change wifi driver to cypress

hc

2024-01-05 071106ecf68c401173c58808b1cf5f68cc50d390

 kernel/arch/arm64/boot/dts/rockchip/rk3566-evb1-ddr4-v10.dtsi
old mode 100755new mode 100644
..
..
@@ -67,11 +67,11 @@
67
67
 };
68
68
 
69
69
 &csi2_dphy_hw {
70
-	status = "disabled";
70
+	status = "okay";
71
71
 };
72
72
 
73
73
 &csi2_dphy1 {
74
-	status = "disabled";
74
+	status = "okay";
75
75
 
76
76
 	/*
77
77
 	 * dphy1 only used for split mode,
..
..
@@ -108,7 +108,7 @@
108
108
 };
109
109
 
110
110
 &csi2_dphy2 {
111
-	status = "disabled";
111
+	status = "okay";
112
112
 
113
113
 	/*
114
114
 	 * dphy2 only used for split mode,
..
..
@@ -160,7 +160,7 @@
160
160
  * when dsi0 is enabled
161
161
  */
162
162
 &dsi0 {
163
-	status = "disabled";
163
+	status = "okay";
164
164
 };
165
165
 
166
166
 &dsi0_in_vp0 {
..
..
@@ -168,7 +168,7 @@
168
168
 };
169
169
 
170
170
 &dsi0_in_vp1 {
171
-	status = "disabled";
171
+	status = "okay";
172
172
 };
173
173
 
174
174
 &dsi0_panel {
..
..
@@ -218,37 +218,13 @@
218
218
 	status = "disabled";
219
219
 };
220
220
 
221
-&gmac1 {
222
-	phy-mode = "rgmii";
223
-	clock_in_out = "output";
224
-
225
-	snps,reset-gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
226
-	snps,reset-active-low;
227
-	/* Reset time is 20ms, 100ms for rtl8211f */
228
-	snps,reset-delays-us = <0 20000 100000>;
229
-
230
-	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
231
-	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
232
-	assigned-clock-rates = <0>, <125000000>;
233
-
234
-	pinctrl-names = "default";
235
-	pinctrl-0 = <&gmac1m1_miim
236
-		     &gmac1m1_tx_bus2
237
-		     &gmac1m1_rx_bus2
238
-		     &gmac1m1_rgmii_clk
239
-		     &gmac1m1_rgmii_bus>;
240
-
241
-	tx_delay = <0x4f>;
242
-	rx_delay = <0x26>;
243
-
244
-
245
-	status = "okay";
246
-};
247
-
248
221
 /*
249
222
  * power-supply should switche to vcc3v3_lcd1_n
250
223
  * when mipi panel is connected to dsi1.
251
224
  */
225
+&gt1x {
226
+	power-supply = <&vcc3v3_lcd0_n>;
227
+};
252
228
 
253
229
 &i2c2 {
254
230
 	status = "okay";
..
..
@@ -348,7 +324,7 @@
348
324
 };
349
325
 
350
326
 &video_phy0 {
351
-	status = "disabled";
327
+	status = "okay";
352
328
 };
353
329
 
354
330
 &video_phy1 {
..
..
@@ -398,15 +374,15 @@
398
374
 };
399
375
 
400
376
 &rkisp {
401
-	status = "disabled";
377
+	status = "okay";
402
378
 };
403
379
 
404
380
 &rkisp_mmu {
405
-	status = "disabled";
381
+	status = "okay";
406
382
 };
407
383
 
408
384
 &rkisp_vir0 {
409
-	status = "disabled";
385
+	status = "okay";
410
386
 
411
387
 	port {
412
388
 		#address-cells = <1>;
..
..
@@ -420,13 +396,14 @@
420
396
 };
421
397
 
422
398
 &route_dsi0 {
423
-	status = "disabled";
399
+	status = "okay";
424
400
 	connect = <&vp1_out_dsi0>;
425
401
 };
426
402
 
427
403
 &sdmmc2 {
428
404
 	max-frequency = <150000000>;
429
-	supports-sdio;
405
+	no-sd;
406
+	no-mmc;
430
407
 	bus-width = <4>;
431
408
 	disable-wp;
432
409
 	cap-sd-highspeed;
..
..
@@ -473,6 +450,10 @@
473
450
 	WIFI,host_wake_irq = <&gpio3 RK_PD4 GPIO_ACTIVE_HIGH>;
474
451
 };
475
452
 
453
+&work_led {
454
+	gpios = <&gpio2 RK_PB2 GPIO_ACTIVE_HIGH>;
455
+};
456
+
476
457
 &pinctrl {
477
458
 	cam {
478
459
 		camera_pwr: camera-pwr {