/*
|
* Copyright (C) 2016-2017
|
* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
|
*
|
* SPDX-License-Identifier: GPL-2.0+
|
*/
|
|
#ifndef __CONFIG_H
|
#define __CONFIG_H
|
|
#include <config_distro_defaults.h>
|
#include "mx6_common.h"
|
|
#define CONFIG_SPL_LIBCOMMON_SUPPORT
|
#include "imx6_spl.h"
|
|
#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
|
#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + 0x80000)
|
#define CONFIG_SPL_OS_BOOT
|
#define CONFIG_SYS_OS_BASE (CONFIG_SYS_FLASH_BASE + 0x180000)
|
#define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + 0x1980000)
|
#define CONFIG_SYS_FDT_SIZE (48 * SZ_1K)
|
#define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000
|
|
/*
|
* Below defines are set but NOT really used since we by
|
* design force U-Boot run when we boot in development
|
* mode from SD card (SD2)
|
*/
|
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR (0x800)
|
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (0x80)
|
#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR (0x1000)
|
#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
|
#define CONFIG_SPL_FS_LOAD_ARGS_NAME "imx6q-mccmon.dtb"
|
|
/* Size of malloc() pool */
|
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
|
|
#define CONFIG_BOARD_EARLY_INIT_F
|
#define CONFIG_BOARD_LATE_INIT
|
|
#define CONFIG_MXC_UART
|
#define CONFIG_MXC_UART_BASE UART1_BASE
|
|
#define CONFIG_SYS_MEMTEST_START 0x10000000
|
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
|
|
#define CONFIG_MXC_SPI
|
#define CONFIG_SF_DEFAULT_BUS 2
|
#define CONFIG_SF_DEFAULT_CS 0
|
#define CONFIG_SF_DEFAULT_SPEED 25000000
|
#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
|
|
/* I2C Configs */
|
#define CONFIG_SYS_I2C
|
#define CONFIG_SYS_I2C_MXC
|
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
|
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
/* MMC Configuration */
|
#define CONFIG_SYS_FSL_USDHC_NUM 2
|
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
|
|
/* NOR 16-bit mode */
|
#define CONFIG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR
|
#define CONFIG_SYS_FLASH_PROTECTION
|
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
|
#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
#define CONFIG_FLASH_CFI_DRIVER /* Use drivers/cfi_flash.c */
|
#define CONFIG_FLASH_VERIFY
|
|
/* NOR Flash MTD */
|
#define CONFIG_FLASH_CFI_DRIVER
|
#define CONFIG_FLASH_CFI_MTD
|
#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
|
#define CONFIG_SYS_FLASH_BANKS_LIST { (CONFIG_SYS_FLASH_BASE) }
|
#define CONFIG_SYS_FLASH_BANKS_SIZES { (32 * SZ_1M) }
|
|
/* MTD support */
|
|
#define MTDIDS_DEFAULT "nor0=8000000.nor"
|
#define MTDPARTS_DEFAULT \
|
"mtdparts=8000000.nor:" \
|
"32m@0x0(mccmon6-image.nor)," \
|
"256k@0x40000(u-boot-env.nor)," \
|
"1m@0x80000(u-boot.nor)," \
|
"8m@0x180000(kernel.nor)," \
|
"8m@0x980000(swupdate-kernel.nor)," \
|
"8m@0x1180000(swupdate-rootfs.nor)," \
|
"128k@0x1980000(kernel-dtb.nor)," \
|
"128k@0x19C0000(swupdate-kernel-dtb.nor)"
|
|
/* USB Configs */
|
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
|
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
|
#define CONFIG_MXC_USB_FLAGS 0
|
|
/* Ethernet Configuration */
|
#define CONFIG_FEC_MXC
|
#define CONFIG_MII
|
#define IMX_FEC_BASE ENET_BASE_ADDR
|
#define CONFIG_FEC_XCV_TYPE RGMII
|
#define CONFIG_ETHPRIME "FEC"
|
