/*
|
* Configuration for Xilinx ZynqMP
|
* (C) Copyright 2014 - 2015 Xilinx, Inc.
|
* Michal Simek <michal.simek@xilinx.com>
|
*
|
* Based on Configuration for Versatile Express
|
*
|
* SPDX-License-Identifier: GPL-2.0+
|
*/
|
|
#ifndef __XILINX_ZYNQMP_H
|
#define __XILINX_ZYNQMP_H
|
|
#define CONFIG_REMAKE_ELF
|
|
/* #define CONFIG_ARMV8_SWITCH_TO_EL1 */
|
|
/* Generic Interrupt Controller Definitions */
|
#define CONFIG_GICV2
|
#define GICD_BASE 0xF9010000
|
#define GICC_BASE 0xF9020000
|
|
#define CONFIG_SYS_ALT_MEMTEST
|
#define CONFIG_SYS_MEMTEST_SCRATCH 0xfffc0000
|
|
#ifndef CONFIG_NR_DRAM_BANKS
|
# define CONFIG_NR_DRAM_BANKS 2
|
#endif
|
#define CONFIG_SYS_MEMTEST_START 0
|
#define CONFIG_SYS_MEMTEST_END 1000
|
|
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
|
|
/* Generic Timer Definitions - setup in EL3. Setup by ATF for other cases */
|
#if !defined(COUNTER_FREQUENCY)
|
# define COUNTER_FREQUENCY 100000000
|
#endif
|
|
/* Size of malloc() pool */
|
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 0x2000000)
|
|
/* Serial setup */
|
#define CONFIG_ARM_DCC
|
#define CONFIG_CPU_ARMV8
|
#define CONFIG_ZYNQ_SERIAL
|
|
#define CONFIG_CONS_INDEX 0
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
{ 4800, 9600, 19200, 38400, 57600, 115200 }
|
|
/* Command line configuration */
|
#define CONFIG_MP
|
|
/* BOOTP options */
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
#define CONFIG_BOOTP_BOOTPATH
|
#define CONFIG_BOOTP_GATEWAY
|
#define CONFIG_BOOTP_HOSTNAME
|
#define CONFIG_BOOTP_MAY_FAIL
|
#define CONFIG_BOOTP_DNS
|
#define CONFIG_BOOTP_PXE
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
/* Diff from config_distro_defaults.h */
|
#define CONFIG_SUPPORT_RAW_INITRD
|
#if !defined(CONFIG_SPL_BUILD)
|
#define CONFIG_ENV_VARS_UBOOT_CONFIG
|
#endif
|
#define CONFIG_AUTO_COMPLETE
|
|
#if defined(CONFIG_MMC_SDHCI_ZYNQ)
|
# define CONFIG_SUPPORT_EMMC_BOOT
|
# ifndef CONFIG_ZYNQ_SDHCI_MAX_FREQ
|
# define CONFIG_ZYNQ_SDHCI_MAX_FREQ 200000000
|
# endif
|
#endif
|
|
#ifdef CONFIG_NAND_ARASAN
|
# define CONFIG_SYS_MAX_NAND_DEVICE 1
|
# define CONFIG_SYS_NAND_ONFI_DETECTION
|
#endif
|
|
/* Miscellaneous configurable options */
|
#define CONFIG_SYS_LOAD_ADDR 0x8000000
|
|
#if defined(CONFIG_ZYNQMP_USB)
|
#define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x1800000
|
#define DFU_DEFAULT_POLL_TIMEOUT 300
|
#define CONFIG_USB_CABLE_CHECK
|
#define CONFIG_USB_FUNCTION_THOR
|
#define CONFIG_THOR_RESET_OFF
|
#define DFU_ALT_INFO_RAM \
|
"dfu_ram_info=" \
|
"setenv dfu_alt_info " \
|
"Image ram $kernel_addr $kernel_size\\\\;" \
|
"system.dtb ram $fdt_addr $fdt_size\0" \
|
"dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
|
"thor_ram=run dfu_ram_info && thordown 0 ram 0\0"
|
|
#define DFU_ALT_INFO \
|
DFU_ALT_INFO_RAM
|
|
#ifndef CONFIG_SPL_BUILD
|
# define PARTS_DEFAULT \
|
"partitions=uuid_disk=${uuid_gpt_disk};" \
|
"name=""boot"",size=16M,uuid=${uuid_gpt_boot};" \
|
"name=""Linux"",size=-M,uuid=${uuid_gpt_Linux}\0"
|
#endif
|
#endif
|
|
#if !defined(DFU_ALT_INFO)
|
# define DFU_ALT_INFO
|
#endif
|
|
#if !defined(PARTS_DEFAULT)
|
# define PARTS_DEFAULT
|
#endif
|
|
/* Do not preserve environment */
|
#define CONFIG_ENV_SIZE 0x8000
|
|
/* Monitor Command Prompt */
|
/* Console I/O Buffer Size */
|
#define CONFIG_SYS_CBSIZE 2048
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
|
#define CONFIG_SYS_LONGHELP
|
#define CONFIG_CMDLINE_EDITING
|
#define CONFIG_SYS_MAXARGS 64
|
|
/* Ethernet driver */
|
#if defined(CONFIG_ZYNQ_GEM)
|
# define CONFIG_NET_MULTI
|
# define CONFIG_MII
|
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
|
# define CONFIG_PHY_MARVELL
|
# define CONFIG_PHY_NATSEMI
|
# define CONFIG_PHY_TI
|
# define CONFIG_PHY_VITESSE
|
# define CONFIG_PHY_REALTEK
|
# define PHY_ANEG_TIMEOUT 20000
|
#endif
|
|
/* I2C */
|
#if defined(CONFIG_SYS_I2C_ZYNQ)
|
# define CONFIG_SYS_I2C
|
# define CONFIG_SYS_I2C_ZYNQ_SPEED 100000
|
