menu "Library routines"
|
|
config BCH
|
bool "Enable Software based BCH ECC"
|
help
|
Enables software based BCH ECC algorithm present in lib/bch.c
|
This is used by SoC platforms which do not have built-in ELM
|
hardware engine required for BCH ECC correction.
|
|
config CC_OPTIMIZE_LIBS_FOR_SPEED
|
bool "Optimize libraries for speed"
|
help
|
Enabling this option will pass "-O2" to gcc when compiling
|
under "lib" directory.
|
|
If unsure, say N.
|
|
config HAVE_PRIVATE_LIBGCC
|
bool
|
|
config USE_PRIVATE_LIBGCC
|
bool "Use private libgcc"
|
depends on HAVE_PRIVATE_LIBGCC
|
default y if HAVE_PRIVATE_LIBGCC && ((ARM && !ARM64) || MIPS)
|
help
|
This option allows you to use the built-in libgcc implementation
|
of U-Boot instead of the one provided by the compiler.
|
If unsure, say N.
|
|
config SYS_HZ
|
int
|
default 1000
|
help
|
The frequency of the timer returned by get_timer().
|
get_timer() must operate in milliseconds and this option must be
|
set to 1000.
|
|
config SYS_STACK_SIZE
|
hex
|
default 0x200000
|
help
|
The system stack size.
|
|
config USE_TINY_PRINTF
|
bool "Enable tiny printf() version"
|
help
|
This option enables a tiny, stripped down printf version.
|
This should only be used in space limited environments,
|
like SPL versions with hard memory limits. This version
|
reduces the code size by about 2.5KiB on armv7.
|
|
The supported format specifiers are %c, %s, %u/%d and %x.
|
|
config PANIC_HANG
|
bool "Do not reset the system on fatal error"
|
help
|
Define this option to stop the system in case of a fatal error,
|
so that you have to reset it manually. This is probably NOT a good
|
idea for an embedded system where you want the system to reboot
|
automatically as fast as possible, but it may be useful during
|
development since you can try to debug the conditions that lead to
|
the situation.
|
|
config REGEX
|
bool "Enable regular expression support"
|
default y if NET
|
help
|
If this variable is defined, U-Boot is linked against the
|
SLRE (Super Light Regular Expression) library, which adds
|
regex support to some commands, for example "env grep" and
|
"setexpr".
|
|
config LIB_RAND
|
bool "Pseudo-random library support "
|
help
|
This library provides pseudo-random number generator functions.
|
|
config SPL_TINY_MEMSET
|
bool "Use a very small memset() in SPL"
|
depends on SPL
|
help
|
The faster memset() is the arch-specific one (if available) enabled
|
by CONFIG_USE_ARCH_MEMSET. If that is not enabled, we can still get
|
better performance by writing a word at a time. But in very
|
size-constrained envrionments even this may be too big. Enable this
|
option to reduce code size slightly at the cost of some speed.
|
|
config TPL_TINY_MEMSET
|
bool "Use a very small memset() in TPL"
|
help
|
The faster memset() is the arch-specific one (if available) enabled
|
by CONFIG_USE_ARCH_MEMSET. If that is not enabled, we can still get
|
better performance by writing a word at a time. But in very
|
size-constrained envrionments even this may be too big. Enable this
|
option to reduce code size slightly at the cost of some speed.
|
|
config RBTREE
|
bool
|
|
config BITREVERSE
|
bool
|
|
config SYSMEM
|
bool "System memory management"
|
default y
|
help
|
This enables support for system permanent memory management.
|
|
config BIDRAM
|
bool "GD board bi_dram[] memory management"
|
default y
|
help
|
This enables support for GD board bi_dram[] memory management.
|
|
source lib/dhry/Kconfig
|
|
menu "Security support"
|
|
config AES
|
bool "Support the AES algorithm"
|
help
|
This provides a means to encrypt and decrypt data using the AES
|
(Advanced Encryption Standard). This algorithm uses a symetric key
|
and is widely used as a streaming cipher. Different key lengths are
|
supported by the algorithm but only a 128-bit key is supported at
|
present.
