
139
+				gpio_num = <&gpio3 RK_PB6 GPIO_ACTIVE_HIGH>;  //AX88772_RST_GPIO3_B6_3V3
140
+				gpio_function = <3>;
141
+			};
142
+/*
143
+			hub_host3 {
144
+				gpio_num = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>; //HOST3_EN_GPIO4_B2_1V8
145
+				gpio_function = <0>;
146
+			};
147
+*/			
148
+			wake_4g {
149
+				gpio_num = <&gpio1 RK_PB1 GPIO_ACTIVE_LOW>; //4G_WAKEUP_GPIO01_B1_3V3
150
+				gpio_function = <0>;
151
+			};
152
+			
153
+			air_mode_4g {
154
+				gpio_num = <&gpio1 RK_PB0 GPIO_ACTIVE_LOW>; //4G_AIR_MODE_GPIO01_B0_3V3
155
+				gpio_function = <0>;
156
+			};
157
+			
158
+			reset_4g {
159
+				gpio_num = <&gpio1 RK_PB2 GPIO_ACTIVE_LOW>; //4G_RST_GPIO01_B2_3V3
160
+				gpio_function = <3>;
161
+			};
162
+			
163
+			en_4g {
164
+				gpio_num = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>; //4G_PWREN_H_GPIO0_C6
165
+				gpio_function = <0>;
166
+			};
167
+			
168
+			//gpio99 {
169
+			//	gpio_num = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;//HP_EN_GPIO3_A6_3V3
170
+			//	gpio_function = <1>;
171
+			//};
172
+			
173
+			wifi_power_en {
174
+				gpio_num = <&gpio3 RK_PC6 GPIO_ACTIVE_HIGH>; //WIFI_PWREN_GPIO3_C6_1V8
175
+				gpio_function = <0>;
176
+			};
177
+	#if 0		
178
+			do1 {
179
+				gpio_num = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>; 
180
+				gpio_function = <0>;
181
+			};
182
+			
183
+			do2 {
184
+				gpio_num = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
185
+				gpio_function = <0>;
186
+			};
187
+			
188
+			do3 {
189
+				gpio_num = <&gpio1 RK_PD1 GPIO_ACTIVE_HIGH>;
190
+				gpio_function = <0>;
191
+			};
192
+			
193
+			do4 {
194
+				gpio_num = <&gpio1 RK_PD3 GPIO_ACTIVE_HIGH>;
195
+				gpio_function = <0>;
196
+			};
197
+			
198
+			do5 {
199
+				gpio_num = <&gpio2 RK_PD6 GPIO_ACTIVE_LOW>; 
200
+				gpio_function = <0>;
201
+			};
202
+			
203
+			do6 {
204
+				gpio_num = <&gpio2 RK_PD7 GPIO_ACTIVE_LOW>; 
205
+				gpio_function = <0>;
206
+			};
207
+			
208
+			do7 {
209
+				gpio_num = <&gpio3 RK_PA0 GPIO_ACTIVE_LOW>; 
210
+				gpio_function = <0>;
211
+			};
212
+			
213
+			di1 {
214
+				gpio_num = <&gpio2 RK_PD5 GPIO_ACTIVE_HIGH>;
215
+				gpio_function = <1>;
216
+			};
217
+	#endif
218
+		};
219
+#if 0			
93
220
 	    nk_io_init {
94
221
                 compatible = "nk_io_control";
95
-				vcc3_io_en_gpio = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>; //VCC3_IO_EN_GPIO0_C4_3V3
222
+//				vcc3_io_en_gpio = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>; //VCC3_IO_EN_GPIO0_C4_3V3
96
223
                 hub_host2_5V_rest_gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; //HUB_RST_GPIO4_D2_3V3
97
224
                 hub_host3_5v_gpio = <&gpio4 RK_PB2 GPIO_ACTIVE_HIGH>; //HOST3_EN_GPIO4_B2_1V8
98
225
                 vcc_5v_io = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>;   //VCC5_IO_EN_GPIO1_A4_3V3
..
..
@@ -108,7 +235,7 @@
108
235
 				pinctrl-names = "default";
109
236
 				pinctrl-0 = <&nk_io_gpio>;				
110
237
         };
111
-		
238
+#endif	
112
239
 		panel: panel {
113
240
 				compatible = "simple-panel";
114
241
 				backlight = <&backlight>;
..
..
@@ -128,8 +255,8 @@
128
255
 				nodka-lvds = <15>;
129
256
 
130
257
 				display-timings {
131
-                native-mode = <&timing0>;
132
-                timing0: timing0 {
258
+                native-mode = <&timing>;
259
+                timing: timing {
133
260
 					clock-frequency = <72500000>;
134
261
 					hactive = <1280>;
135
262
 					vactive = <800>;
..
..
@@ -146,8 +273,8 @@
146
273
 					};
147
274
 				};
148
275
 				ports {
149
-					panel_in: endpoint {
150
-					remote-endpoint = <&edp_out>;
276
+					panel_in_lvds: endpoint {
277
+					remote-endpoint = <&lvds_out>;
151
278
 						};
152
279
 					};   
153
280
 				};
..
..
@@ -239,7 +366,7 @@
239
366
  */
240
367
  
