1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
| // SPDX-License-Identifier: GPL-2.0+
| /*
| * Copyright (C) 2016 Stefan Wahren <stefan.wahren@i2se.com>
| */
|
| /dts-v1/;
| #include "bcm2835.dtsi"
| #include "bcm2835-rpi.dtsi"
| #include "bcm283x-rpi-usb-otg.dtsi"
|
| / {
| compatible = "raspberrypi,model-zero", "brcm,bcm2835";
| model = "Raspberry Pi Zero";
|
| memory@0 {
| device_type = "memory";
| reg = <0 0x20000000>;
| };
|
| leds {
| led-act {
| gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
| };
| };
| };
|
| &gpio {
| /*
| * This is based on the official GPU firmware DT blob.
| *
| * Legend:
| * "NC" = not connected (no rail from the SoC)
| * "FOO" = GPIO line named "FOO" on the schematic
| * "FOO_N" = GPIO line named "FOO" on schematic, active low
| */
| gpio-line-names = "ID_SDA",
| "ID_SCL",
| "SDA1",
| "SCL1",
| "GPIO_GCLK",
| "GPIO5",
| "GPIO6",
| "SPI_CE1_N",
| "SPI_CE0_N",
| "SPI_MISO",
| "SPI_MOSI",
| "SPI_SCLK",
| "GPIO12",
| "GPIO13",
| /* Serial port */
| "TXD0",
| "RXD0",
| "GPIO16",
| "GPIO17",
| "GPIO18",
| "GPIO19",
| "GPIO20",
| "GPIO21",
| "GPIO22",
| "GPIO23",
| "GPIO24",
| "GPIO25",
| "GPIO26",
| "GPIO27",
| "SDA0",
| "SCL0",
| "NC", /* GPIO30 */
| "NC", /* GPIO31 */
| "CAM_GPIO1", /* GPIO32 */
| "NC", /* GPIO33 */
| "NC", /* GPIO34 */
| "NC", /* GPIO35 */
| "NC", /* GPIO36 */
| "NC", /* GPIO37 */
| "NC", /* GPIO38 */
| "NC", /* GPIO39 */
| "NC", /* GPIO40 */
| "CAM_GPIO0", /* GPIO41 */
| "NC", /* GPIO42 */
| "NC", /* GPIO43 */
| "NC", /* GPIO44 */
| "NC", /* GPIO45 */
| "HDMI_HPD_N",
| "STATUS_LED_N",
| /* Used by SD Card */
| "SD_CLK_R",
| "SD_CMD_R",
| "SD_DATA0_R",
| "SD_DATA1_R",
| "SD_DATA2_R",
| "SD_DATA3_R";
|
| pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
|
| /* I2S interface */
| i2s_alt0: i2s_alt0 {
| brcm,pins = <18 19 20 21>;
| brcm,function = <BCM2835_FSEL_ALT0>;
| };
| };
|
| &hdmi {
| hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
| power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
| status = "okay";
| };
|
| &sdhost {
| pinctrl-names = "default";
| pinctrl-0 = <&sdhost_gpio48>;
| bus-width = <4>;
| status = "okay";
| };
|
| &uart0 {
| pinctrl-names = "default";
| pinctrl-0 = <&uart0_gpio14>;
| status = "okay";
| };
|
|