|
|
source lib/rsa/Kconfig
|
|
config TPM
|
bool "Trusted Platform Module (TPM) Support"
|
depends on DM
|
help
|
This enables support for TPMs which can be used to provide security
|
features for your board. The TPM can be connected via LPC or I2C
|
and a sandbox TPM is provided for testing purposes. Use the 'tpm'
|
command to interactive the TPM. Driver model support is provided
|
for the low-level TPM interface, but only one TPM is supported at
|
a time by the TPM library.
|
|
endmenu
|
|
menu "Boot Configuration"
|
|
config XBC
|
bool "Boot Configuration support"
|
depends on ANDROID_BOOT_IMAGE
|
default n
|
help
|
This enables support of Boot Configuration which can be used
|
to pass boot configuration parameters to user space. These
|
parameters will show up in /proc/bootconfig similar to the kernel
|
parameters that show up in /proc/cmdline
|
|
endmenu
|
|
menu "Hashing Support"
|
|
config SHA1
|
bool "Enable SHA1 support"
|
help
|
This option enables support of hashing using SHA1 algorithm.
|
The hash is calculated in software.
|
The SHA1 algorithm produces a 160-bit (20-byte) hash value
|
(digest).
|
|
config SHA256
|
bool "Enable SHA256 support"
|
help
|
This option enables support of hashing using SHA256 algorithm.
|
The hash is calculated in software.
|
The SHA256 algorithm produces a 256-bit (32-byte) hash value
|
(digest).
|
|
config SHA512
|
bool "Enable SHA512 support"
|
help
|
This option enables support of hashing using SHA512 algorithm.
|
The hash is calculated in software.
|
The SHA512 algorithm produces a 512-bit (64-byte) hash value
|
(digest).
|
|
config SHA_HW_ACCEL
|
bool "Enable hashing using hardware"
|
help
|
This option enables hardware acceleration
|
for SHA1/SHA256 hashing.
|
This affects the 'hash' command and also the
|
hash_lookup_algo() function.
|
|
config SHA_PROG_HW_ACCEL
|
bool "Enable Progressive hashing support using hardware"
|
depends on SHA_HW_ACCEL
|
help
|
This option enables hardware-acceleration for
|
SHA1/SHA256 progressive hashing.
|
Data can be streamed in a block at a time and the hashing
|
is performed in hardware.
|
|
config MD5
|
bool
|
|
config CRC32C
|
bool
|
|
endmenu
|
|
menu "Compression Support"
|
|
config LZ4
|
bool "Enable LZ4 decompression support"
|
help
|
If this option is set, support for LZ4 compressed images
|
is included. The LZ4 algorithm can run in-place as long as the
|
compressed image is loaded to the end of the output buffer, and
|
trades lower compression ratios for much faster decompression.
|
|
NOTE: This implements the release version of the LZ4 frame
|
format as generated by default by the 'lz4' command line tool.
|
This is not the same as the outdated, less efficient legacy
|
frame format currently (2015) implemented in the Linux kernel
|
(generated by 'lz4 -l'). The two formats are incompatible.
|
|
config LZMA
|
bool "Enable LZMA decompression support"
|
help
|
This enables support for LZMA (Lempel-Ziv-Markov chain algorithm),
|
a dictionary compression algorithm that provides a high compression
|
ratio and fairly fast decompression speed. See also
|
CONFIG_CMD_LZMADEC which provides a decode command.
|
|
config SPL_LZMA
|
bool "Enable LZMA decompression support in SPL"
|
depends on SPL
|
help
|
This enables support for LZMA (Lempel-Ziv-Markov chain algorithm),
|
a dictionary compression algorithm that provides a high compression
|
ratio and fairly fast decompression speed. See also
|
|
config LZO
|
bool "Enable LZO decompression support"
|
help
|
This enables support for LZO compression algorithm.r
|
|
config SPL_LZO
|
bool "Enable LZO decompression support in SPL"
|
help
|
This enables support for LZO compression algorithm in the SPL.
|
|
config SPL_GZIP
|
bool "Enable gzip decompression support for SPL build"
|
select SPL_ZLIB
|
help
|
This enables support for GZIP compression altorithm for SPL boot.
