add audio

hc

2023-12-11 1f93a7dfd1f8d5ff7a5c53246c7534fe2332d6f4

 kernel/arch/arm/boot/dts/qcom-pm8941.dtsi
..
..
@@ -63,43 +63,10 @@
63
63
 			compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
64
64
 			reg = <0xc000>;
65
65
 			gpio-controller;
66
+			gpio-ranges = <&pm8941_gpios 0 0 36>;
66
67
 			#gpio-cells = <2>;
67
-			interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
68
-				     <0 0xc1 0 IRQ_TYPE_NONE>,
69
-				     <0 0xc2 0 IRQ_TYPE_NONE>,
70
-				     <0 0xc3 0 IRQ_TYPE_NONE>,
71
-				     <0 0xc4 0 IRQ_TYPE_NONE>,
72
-				     <0 0xc5 0 IRQ_TYPE_NONE>,
73
-				     <0 0xc6 0 IRQ_TYPE_NONE>,
74
-				     <0 0xc7 0 IRQ_TYPE_NONE>,
75
-				     <0 0xc8 0 IRQ_TYPE_NONE>,
76
-				     <0 0xc9 0 IRQ_TYPE_NONE>,
77
-				     <0 0xca 0 IRQ_TYPE_NONE>,
78
-				     <0 0xcb 0 IRQ_TYPE_NONE>,
79
-				     <0 0xcc 0 IRQ_TYPE_NONE>,
80
-				     <0 0xcd 0 IRQ_TYPE_NONE>,
81
-				     <0 0xce 0 IRQ_TYPE_NONE>,
82
-				     <0 0xcf 0 IRQ_TYPE_NONE>,
83
-				     <0 0xd0 0 IRQ_TYPE_NONE>,
84
-				     <0 0xd1 0 IRQ_TYPE_NONE>,
85
-				     <0 0xd2 0 IRQ_TYPE_NONE>,
86
-				     <0 0xd3 0 IRQ_TYPE_NONE>,
87
-				     <0 0xd4 0 IRQ_TYPE_NONE>,
88
-				     <0 0xd5 0 IRQ_TYPE_NONE>,
89
-				     <0 0xd6 0 IRQ_TYPE_NONE>,
90
-				     <0 0xd7 0 IRQ_TYPE_NONE>,
91
-				     <0 0xd8 0 IRQ_TYPE_NONE>,
92
-				     <0 0xd9 0 IRQ_TYPE_NONE>,
93
-				     <0 0xda 0 IRQ_TYPE_NONE>,
94
-				     <0 0xdb 0 IRQ_TYPE_NONE>,
95
-				     <0 0xdc 0 IRQ_TYPE_NONE>,
96
-				     <0 0xdd 0 IRQ_TYPE_NONE>,
97
-				     <0 0xde 0 IRQ_TYPE_NONE>,
98
-				     <0 0xdf 0 IRQ_TYPE_NONE>,
99
-				     <0 0xe0 0 IRQ_TYPE_NONE>,
100
-				     <0 0xe1 0 IRQ_TYPE_NONE>,
101
-				     <0 0xe2 0 IRQ_TYPE_NONE>,
102
-				     <0 0xe3 0 IRQ_TYPE_NONE>;
68
+			interrupt-controller;
69
+			#interrupt-cells = <2>;
103
70
 
104
71
 			boost_bypass_n_pin: boost-bypass {
105
72
 				pins = "gpio21";
..
..
@@ -211,6 +178,16 @@
211
178
 				qcom,vs-soft-start-strength = <0>;
212
179
 				regulator-initial-mode = <1>;
213
180
 			};
181
+
182
+			pm8941_5vs2: 5vs2 {
183
+				regulator-enable-ramp-delay = <1000>;
184
+				regulator-pull-down;
185
+				regulator-over-current-protection;
186
+				qcom,ocp-max-retries = <10>;
187
+				qcom,ocp-retry-delay = <30>;
188
+				qcom,vs-soft-start-strength = <0>;
189
+				regulator-initial-mode = <1>;
190
+			};
214
191
 		};
215
192
 	};
216
193
 };