/*
|
* SPDX-License-Identifier: BSD-2-Clause
|
*
|
* Copyright (c) 2019 Western Digital Corporation or its affiliates.
|
*
|
* Authors:
|
* Anup Patel <anup.patel@wdc.com>
|
*/
|
|
#include <sbi/riscv_io.h>
|
#include <sbi_utils/serial/uart8250.h>
|
|
/* clang-format off */
|
|
#define UART_RBR_OFFSET 0 /* In: Recieve Buffer Register */
|
#define UART_THR_OFFSET 0 /* Out: Transmitter Holding Register */
|
#define UART_DLL_OFFSET 0 /* Out: Divisor Latch Low */
|
#define UART_IER_OFFSET 1 /* I/O: Interrupt Enable Register */
|
#define UART_DLM_OFFSET 1 /* Out: Divisor Latch High */
|
#define UART_FCR_OFFSET 2 /* Out: FIFO Control Register */
|
#define UART_IIR_OFFSET 2 /* I/O: Interrupt Identification Register */
|
#define UART_LCR_OFFSET 3 /* Out: Line Control Register */
|
#define UART_MCR_OFFSET 4 /* Out: Modem Control Register */
|
#define UART_LSR_OFFSET 5 /* In: Line Status Register */
|
#define UART_MSR_OFFSET 6 /* In: Modem Status Register */
|
#define UART_SCR_OFFSET 7 /* I/O: Scratch Register */
|
#define UART_MDR1_OFFSET 8 /* I/O: Mode Register */
|
|
#define UART_LSR_FIFOE 0x80 /* Fifo error */
|
#define UART_LSR_TEMT 0x40 /* Transmitter empty */
|
#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
|
#define UART_LSR_BI 0x10 /* Break interrupt indicator */
|
#define UART_LSR_FE 0x08 /* Frame error indicator */
|
#define UART_LSR_PE 0x04 /* Parity error indicator */
|
#define UART_LSR_OE 0x02 /* Overrun error indicator */
|
#define UART_LSR_DR 0x01 /* Receiver data ready */
|
#define UART_LSR_BRK_ERROR_BITS 0x1E /* BI, FE, PE, OE bits */
|
|
/* clang-format on */
|
|
static volatile void *uart8250_base;
|
static u32 uart8250_in_freq;
|
static u32 uart8250_baudrate;
|
static u32 uart8250_reg_width;
|
static u32 uart8250_reg_shift;
|
|
static u32 get_reg(u32 num)
|
{
|
u32 offset = num << uart8250_reg_shift;
|
|
if (uart8250_reg_width == 1)
|
return readb(uart8250_base + offset);
|
else if (uart8250_reg_width == 2)
|
return readw(uart8250_base + offset);
|
else
|
return readl(uart8250_base + offset);
|
}
|
|
static void set_reg(u32 num, u32 val)
|
{
|
u32 offset = num << uart8250_reg_shift;
|
|
if (uart8250_reg_width == 1)
|
writeb(val, uart8250_base + offset);
|
else if (uart8250_reg_width == 2)
|
writew(val, uart8250_base + offset);
|
else
|
writel(val, uart8250_base + offset);
|
}
|
|
void uart8250_putc(char ch)
|
{
|
while ((get_reg(UART_LSR_OFFSET) & UART_LSR_THRE) == 0)
|
;
|
|
set_reg(UART_THR_OFFSET, ch);
|
}
|
|
int uart8250_getc(void)
|
{
|
if (get_reg(UART_LSR_OFFSET) & UART_LSR_DR)
|
return get_reg(UART_RBR_OFFSET);
|
return -1;
|
}
|
|
int uart8250_init(unsigned long base, u32 in_freq, u32 baudrate, u32 reg_shift,
|
u32 reg_width)
|
{
|
u16 bdiv;
|
|
uart8250_base = (volatile void *)base;
|
uart8250_reg_shift = reg_shift;
|
uart8250_reg_width = reg_width;
|
uart8250_in_freq = in_freq;
|
uart8250_baudrate = baudrate;
|
|
bdiv = uart8250_in_freq / (16 * uart8250_baudrate);
|
|
/* Disable all interrupts */
|
set_reg(UART_IER_OFFSET, 0x00);
|
/* Enable DLAB */
|
set_reg(UART_LCR_OFFSET, 0x80);
|
|
if (bdiv) {
|
/* Set divisor low byte */
|
set_reg(UART_DLL_OFFSET, bdiv & 0xff);
|
/* Set divisor high byte */
|
set_reg(UART_DLM_OFFSET, (bdiv >> 8) & 0xff);
|
}
|
|
/* 8 bits, no parity, one stop bit */
|
set_reg(UART_LCR_OFFSET, 0x03);
|
/* Enable FIFO */
|
set_reg(UART_FCR_OFFSET, 0x01);
|
/* No modem control DTR RTS */
|
set_reg(UART_MCR_OFFSET, 0x00);
|
/* Clear line status */
|
get_reg(UART_LSR_OFFSET);
|
/* Read receive buffer */
|
get_reg(UART_RBR_OFFSET);
|
/* Set scratchpad */
|
set_reg(UART_SCR_OFFSET, 0x00);
|
|
return 0;
|
}
|