|
|
config SPL_ZLIB
|
bool
|
help
|
This enables compression lib for SPL boot.
|
|
endmenu
|
|
config ERRNO_STR
|
bool "Enable function for getting errno-related string message"
|
help
|
The function errno_str(int errno), returns a pointer to the errno
|
corresponding text message:
|
- if errno is null or positive number - a pointer to "Success" message
|
- if errno is negative - a pointer to errno related message
|
|
config HEXDUMP
|
bool "Enable hexdump"
|
help
|
This enables functions for printing dumps of binary data.
|
|
config OF_LIBFDT
|
bool "Enable the FDT library"
|
default y if OF_CONTROL
|
help
|
This enables the FDT library (libfdt). It provides functions for
|
accessing binary device tree images in memory, such as adding and
|
removing nodes and properties, scanning through the tree and finding
|
particular compatible nodes. The library operates on a flattened
|
version of the device tree.
|
|
config OF_LIBFDT_OVERLAY
|
bool "Enable the FDT library overlay support"
|
help
|
This enables the FDT library (libfdt) overlay support.
|
|
config SPL_OF_LIBFDT
|
bool "Enable the FDT library for SPL"
|
default y if SPL_OF_CONTROL
|
help
|
This enables the FDT library (libfdt). It provides functions for
|
accessing binary device tree images in memory, such as adding and
|
removing nodes and properties, scanning through the tree and finding
|
particular compatible nodes. The library operates on a flattened
|
version of the device tree.
|
|
config TPL_OF_LIBFDT
|
bool "Enable the FDT library for TPL"
|
default y if TPL_OF_CONTROL
|
help
|
This enables the FDT library (libfdt). It provides functions for
|
accessing binary device tree images in memory, such as adding and
|
removing nodes and properties, scanning through the tree and finding
|
particular compatible nodes. The library operates on a flattened
|
version of the device tree.
|
|
config FDT_FIXUP_PARTITIONS
|
bool "overwrite MTD partitions in DTS through defined in 'mtdparts'"
|
depends on OF_LIBFDT
|
default n
|
help
|
Allow overwriting defined partitions in the device tree blob
|
using partition info defined in the 'mtdparts' environment
|
variable.
|
|
menu "System tables"
|
depends on (!EFI && !SYS_COREBOOT) || (ARM && EFI_LOADER)
|
|
config GENERATE_SMBIOS_TABLE
|
bool "Generate an SMBIOS (System Management BIOS) table"
|
default y
|
depends on X86 || EFI_LOADER
|
help
|
The System Management BIOS (SMBIOS) specification addresses how
|
motherboard and system vendors present management information about
|
their products in a standard format by extending the BIOS interface
|
on Intel architecture systems.
|
|
Check http://www.dmtf.org/standards/smbios for details.
|
|
config SMBIOS_MANUFACTURER
|
string "SMBIOS Manufacturer"
|
depends on GENERATE_SMBIOS_TABLE
|
default SYS_VENDOR
|
help
|
The board manufacturer to store in SMBIOS structures.
|
Change this to override the default one (CONFIG_SYS_VENDOR).
|
|
config SMBIOS_PRODUCT_NAME
|
string "SMBIOS Product Name"
|
depends on GENERATE_SMBIOS_TABLE
|
default SYS_BOARD
|
help
|
The product name to store in SMBIOS structures.
|
Change this to override the default one (CONFIG_SYS_BOARD).
|
|
config LIB_RATIONAL
|
bool "enable continued fraction calculation routines"
|
|
config SPL_LIB_RATIONAL
|
bool "enable continued fraction calculation routines for SPL"
|
depends on SPL
|
|
endmenu
|
|
source lib/efi/Kconfig
|
source lib/efi_loader/Kconfig
|
source lib/avb/libavb/Kconfig
|
source lib/avb/libavb_ab/Kconfig
|
source lib/avb/libavb_atx/Kconfig
|
source lib/avb/libavb_user/Kconfig
|
source lib/avb/rk_avb_user/Kconfig
|
source lib/optee_clientApi/Kconfig
|
endmenu
|