#define CONFIG_FEC_MXC_PHYADDR 1
|
|
#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
"console=ttymxc0,115200 quiet\0" \
|
"fdtfile=imx6q-mccmon6.dtb\0" \
|
"fdt_high=0xffffffff\0" \
|
"initrd_high=0xffffffff\0" \
|
"boot_os=yes\0" \
|
"download_kernel=" \
|
"tftpboot ${kernel_addr} ${kernel_file};" \
|
"tftpboot ${fdt_addr} ${fdtfile};\0" \
|
"get_boot_medium=" \
|
"setenv boot_medium nor;" \
|
"setexpr.l _src_sbmr1 *0x020d8004;" \
|
"setexpr _b_medium ${_src_sbmr1} '&' 0x00000040;" \
|
"if test ${_b_medium} = 40; then " \
|
"setenv boot_medium sdcard;" \
|
"fi\0" \
|
"kernel_file=uImage\0" \
|
"load_kernel=" \
|
"load mmc ${bootdev}:${bootpart} ${kernel_addr} uImage;" \
|
"load mmc ${bootdev}:${bootpart} ${fdt_addr} ${fdtfile};\0" \
|
"boot_sd=" \
|
"echo '#######################';" \
|
"echo '# Factory SDcard Boot #';" \
|
"echo '#######################';" \
|
"setenv mmcdev 1;" \
|
"setenv mmcfactorydev 0;" \
|
"setenv mmcfactorypart 1;" \
|
"run factory_flash_img;\0" \
|
"boot_nor=" \
|
"setenv kernelnor 0x08180000;" \
|
"setenv dtbnor 0x09980000;" \
|
"setenv bootargs console=${console} " \
|
""MTDPARTS_DEFAULT" " \
|
"root=/dev/mmcblk1 rootfstype=ext4 rw rootwait noinitrd;" \
|
"cp.l ${dtbnor} ${dtbloadaddr} 0x8000;" \
|
"bootm ${kernelnor} - ${dtbloadaddr};\0" \
|
"boot_recovery=" \
|
"echo '#######################';" \
|
"echo '# RECOVERY SWU Boot #';" \
|
"echo '#######################';" \
|
"setenv rootfsloadaddr 0x13000000;" \
|
"setenv swukernelnor 0x08980000;" \
|
"setenv swurootfsnor 0x09180000;" \
|
"setenv swudtbnor 0x099A0000;" \
|
"setenv bootargs console=${console} " \
|
""MTDPARTS_DEFAULT" " \
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
":${hostname}::off root=/dev/ram rw;" \
|
"cp.l ${swurootfsnor} ${rootfsloadaddr} 0x200000;" \
|
"cp.l ${swudtbnor} ${dtbloadaddr} 0x8000;" \
|
"bootm ${swukernelnor} ${rootfsloadaddr} ${dtbloadaddr};\0" \
|
"boot_tftp=" \
|
"echo '#######################';" \
|
"echo '# TFTP Boot #';" \
|
"echo '#######################';" \
|
"if run download_kernel; then " \
|
"setenv bootargs console=${console} " \
|
"root=/dev/mmcblk0p2 rootwait;" \
|
"bootm ${kernel_addr} - ${fdt_addr};" \
|
"fi\0" \
|
"bootcmd=" \
|
"if test -n ${recovery_status}; then " \
|
"run boot_recovery;" \
|
"else " \
|
"if test ! -n ${boot_medium}; then " \
|
"run get_boot_medium;" \
|
"if test ${boot_medium} = sdcard; then " \
|
"run boot_sd;" \
|
"else " \
|
"run boot_nor;" \
|
"fi;" \
|
"else " \
|
"if test ${boot_medium} = tftp; then " \
|
"run boot_tftp;" \
|
"fi;" \
|
"fi;" \
|
"fi\0" \
|
"mtdparts=" MTDPARTS_DEFAULT "\0" \
|
"fdt_addr=0x18000000\0" \
|
"bootdev=1\0" \
|
"bootpart=1\0" \
|
"kernel_addr=" __stringify(CONFIG_LOADADDR) "\0" \
|
"netdev=eth0\0" \
|
"load_addr=0x11000000\0" \
|
"dtbloadaddr=0x12000000\0" \
|
"uboot_file=u-boot.img\0" \
|
"SPL_file=SPL\0" \
|
"load_uboot=tftp ${load_addr} ${uboot_file}\0" \
|
"nor_img_addr=0x11000000\0" \
|
"nor_img_file=core-image-lwn-mccmon6.nor\0" \
|
"emmc_img_file=core-image-lwn-mccmon6.ext4\0" \
|
"nor_bank_start=" __stringify(CONFIG_SYS_FLASH_BASE) "\0" \
|
"nor_img_size=0x02000000\0" \
|
"factory_script_file=factory.scr\0" \
|
"factory_load_script=" \
|
"if test -e mmc ${mmcdev}:${mmcfactorypart} " \
|
"${factory_script_file}; then " \
|
"load mmc ${mmcdev}:${mmcfactorypart} " \
|
"${loadaddr} ${factory_script_file};" \
|
"fi\0" \
|
