// SPDX-License-Identifier: GPL-2.0-or-later
|
/*
|
* Copyright 2012 Freescale Semiconductor, Inc.
|
*
|
* Author: Fabio Estevam <fabio.estevam@freescale.com>
|
*/
|
|
/dts-v1/;
|
#include <dt-bindings/gpio/gpio.h>
|
#include "imx23.dtsi"
|
|
/ {
|
model = "i.MX23 Olinuxino Low Cost Board";
|
compatible = "olimex,imx23-olinuxino", "fsl,imx23";
|
|
memory@40000000 {
|
device_type = "memory";
|
reg = <0x40000000 0x04000000>;
|
};
|
|
apb@80000000 {
|
apbh@80000000 {
|
ssp0: spi@80010000 {
|
compatible = "fsl,imx23-mmc";
|
pinctrl-names = "default";
|
pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
|
bus-width = <4>;
|
broken-cd;
|
status = "okay";
|
};
|
|
pinctrl@80018000 {
|
pinctrl-names = "default";
|
pinctrl-0 = <&hog_pins_a>;
|
|
hog_pins_a: hog@0 {
|
reg = <0>;
|
fsl,pinmux-ids = <
|
MX23_PAD_GPMI_ALE__GPIO_0_17
|
>;
|
fsl,drive-strength = <MXS_DRIVE_4mA>;
|
fsl,voltage = <MXS_VOLTAGE_HIGH>;
|
fsl,pull-up = <MXS_PULL_DISABLE>;
|
};
|
|
led_pin_gpio2_1: led_gpio2_1@0 {
|
reg = <0>;
|
fsl,pinmux-ids = <
|
MX23_PAD_SSP1_DETECT__GPIO_2_1
|
>;
|
fsl,drive-strength = <MXS_DRIVE_4mA>;
|
fsl,voltage = <MXS_VOLTAGE_HIGH>;
|
fsl,pull-up = <MXS_PULL_DISABLE>;
|
};
|
};
|
|
ssp1: spi@80034000 {
|
#address-cells = <1>;
|
#size-cells = <0>;
|
compatible = "fsl,imx23-spi";
|
pinctrl-names = "default";
|
pinctrl-0 = <&spi2_pins_a>;
|
status = "okay";
|
};
|
};
|
|
apbx@80040000 {
|
lradc@80050000 {
|
status = "okay";
|
};
|
|
i2c: i2c@80058000 {
|
pinctrl-names = "default";
|
pinctrl-0 = <&i2c_pins_b>;
|
status = "okay";
|
};
|
|
duart: serial@80070000 {
|
pinctrl-names = "default";
|
pinctrl-0 = <&duart_pins_a>;
|
status = "okay";
|
};
|
|
auart0: serial@8006c000 {
|
pinctrl-names = "default";
|
pinctrl-0 = <&auart0_2pins_a>;
|
status = "okay";
|
};
|
|
usbphy0: usbphy@8007c000 {
|
status = "okay";
|
};
|
};
|
};
|
|
ahb@80080000 {
|
usb0: usb@80080000 {
|
dr_mode = "host";
|
vbus-supply = <®_usb0_vbus>;
|
status = "okay";
|
};
|
};
|
|
regulators {
|
compatible = "simple-bus";
|
#address-cells = <1>;
|
#size-cells = <0>;
|
|
reg_usb0_vbus: regulator@0 {
|
compatible = "regulator-fixed";
|
reg = <0>;
|
regulator-name = "usb0_vbus";
|
regulator-min-microvolt = <5000000>;
|
regulator-max-microvolt = <5000000>;
|
enable-active-high;
|
startup-delay-us = <300>; /* LAN9215 requires a POR of 200us minimum */
|
gpio = <&gpio0 17 0>;
|
};
|
};
|
|
leds {
|
compatible = "gpio-leds";
|
pinctrl-names = "default";
|
pinctrl-0 = <&led_pin_gpio2_1>;
|
|
user {
|
label = "green";
|
gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
|
};
|
};
|
};
|
