forked from ~ljy/RK356X_SDK_RELEASE
blame | history | patch | commit | commitdiff
hc
2024-10-22 8ac6c7a54ed1b98d142dce24b11c6de6a1e239a5 
 kernel/Documentation/devicetree/bindings/net/phy.txt
....@@ -1,73 +1 @@
1
-PHY nodes
2
-
3
-Required properties:
4
-
5
- - interrupts : interrupt specifier for the sole interrupt.
6
- - reg : The ID number for the phy, usually a small integer
7
-
8
-Optional Properties:
9
-
10
-- compatible: Compatible list, may contain
11
-  "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for
12
-  PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45
13
-  specifications. If neither of these are specified, the default is to
14
-  assume clause 22.
15
-
16
-  If the PHY reports an incorrect ID (or none at all) then the
17
-  "compatible" list may contain an entry with the correct PHY ID in the
18
-  form: "ethernet-phy-idAAAA.BBBB" where
19
-     AAAA - The value of the 16 bit Phy Identifier 1 register as
20
-            4 hex digits. This is the chip vendor OUI bits 3:18
21
-     BBBB - The value of the 16 bit Phy Identifier 2 register as
22
-            4 hex digits. This is the chip vendor OUI bits 19:24,
23
-            followed by 10 bits of a vendor specific ID.
24
-
25
-  The compatible list should not contain other values than those
26
-  listed here.
27
-
28
-- max-speed: Maximum PHY supported speed (10, 100, 1000...)
29
-
30
-- broken-turn-around: If set, indicates the PHY device does not correctly
31
-  release the turn around line low at the end of a MDIO transaction.
32
-
33
-- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to
34
-  compensate for the board being designed with the lanes swapped.
35
-
36
-- enet-phy-lane-no-swap: If set, indicates that PHY will disable swap of the
37
-  TX/RX lanes. This property allows the PHY to work correcly after e.g. wrong
38
-  bootstrap configuration caused by issues in PCB layout design.
39
-
40
-- eee-broken-100tx:
41
-- eee-broken-1000t:
42
-- eee-broken-10gt:
43
-- eee-broken-1000kx:
44
-- eee-broken-10gkx4:
45
-- eee-broken-10gkr:
46
-  Mark the corresponding energy efficient ethernet mode as broken and
47
-  request the ethernet to stop advertising it.
48
-
49
-- phy-is-integrated: If set, indicates that the PHY is integrated into the same
50
-  physical package as the Ethernet MAC. If needed, muxers should be configured
51
-  to ensure the integrated PHY is used. The absence of this property indicates
52
-  the muxers should be configured so that the external PHY is used.
53
-
54
-- reset-gpios: The GPIO phandle and specifier for the PHY reset signal.
55
-
56
-- reset-assert-us: Delay after the reset was asserted in microseconds.
57
-  If this property is missing the delay will be skipped.
58
-
59
-- reset-deassert-us: Delay after the reset was deasserted in microseconds.
60
-  If this property is missing the delay will be skipped.
61
-
62
-Example:
63
-
64
-ethernet-phy@0 {
65
-	compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c22";
66
-	interrupt-parent = <&PIC>;
67
-	interrupts = <35 IRQ_TYPE_EDGE_RISING>;
68
-	reg = <0>;
69
-
70
-	reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
71
-	reset-assert-us = <1000>;
72
-	reset-deassert-us = <2000>;
73
-};
1
+This file has moved to ethernet-phy.yaml.