修改4g拨号为QMI,需要在系统里后台执行quectel-CM

hc

2024-10-22 8ac6c7a54ed1b98d142dce24b11c6de6a1e239a5

 kernel/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts
..
..
@@ -71,8 +71,6 @@
71
71
 
72
72
 	reg_vmmc1: vmmc1 {
73
73
 		compatible = "regulator-fixed";
74
-		pinctrl-names = "default";
75
-		pinctrl-0 = <&mmc1_vcc_en_pin_t004>;
76
74
 		regulator-name = "vmmc1";
77
75
 		regulator-min-microvolt = <3300000>;
78
76
 		regulator-max-microvolt = <3300000>;
..
..
@@ -86,8 +84,6 @@
86
84
 };
87
85
 
88
86
 &i2c0 {
89
-	pinctrl-names = "default";
90
-	pinctrl-0 = <&i2c0_pins_a>;
91
87
 	status = "okay";
92
88
 
93
89
 	axp152: pmic@30 {
..
..
@@ -100,8 +96,6 @@
100
96
 };
101
97
 
102
98
 &mmc0 {
103
-	pinctrl-names = "default";
104
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>;
105
99
 	vmmc-supply = <&reg_vcc3v3>;
106
100
 	bus-width = <4>;
107
101
 	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
..
..
@@ -109,8 +103,6 @@
109
103
 };
110
104
 
111
105
 &mmc1 {
112
-	pinctrl-names = "default";
113
-	pinctrl-0 = <&mmc1_pins_a>;
114
106
 	vmmc-supply = <&reg_vmmc1>;
115
107
 	bus-width = <4>;
116
108
 	non-removable;
..
..
@@ -127,24 +119,7 @@
127
119
 };
128
120
 
129
121
 &pio {
130
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
131
-		pins = "PG12";
132
-		function = "gpio_in";
133
-		bias-pull-up;
134
-	};
135
-
136
-	mmc0_cd_pin_t004: mmc0_cd_pin@0 {
137
-		pins = "PG1";
138
-		function = "gpio_in";
139
-		bias-pull-up;
140
-	};
141
-
142
-	mmc1_vcc_en_pin_t004: mmc1_vcc_en_pin@0 {
143
-		pins = "PB18";
144
-		function = "gpio_out";
145
-	};
146
-
147
-	led_pins_t004: led_pins@0 {
122
+	led_pins_t004: led-pin {
148
123
 		pins = "PB2";
149
124
 		function = "gpio_out";
150
125
 		drive-strength = <20>;
..
..
@@ -158,7 +133,7 @@
158
133
 
159
134
 &uart0 {
160
135
 	pinctrl-names = "default";
161
-	pinctrl-0 = <&uart0_pins_a>;
136
+	pinctrl-0 = <&uart0_pb_pins>;
162
137
 	status = "okay";
163
138
 };
164
139
 
..
..
@@ -168,9 +143,7 @@
168
143
 };
169
144
 
170
145
 &usbphy {
171
-	pinctrl-names = "default";
172
-	pinctrl-0 = <&usb0_id_detect_pin>;
173
-	usb0_id_det-gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
146
+	usb0_id_det-gpios = <&pio 6 12 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG12 */
174
147
 	usb1_vbus-supply = <&reg_usb1_vbus>;
175
148
 	status = "okay";
176
149
 };