"factory_script=echo Running factory script from mmc${mmcdev} ...; " \
|
"source ${loadaddr}\0" \
|
"factory_flash_img="\
|
"echo 'Flash mccmon6 with factory images'; " \
|
"if run factory_load_script; then " \
|
"run factory_script;" \
|
"else " \
|
"echo No factory script: ${factory_script_file} found on " \
|
"device ${mmcdev};" \
|
"run factory_nor_img;" \
|
"run factory_eMMC_img;" \
|
"fi\0" \
|
"factory_eMMC_img="\
|
"echo 'Update mccmon6 eMMC image'; " \
|
"if load mmc ${mmcdev}:${mmcfactorypart} " \
|
"${loadaddr} ${emmc_img_file}; then " \
|
"setexpr fw_sz ${filesize} / 0x200;" \
|
"setexpr fw_sz ${fw_sz} + 1;" \
|
"mmc dev ${mmcfactorydev};" \
|
"mmc write ${loadaddr} 0x0 ${fw_sz};" \
|
"fi\0" \
|
"factory_nor_img="\
|
"echo 'Update mccmon6 NOR image'; " \
|
"if load mmc ${mmcdev}:${mmcfactorypart} " \
|
"${nor_img_addr} ${nor_img_file}; then " \
|
"run nor_update;" \
|
"fi\0" \
|
"nor_update=" \
|
"protect off ${nor_bank_start} +${nor_img_size};" \
|
"erase ${nor_bank_start} +${nor_img_size};" \
|
"setexpr nor_img_size ${nor_img_size} / 4; " \
|
"cp.l ${nor_img_addr} ${nor_bank_start} ${nor_img_size}\0" \
|
"tftp_nor_uboot="\
|
"echo 'Update mccmon6 NOR U-BOOT via TFTP'; " \
|
"setenv nor_img_file u-boot.img; " \
|
"setenv nor_img_size 0x80000; " \
|
"setenv nor_bank_start 0x08080000; " \
|
"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
|
"run nor_update;" \
|
"fi\0" \
|
"tftp_nor_uImg="\
|
"echo 'Update mccmon6 NOR uImage via TFTP'; " \
|
"setenv nor_img_file uImage; " \
|
"setenv nor_img_size 0x500000; " \
|
"setenv nor_bank_start 0x08180000; " \
|
"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
|
"run nor_update;" \
|
"fi\0" \
|
"tftp_nor_dtb="\
|
"echo 'Update mccmon6 NOR DTB via TFTP'; " \
|
"setenv nor_img_file imx6q-mccmon6.dtb; " \
|
"setenv nor_img_size 0x20000; " \
|
"setenv nor_bank_start 0x09980000; " \
|
"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
|
"run nor_update;" \
|
"fi\0" \
|
"tftp_nor_img="\
|
"echo 'Update mccmon6 NOR image via TFTP'; " \
|
"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
|
"run nor_update;" \
|
"fi\0" \
|
"tftp_nor_SPL="\
|
"if tftp ${load_addr} SPL_padded; then " \
|
"erase 0x08000000 +0x20000;" \
|
"cp.b ${load_addr} 0x08000000 0x20000;" \
|
"fi;\0" \
|
"tftp_sd_SPL="\
|
"if mmc dev 1; then " \
|
"if tftp ${load_addr} ${SPL_file}; then " \
|
"setexpr fw_sz ${filesize} / 0x200; " \
|
"setexpr fw_sz ${fw_sz} + 1; " \
|
"mmc write ${load_addr} 0x2 ${fw_sz};" \
|
"fi;" \
|
"fi;\0" \
|
"tftp_sd_uboot="\
|
"if mmc dev 1; then " \
|
"if run load_uboot; then " \
|
"setexpr fw_sz ${filesize} / 0x200; " \
|
"setexpr fw_sz ${fw_sz} + 1; " \
|
"mmc write ${load_addr} 0x8A ${fw_sz};" \
|
"fi;" \
|
"fi;\0"
|
|
/* Physical Memory Map */
|
#define CONFIG_NR_DRAM_BANKS 1
|
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
|
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
|
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
|
|
#define CONFIG_SYS_INIT_SP_OFFSET \
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
|
|
/* Environment organization */
|
#define CONFIG_ENV_SIZE (SZ_128K)
|
|
/* Envs are stored in NOR flash */
|
#define CONFIG_ENV_SECT_SIZE (SZ_128K)
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000)
|
|
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + 0x60000)
|
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
|
|
#endif /* __CONFIG_H * */
|
