hc
2025-02-14 bbb9540dc49f70f6b703d1c8d1b85fa5f602d86e
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
/* SPDX-License-Identifier: GPL-2.0 */
/*
 * include/asm/sunbpp.h
 */
 
#ifndef _ASM_SPARC_SUNBPP_H
#define _ASM_SPARC_SUNBPP_H
 
struct bpp_regs {
  /* DMA registers */
  __volatile__ __u32 p_csr;        /* DMA Control/Status Register */
  __volatile__ __u32 p_addr;        /* Address Register */
  __volatile__ __u32 p_bcnt;        /* Byte Count Register */
  __volatile__ __u32 p_tst_csr;        /* Test Control/Status (DMA2 only) */
  /* Parallel Port registers */
  __volatile__ __u16 p_hcr;        /* Hardware Configuration Register */
  __volatile__ __u16 p_ocr;        /* Operation Configuration Register */
  __volatile__ __u8 p_dr;        /* Parallel Data Register */
  __volatile__ __u8 p_tcr;        /* Transfer Control Register */
  __volatile__ __u8 p_or;        /* Output Register */
  __volatile__ __u8 p_ir;        /* Input Register */
  __volatile__ __u16 p_icr;        /* Interrupt Control Register */
};
 
/* P_HCR. Time is in increments of SBus clock. */
#define P_HCR_TEST      0x8000      /* Allows buried counters to be read */
#define P_HCR_DSW       0x7f00      /* Data strobe width (in ticks) */
#define P_HCR_DDS       0x007f      /* Data setup before strobe (in ticks) */
 
/* P_OCR. */
#define P_OCR_MEM_CLR   0x8000
#define P_OCR_DATA_SRC  0x4000      /* )                  */
#define P_OCR_DS_DSEL   0x2000      /* )  Bidirectional      */
#define P_OCR_BUSY_DSEL 0x1000      /* )    selects            */
#define P_OCR_ACK_DSEL  0x0800      /* )                  */
#define P_OCR_EN_DIAG   0x0400
#define P_OCR_BUSY_OP   0x0200      /* Busy operation */
#define P_OCR_ACK_OP    0x0100      /* Ack operation */
#define P_OCR_SRST      0x0080      /* Reset state machines. Not selfcleaning. */
#define P_OCR_IDLE      0x0008      /* PP data transfer state machine is idle */
#define P_OCR_V_ILCK    0x0002      /* Versatec faded. Zebra only. */
#define P_OCR_EN_VER    0x0001      /* Enable Versatec (0 - enable). Zebra only. */
 
/* P_TCR */
#define P_TCR_DIR       0x08
#define P_TCR_BUSY      0x04
#define P_TCR_ACK       0x02
#define P_TCR_DS        0x01        /* Strobe */
 
/* P_OR */
#define P_OR_V3         0x20        /* )                 */
#define P_OR_V2         0x10        /* ) on Zebra only   */
#define P_OR_V1         0x08        /* )                 */
#define P_OR_INIT       0x04
#define P_OR_AFXN       0x02        /* Auto Feed */
#define P_OR_SLCT_IN    0x01
 
/* P_IR */
#define P_IR_PE         0x04
#define P_IR_SLCT       0x02
#define P_IR_ERR        0x01
 
/* P_ICR */
#define P_DS_IRQ        0x8000      /* RW1  */
#define P_ACK_IRQ       0x4000      /* RW1  */
#define P_BUSY_IRQ      0x2000      /* RW1  */
#define P_PE_IRQ        0x1000      /* RW1  */
#define P_SLCT_IRQ      0x0800      /* RW1  */
#define P_ERR_IRQ       0x0400      /* RW1  */
#define P_DS_IRQ_EN     0x0200      /* RW   Always on rising edge */
#define P_ACK_IRQ_EN    0x0100      /* RW   Always on rising edge */
#define P_BUSY_IRP      0x0080      /* RW   1= rising edge */
#define P_BUSY_IRQ_EN   0x0040      /* RW   */
#define P_PE_IRP        0x0020      /* RW   1= rising edge */
#define P_PE_IRQ_EN     0x0010      /* RW   */
#define P_SLCT_IRP      0x0008      /* RW   1= rising edge */
#define P_SLCT_IRQ_EN   0x0004      /* RW   */
#define P_ERR_IRP       0x0002      /* RW1  1= rising edge */
#define P_ERR_IRQ_EN    0x0001      /* RW   */
 
#endif /* !(_ASM_SPARC_SUNBPP_H) */