241
368
 &video_phy1 {
242
-	status = "okay";
369
+	status = "disabled";
243
370
 }; 
244
371
 &dsi1 {
245
372
 	status = "disabled";
..
..
@@ -250,11 +377,11 @@
250
377
 };
251
378
 
252
379
 &dsi1_in_vp1 {
253
-	status = "okay";
380
+	status = "disabled";
254
381
 };
255
382
 
256
383
 &dsi1_panel {
257
-	power-supply = <&vcc3v3_lcd1_n>;   //MIPI_3V3EN_GPIO3_A3_d_3V3
384
+//	power-supply = <&vcc3v3_lcd1_n>;   //MIPI_3V3EN_GPIO3_A3_d_3V3
258
385
     vddio-mipi = <&gpio3 RK_PA4 GPIO_ACTIVE_HIGH>; //MIPI_EN_1V8_GPIO3_A4_d_3V3
259
386
     reset-gpios = <&gpio3 RK_PC7 GPIO_ACTIVE_LOW>; //MIPI_RST_L_GPIO3_C7
260
387
     vcc-5v-gpio = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; //VCC5_IO_EN_GPIO1_A4_3V3
..
..
@@ -274,20 +401,11 @@
274
401
 
275
402
 &edp {
276
403
     force-hpd;
277
-    status = "okay";
278
-    ports {
279
-        port@1 {
280
-            reg = <1>;
281
-            edp_out: endpoint {
282
-                remote-endpoint = <&panel_in>;
283
-            };
284
-        };
285
-    };
404
+	status = "disabled";
286
405
 };
287
406
 
288
407
 &edp_phy {
289
-  status = "okay";
290
-
408
+	status = "disabled";
291
409
 };
292
410
 
293
411
 &edp_in_vp0 {
..
..
@@ -295,18 +413,40 @@
295
413
 };
296
414
 
297
415
 &edp_in_vp1 {
298
-    status = "okay";
416
+    status = "disabled";
299
417
 
300
418
 };
301
419
 
302
420
 &route_edp {
303
-    status = "okay";
421
+    status = "disabled";
304
422
     connect = <&vp1_out_edp>;
305
423
 };
306
424
 
307
425
 &route_edp {
308
-	status = "okay";
426
+	status = "disabled";
309
427
 };
428
+
429
+&lvds {
430
+	status = "disabled";
431
+	ports {
432
+		port@1 {
433
+			reg = <1>;
434
+			lvds_out:endpoint {
435
+				remote-endpoint = <&panel_in_lvds>;
436
+			};
437
+		};
438
+	};
439
+};
440
+
441
+&route_lvds{
442
+	status = "okay";
443
+	connect = <&vp1_out_lvds>;
444
+};
445
+
446
+&lvds_in_vp1 {
447
+	status = "disabled";
448
+};
449
+
310
450
 /*
311
451
 *  edp_end
312
452
 */
..
..
@@ -351,7 +491,7 @@
351
491
 	phy-mode = "rgmii";
352
492
 	clock_in_out = "output";
353
493
 
354
-	snps,reset-gpio = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
494
+	snps,reset-gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>;
355
495
 	snps,reset-active-low;
356
496
 	/* Reset time is 20ms, 100ms for rtl8211f */
357
497
 	snps,reset-delays-us = <0 20000 100000>;
..
..
@@ -371,7 +511,9 @@
371
511
 	rx_delay = <0x2f>;
372
512
 
373
513
 	phy-handle = <&rgmii_phy0>;
514
+	
374
515
 	status = "disabled";
516
+	
375
517
 };
376
518
 
377
519
 &gmac1 {
..
..
@@ -405,9 +547,7 @@
405
547
  * power-supply should switche to vcc3v3_lcd1_n
406
548
  * when mipi panel is connected to dsi1.
407
549
  */
408
-&gt1x {
409
-	power-supply = <&vcc3v3_lcd0_n>;
410
-};
550
+
411
551
 
412
552
 &i2c3 {
413
553
 	status = "okay";
..
..
@@ -426,7 +566,7 @@
426
566
 };
427
567
 
