#include <linux/kernel.h>
|
#include <linux/of_pci.h>
|
#include <linux/of_irq.h>
|
#include <linux/export.h>
|
|
/**
|
* of_irq_parse_pci - Resolve the interrupt for a PCI device
|
* @pdev: the device whose interrupt is to be resolved
|
* @out_irq: structure of_irq filled by this function
|
*
|
* This function resolves the PCI interrupt for a given PCI device. If a
|
* device-node exists for a given pci_dev, it will use normal OF tree
|
* walking. If not, it will implement standard swizzling and walk up the
|
* PCI tree until an device-node is found, at which point it will finish
|
* resolving using the OF tree walking.
|
*/
|
int of_irq_parse_pci(const struct pci_dev *pdev, struct of_phandle_args *out_irq)
|
{
|
struct device_node *dn, *ppnode;
|
struct pci_dev *ppdev;
|
__be32 laddr[3];
|
u8 pin;
|
int rc;
|
|
/* Check if we have a device node, if yes, fallback to standard
|
* device tree parsing
|
*/
|
dn = pci_device_to_OF_node(pdev);
|
if (dn) {
|
rc = of_irq_parse_one(dn, 0, out_irq);
|
if (!rc)
|
return rc;
|
}
|
|
/* Ok, we don't, time to have fun. Let's start by building up an
|
* interrupt spec. we assume #interrupt-cells is 1, which is standard
|
* for PCI. If you do different, then don't use that routine.
|
*/
|
rc = pci_read_config_byte(pdev, PCI_INTERRUPT_PIN, &pin);
|
if (rc != 0)
|
goto err;
|
/* No pin, exit with no error message. */
|
if (pin == 0)
|
return -ENODEV;
|
|
/* Now we walk up the PCI tree */
|
for (;;) {
|
/* Get the pci_dev of our parent */
|
ppdev = pdev->bus->self;
|
|
/* Ouch, it's a host bridge... */
|
if (ppdev == NULL) {
|
ppnode = pci_bus_to_OF_node(pdev->bus);
|
|
/* No node for host bridge ? give up */
|
if (ppnode == NULL) {
|
rc = -EINVAL;
|
goto err;
|
}
|
} else {
|
/* We found a P2P bridge, check if it has a node */
|
ppnode = pci_device_to_OF_node(ppdev);
|
}
|
|
/* Ok, we have found a parent with a device-node, hand over to
|
* the OF parsing code.
|
* We build a unit address from the linux device to be used for
|
* resolution. Note that we use the linux bus number which may
|
* not match your firmware bus numbering.
|
* Fortunately, in most cases, interrupt-map-mask doesn't
|
* include the bus number as part of the matching.
|
* You should still be careful about that though if you intend
|
* to rely on this function (you ship a firmware that doesn't
|
* create device nodes for all PCI devices).
|
*/
|
if (ppnode)
|
break;
|
|
/* We can only get here if we hit a P2P bridge with no node,
|
* let's do standard swizzling and try again
|
*/
|
pin = pci_swizzle_interrupt_pin(pdev, pin);
|
pdev = ppdev;
|
}
|
|
out_irq->np = ppnode;
|
out_irq->args_count = 1;
|
out_irq->args[0] = pin;
|
laddr[0] = cpu_to_be32((pdev->bus->number << 16) | (pdev->devfn << 8));
|
laddr[1] = laddr[2] = cpu_to_be32(0);
|
rc = of_irq_parse_raw(laddr, out_irq);
|
if (rc)
|
goto err;
|
return 0;
|
err:
|
dev_err(&pdev->dev, "of_irq_parse_pci() failed with rc=%d\n", rc);
|
return rc;
|
}
|
EXPORT_SYMBOL_GPL(of_irq_parse_pci);
|
|
/**
|
* of_irq_parse_and_map_pci() - Decode a PCI irq from the device tree and map to a virq
|
* @dev: The pci device needing an irq
|
* @slot: PCI slot number; passed when used as map_irq callback. Unused
|
* @pin: PCI irq pin number; passed when used as map_irq callback. Unused
|
*
|
* @slot and @pin are unused, but included in the function so that this
|
* function can be used directly as the map_irq callback to pci_fixup_irqs().
|
*/
|
int of_irq_parse_and_map_pci(const struct pci_dev *dev, u8 slot, u8 pin)
|
{
|
struct of_phandle_args oirq;
|
int ret;
|
|
ret = of_irq_parse_pci(dev, &oirq);
|
if (ret)
|
return 0; /* Proper return code 0 == NO_IRQ */
|
|
return irq_create_of_mapping(&oirq);
|
}
|
EXPORT_SYMBOL_GPL(of_irq_parse_and_map_pci);
|
