forked from ~ljy/RK356X_SDK_RELEASE
blame | history | patch | commit | commitdiff
hc
2023-12-11 6778948f9de86c3cfaf36725a7c87dcff9ba247f 
 kernel/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
....@@ -12,186 +12,9 @@
1212 
1313 /dts-v1/;
1414 
15
-#include <dt-bindings/gpio/gpio.h>
16
-#include "armada-372x.dtsi"
15
+#include "armada-3720-espressobin.dtsi"
1716 
1817 / {
1918 	model = "Globalscale Marvell ESPRESSOBin Board";
2019 	compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3710";
21
-
22
-	aliases {
23
-		ethernet0 = &eth0;
24
-		/* for dsa slave device */
25
-		ethernet1 = &switch0port1;
26
-		ethernet2 = &switch0port2;
27
-		ethernet3 = &switch0port3;
28
-		serial0 = &uart0;
29
-		serial1 = &uart1;
30
-	};
31
-
32
-	chosen {
33
-		stdout-path = "serial0:115200n8";
34
-	};
35
-
36
-	memory@0 {
37
-		device_type = "memory";
38
-		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
39
-	};
40
-
41
-	vcc_sd_reg1: regulator {
42
-		compatible = "regulator-gpio";
43
-		regulator-name = "vcc_sd1";
44
-		regulator-min-microvolt = <1800000>;
45
-		regulator-max-microvolt = <3300000>;
46
-		regulator-boot-on;
47
-
48
-		gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>;
49
-		gpios-states = <0>;
50
-		states = <1800000 0x1
51
-			  3300000 0x0>;
52
-		enable-active-high;
53
-	};
54
-};
55
-
56
-/* J9 */
57
-&pcie0 {
58
-	pinctrl-names = "default";
59
-	pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
60
-	reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
61
-	status = "okay";
62
-};
63
-
64
-/* J6 */
65
-&sata {
66
-	status = "okay";
67
-};
68
-
69
-/* J1 */
70
-&sdhci1 {
71
-	wp-inverted;
72
-	bus-width = <4>;
73
-	cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>;
74
-	marvell,pad-type = "sd";
75
-	vqmmc-supply = <&vcc_sd_reg1>;
76
-	status = "okay";
77
-};
78
-
79
-&spi0 {
80
-	status = "okay";
81
-
82
-	flash@0 {
83
-		reg = <0>;
84
-		compatible = "winbond,w25q32dw", "jedec,spi-flash";
85
-		spi-max-frequency = <104000000>;
86
-		m25p,fast-read;
87
-
88
-		partitions {
89
-			compatible = "fixed-partitions";
90
-			#address-cells = <1>;
91
-			#size-cells = <1>;
92
-
93
-			partition@0 {
94
-				label = "uboot";
95
-				reg = <0 0x180000>;
96
-			};
97
-
98
-			partition@180000 {
99
-				label = "ubootenv";
100
-				reg = <0x180000 0x10000>;
101
-			};
102
-		};
103
-	};
104
-};
105
-
106
-/* Exported on the micro USB connector J5 through an FTDI */
107
-&uart0 {
108
-	pinctrl-names = "default";
109
-	pinctrl-0 = <&uart1_pins>;
110
-	status = "okay";
111
-};
112
-
113
-/*
114
- * Connector J17 and J18 expose a number of different features. Some pins are
115
- * multiplexed. This is the case for instance for the following features:
116
- * - UART1 (pin 24 = RX, pin 26 = TX). See armada-3720-db.dts for an example of
117
- *   how to enable it. Beware that the signals are 1.8V TTL.
118
- * - I2C
119
- * - SPI
120
- * - MMC
121
- */
122
-
123
-/* J7 */
124
-&usb3 {
125
-	status = "okay";
126
-};
127
-
128
-/* J8 */
129
-&usb2 {
130
-	status = "okay";
131
-};
132
-
133
-&mdio {
134
-	switch0: switch0@1 {
135
-		compatible = "marvell,mv88e6085";
136
-		#address-cells = <1>;
137
-		#size-cells = <0>;
138
-		reg = <1>;
139
-
140
-		dsa,member = <0 0>;
141
-
142
-		ports {
143
-			#address-cells = <1>;
144
-			#size-cells = <0>;
145
-
146
-			switch0port0: port@0 {
147
-				reg = <0>;
148
-				label = "cpu";
149
-				ethernet = <&eth0>;
150
-			};
151
-
152
-			switch0port1: port@1 {
153
-				reg = <1>;
154
-				label = "wan";
155
-				phy-handle = <&switch0phy0>;
156
-			};
157
-
158
-			switch0port2: port@2 {
159
-				reg = <2>;
160
-				label = "lan0";
161
-				phy-handle = <&switch0phy1>;
162
-			};
163
-
164
-			switch0port3: port@3 {
165
-				reg = <3>;
166
-				label = "lan1";
167
-				phy-handle = <&switch0phy2>;
168
-			};
169
-
170
-		};
171
-
172
-		mdio {
173
-			#address-cells = <1>;
174
-			#size-cells = <0>;
175
-
176
-			switch0phy0: switch0phy0@11 {
177
-				reg = <0x11>;
178
-			};
179
-			switch0phy1: switch0phy1@12 {
180
-				reg = <0x12>;
181
-			};
182
-			switch0phy2: switch0phy2@13 {
183
-				reg = <0x13>;
184
-			};
185
-		};
186
-	};
187
-};
188
-
189
-&eth0 {
190
-	phy-mode = "rgmii-id";
191
-	status = "okay";
192
-
193
-	fixed-link {
194
-		speed = <1000>;
195
-		full-duplex;
196
-	};
19720 };