add ax88772C AX88772C_eeprom_tools

hc

2024-05-10 61598093bbdd283a7edc367d900f223070ead8d2

 kernel/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
..
..
@@ -16,8 +16,8 @@
16
16
 	entry in clock-names
17
17
  - clock-names : must contain "sys_ck" for clock of controller,
18
18
 	the following clocks are optional:
19
-	"ref_ck", "mcu_ck" and "dam_ck";
20
- - phys : see usb-hcd.txt in the current directory
19
+	"ref_ck", "mcu_ck" and "dma_ck";
20
+ - phys : see usb-hcd.yaml in the current directory
21
21
  - dr_mode : should be one of "host", "peripheral" or "otg",
22
22
 	refer to usb/generic.txt
23
23
 
..
..
@@ -28,8 +28,13 @@
28
28
 	parent's address space
29
29
  - extcon : external connector for vbus and idpin changes detection, needed
30
30
 	when supports dual-role mode.
31
+	it's considered valid for compatibility reasons, not allowed for
32
+	new bindings, and use "usb-role-switch" property instead.
31
33
  - vbus-supply : reference to the VBUS regulator, needed when supports
32
34
 	dual-role mode.
35
+	it's considered valid for compatibility reasons, not allowed for
36
+	new bindings, and put into a usb-connector node.
37
+	see connector/usb-connector.yaml.
33
38
  - pinctrl-names : a pinctrl state named "default" is optional, and need be
34
39
 	defined if auto drd switch is enabled, that means the property dr_mode
35
40
 	is set as "otg", and meanwhile the property "mediatek,enable-manual-drd"
..
..
@@ -39,6 +44,8 @@
39
44
 
40
45
  - maximum-speed : valid arguments are "super-speed", "high-speed" and
41
46
 	"full-speed"; refer to usb/generic.txt
47
+ - usb-role-switch : use USB Role Switch to support dual-role switch, but
48
+	not extcon; see usb/generic.txt.
42
49
  - enable-manual-drd : supports manual dual-role switch via debugfs; usually
43
50
 	used when receptacle is TYPE-A and also wants to support dual-role
44
51
 	mode.
..
..
@@ -53,7 +60,7 @@
53
60
  - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0,
54
61
 	bit1 for u3port1, ... etc;
55
62
 
56
-additionally the properties from usb-hcd.txt (in the current directory) are
63
+additionally the properties from usb-hcd.yaml (in the current directory) are
57
64
 supported.
58
65
 
59
66
 Sub-nodes:
..
..
@@ -61,6 +68,9 @@
61
68
 if host mode is enabled. The DT binding details of xhci can be found in:
62
69
 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
63
70
 
71
+The port would be added as subnode if use "usb-role-switch" property.
72
+	see graph.txt
73
+
64
74
 Example:
65
75
 ssusb: usb@11271000 {
66
76
 	compatible = "mediatek,mt8173-mtu3";