# define CONFIG_SYS_I2C_ZYNQ_SLAVE 0
|
#endif
|
|
/* EEPROM */
|
#ifdef CONFIG_ZYNQMP_EEPROM
|
# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
|
# define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
|
# define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
|
# define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
|
# define CONFIG_SYS_EEPROM_SIZE (64 * 1024)
|
#endif
|
|
#ifdef CONFIG_SATA_CEVA
|
#define CONFIG_LIBATA
|
#define CONFIG_SCSI_AHCI
|
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
|
#define CONFIG_SYS_SCSI_MAX_LUN 1
|
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
|
CONFIG_SYS_SCSI_MAX_LUN)
|
#endif
|
|
#define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024)
|
|
#define CONFIG_BOARD_EARLY_INIT_R
|
#define CONFIG_CLOCKS
|
|
#define ENV_MEM_LAYOUT_SETTINGS \
|
"fdt_high=10000000\0" \
|
"initrd_high=10000000\0" \
|
"fdt_addr_r=0x40000000\0" \
|
"pxefile_addr_r=0x10000000\0" \
|
"kernel_addr_r=0x18000000\0" \
|
"scriptaddr=0x02000000\0" \
|
"ramdisk_addr_r=0x02100000\0" \
|
|
#if defined(CONFIG_MMC_SDHCI_ZYNQ)
|
# define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0) func(MMC, mmc, 1)
|
#else
|
# define BOOT_TARGET_DEVICES_MMC(func)
|
#endif
|
|
#if defined(CONFIG_SATA_CEVA)
|
# define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
|
#else
|
# define BOOT_TARGET_DEVICES_SCSI(func)
|
#endif
|
|
#if defined(CONFIG_ZYNQMP_USB)
|
# define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0) func(USB, usb, 1)
|
#else
|
# define BOOT_TARGET_DEVICES_USB(func)
|
#endif
|
|
#define BOOT_TARGET_DEVICES(func) \
|
BOOT_TARGET_DEVICES_MMC(func) \
|
BOOT_TARGET_DEVICES_USB(func) \
|
BOOT_TARGET_DEVICES_SCSI(func) \
|
func(PXE, pxe, na) \
|
func(DHCP, dhcp, na)
|
|
#include <config_distro_bootcmd.h>
|
|
/* Initial environment variables */
|
#ifndef CONFIG_EXTRA_ENV_SETTINGS
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
ENV_MEM_LAYOUT_SETTINGS \
|
BOOTENV \
|
DFU_ALT_INFO
|
#endif
|
|
/* SPL can't handle all huge variables - define just DFU */
|
#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_DFU)
|
#undef CONFIG_EXTRA_ENV_SETTINGS
|
# define CONFIG_EXTRA_ENV_SETTINGS \
|
"dfu_alt_info_ram=uboot.bin ram 0x8000000 0x1000000;" \
|
"atf-uboot.ub ram 0x10000000 0x1000000;" \
|
"Image ram 0x80000 0x3f80000;" \
|
"system.dtb ram 0x4000000 0x100000\0" \
|
"dfu_bufsiz=0x1000\0"
|
#endif
|
|
#define CONFIG_SPL_TEXT_BASE 0xfffc0000
|
#define CONFIG_SPL_STACK 0xfffffffc
|
#define CONFIG_SPL_MAX_SIZE 0x40000
|
|
/* Just random location in OCM */
|
#define CONFIG_SPL_BSS_START_ADDR 0x0
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
|
|
#define CONFIG_SPL_FRAMEWORK
|
|
/* u-boot is like dtb */
|
#define CONFIG_SPL_FS_LOAD_ARGS_NAME "u-boot.bin"
|
#define CONFIG_SYS_SPL_ARGS_ADDR 0x8000000
|
|
/* ATF is my kernel image */
|
#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "atf-uboot.ub"
|
|
/* FIT load address for RAM boot */
|
#define CONFIG_SPL_LOAD_FIT_ADDRESS 0x10000000
|
|
/* MMC support */
|
#ifdef CONFIG_MMC_SDHCI_ZYNQ
|
# define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
|
# define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0 /* unused */
|
# define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0 /* unused */
|
# define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0 /* unused */
|
# define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
|
#endif
|
|
#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_DFU)
|
# undef CONFIG_CMD_BOOTD
|
# define CONFIG_SPL_ENV_SUPPORT
|
# define CONFIG_SPL_HASH_SUPPORT
|
# define CONFIG_ENV_MAX_ENTRIES 10
|
|
# define CONFIG_SYS_SPL_MALLOC_START 0x20000000
|
# define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
|
|
#ifdef CONFIG_SPL_SYS_MALLOC_SIMPLE
|
# error "Disable CONFIG_SPL_SYS_MALLOC_SIMPLE. Full malloc needs to be used"
|
#endif
|
#endif
|
|
#define CONFIG_BOARD_EARLY_INIT_F
|
|
#endif /* __XILINX_ZYNQMP_H */
|