428
568
 &i2c4 {
429
-	status = "okay";
569
+	status = "disabled";
430
570
 	gc8034: gc8034@37 {
431
571
 		compatible = "galaxycore,gc8034";
432
572
 		status = "okay";
..
..
@@ -438,7 +578,6 @@
438
578
 		reset-gpios = <&gpio3 RK_PB6 GPIO_ACTIVE_LOW>;
439
579
 		pwdn-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_LOW>;
440
580
 		rockchip,grf = <&grf>;
441
-		power-domains = <&power RK3568_PD_VI>;
442
581
 		rockchip,camera-module-index = <0>;
443
582
 		rockchip,camera-module-facing = "back";
444
583
 		rockchip,camera-module-name = "RK-CMK-8M-2-v1";
..
..
@@ -472,7 +611,7 @@
472
611
 		};
473
612
 	};
474
613
 	ov5695: ov5695@36 {
475
-		status = "okay";
614
+		status = "disabled";
476
615
 		compatible = "ovti,ov5695";
477
616
 		reg = <0x36>;
478
617
 		clocks = <&cru CLK_CIF_OUT>;
..
..
@@ -525,7 +664,7 @@
525
664
 
526
665
 
527
666
 &pcie30phy {
528
-	status = "okay";
667
+	status = "disabled";
529
668
 };
530
669
 
531
670
 &pcie2x1 {
..
..
@@ -584,12 +723,27 @@
584
723
 							<3 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>,
585
724
 							<3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>,
586
725
 							<3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>,
726
+							<3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>,
727
+							<3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>,
728
+							<3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>,
587
729
 							<3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>,
588
-							<2 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>,//93 SPI2_CS0_M1_3V3
589
-							<2 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>,//94 SPI2_MOSI_M1_3V3
590
-							<2 RK_PD7 RK_FUNC_GPIO &pcfg_pull_none>,//95 SPI2_MISO_M1_3V3
591
-							<3 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>,//96 SPI2_CLK_M1_3V3
592
-							<0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
730
+							<0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_B0_u_3V3  DO1 8
731
+							<0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_B3_u_3V3  DO2 11
732
+							<0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_B4_u_3V3  DO3 12
733
+							<0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_B5_u_3V3  DO4 13
734
+							<0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_B6_u_3V3  DO5 14
735
+							
736
+							<0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_C0_d_3V3  DI1 16
737
+							<0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_C1_d_3V3  DI2 17
738
+							<0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_C2_d_3V3  DI3 18
739
+							<0 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_C3_d_3V3  DI4 19
740
+							<0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>,//GPIO0_C5_d_3V3  DI5 21
741
+							<0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>,
742
+							<4 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>, //sig_led
743
+							<4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>, //err_led
744
+							<4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>, //run_led
745
+							<4 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; //HOST3_EN_GPIO4_B2_1V8
746
+
593
747
 		};
594
748
 	};
595
749
 };
..
..
@@ -615,8 +769,6 @@
615
769
 		};
616
770
 	};
617
771
 };
618
-
619
-
620
772
 
621
773
 
622
774
 
..
..
@@ -656,15 +808,6 @@
656
808
 	pinctrl-0 = <&uart8m0_xfer &uart8m0_ctsn>;
657
809
 };
658
810
 
659
-&vcc3v3_lcd0_n {
660
-	gpio = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>; 
661
-	enable-active-high;
662
-};
663
-
664
-&vcc3v3_lcd1_n {
665
-	gpio = <&gpio3 RK_PA3 GPIO_ACTIVE_HIGH>; //MIPI_3V3EN_GPIO3_A3_d_3V3
666
-	enable-active-high;
667
-};
668
811
 
669
812
 &wireless_wlan {
670
813
 	pinctrl-names = "default";
..
..
@@ -684,17 +827,17 @@
684
827
 	BT,reset_gpio    = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
685
828
     BT,wake_gpio     = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
686
829
     BT,wake_host_irq = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
687
-	status = "okay";
830
+	status = "disabled";
688
831
 };
689
832
 
690
833
 &uart0 {
691
-	status = "okay";
834
+	status = "disabled";
692
835
 };
693
836
 
694
837
 &uart1 {	
695
838
 	pinctrl-names = "default";	
696
839
 	pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;	
697
-	status = "okay";		
840
+	status = "disabled";		
698
841
 };
699
842
 
700
843
 &uart3 {
..
..
@@ -703,7 +846,7 @@
703
846
 };
704
847
 
705
848
 &uart4 {
706
-	status = "okay";
849
+	status = "disabled";
707
850
 	pinctrl-0 = <&uart4m1_xfer>;
708
851
 };
709
852
 
..
..
@@ -712,12 +855,18 @@
712
855
 	pinctrl-0 = <&uart5m1_xfer>;
713
856
 };
714
857
 
858
+
715
859
 &uart7 {
716
860
 	status = "okay";
717
861
 	pinctrl-0 = <&uart7m1_xfer>;
718
862
 };
719
863
 
864
+&uart8 {
865
+	status = "disabled";
866
+	pinctrl-0 = <&uart8m1_xfer>;
867
+};
868
+
720
869
 &uart9 {
721
-	status = "okay";
870
+	status = "disabled";
722
871
 	pinctrl-0 = <&uart9m1_xfer>;
723
872
 };