forked from ~ljy/RK356X_SDK_RELEASE
blame | history | patch | commit | commitdiff
hc
2024-01-04 1543e317f1da31b75942316931e8f491a8920811 
 kernel/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
....@@ -1,14 +1,8 @@
1
+// SPDX-License-Identifier: GPL-2.0-or-later
12 /*
23  * Copyright 2012 ST-Ericsson AB
34  *
4
- * The code contained herein is licensed under the GNU General Public
5
- * License. You may obtain a copy of the GNU General Public License
6
- * Version 2 or later at the following locations:
7
- *
8
- * http://www.opensource.org/licenses/gpl-license.html
9
- * http://www.gnu.org/copyleft/gpl.html
10
- *
11
- * Device Tree for the TVK1281618 UIB
5
+ * Device Tree for the TVK1281618 family of UIBs
126  */
137 
148 #include <dt-bindings/interrupt-controller/irq.h>
....@@ -87,62 +81,8 @@
8781 				};
8882 			};
8983 		};
90
-		/* Sensors mounted on this board variant */
84
+		/* Sensors mounted on all board variants */
9185 		i2c@80128000 {
92
-			lsm303dlh@18 {
93
-				/* Accelerometer */
94
-				compatible = "st,lsm303dlh-accel";
95
-				st,drdy-int-pin = <1>;
96
-				drive-open-drain;
97
-				reg = <0x18>;
98
-				vdd-supply = <&ab8500_ldo_aux1_reg>;
99
-				vddio-supply = <&db8500_vsmps2_reg>;
100
-				pinctrl-names = "default";
101
-				pinctrl-0 = <&accel_tvk_mode>;
102
-				/*
103
-				 * These interrupts cannot be used: the other component
104
-				 * ST-Micro L3D4200D gyro that is connected to the same lines
105
-				 * cannot set its DRDY line to open drain, so it cannot be
106
-				 * shared with other peripherals. The should be defined for
107
-				 * the falling edge if they could be wired together.
108
-				 *
109
-				 * interrupts-extended =
110
-				 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
111
-				 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
112
-				 */
113
-			};
114
-			lsm303dlh@1e {
115
-				/* Magnetometer */
116
-				compatible = "st,lsm303dlh-magn";
117
-				reg = <0x1e>;
118
-				vdd-supply = <&ab8500_ldo_aux1_reg>;
119
-				vddio-supply = <&db8500_vsmps2_reg>;
120
-				/*
121
-				 * These interrupts cannot be used: the other component
122
-				 * ST-Micro L3D4200D gyro that is connected to the same lines
123
-				 * cannot set its DRDY line to open drain, so it cannot be
124
-				 * shared with other peripherals. The should be defined for
125
-				 * the falling edge if they could be wired together.
126
-				 *
127
-				 * interrupts-extended =
128
-				 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
129
-				 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
130
-				 */
131
-			};
132
-			lis331dl@1c {
133
-				/* Accelerometer */
134
-				compatible = "st,lis331dl-accel";
135
-				st,drdy-int-pin = <1>;
136
-				reg = <0x1c>;
137
-				vdd-supply = <&ab8500_ldo_aux1_reg>;
138
-				vddio-supply = <&db8500_vsmps2_reg>;
139
-				pinctrl-names = "default";
140
-				pinctrl-0 = <&accel_tvk_mode>;
141
-				interrupt-parent = <&gpio2>;
142
-				/* INT2 would need to be open drain */
143
-				interrupts = <18 IRQ_TYPE_EDGE_RISING>,
144
-					     <19 IRQ_TYPE_EDGE_RISING>;
145
-			};
14686 			ak8974@f {
14787 				/* Magnetometer */
14888 				compatible = "asahi-kasei,ak8974";