/*
|
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
|
*
|
* SPDX-License-Identifier: GPL-2.0+
|
*/
|
|
#ifndef _CONFIG_DB_88F6820_AMC_H
|
#define _CONFIG_DB_88F6820_AMC_H
|
|
/*
|
* High Level Configuration Options (easy to change)
|
*/
|
|
#define CONFIG_DISPLAY_BOARDINFO_LATE
|
|
/*
|
* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
|
* for DDR ECC byte filling in the SPL before loading the main
|
* U-Boot into it.
|
*/
|
#define CONFIG_SYS_TEXT_BASE 0x00800000
|
#define CONFIG_SYS_TCLK 200000000 /* 200MHz */
|
|
/*
|
* Commands configuration
|
*/
|
|
/* SPI NOR flash default params, used by sf commands */
|
#define CONFIG_SF_DEFAULT_BUS 1
|
#define CONFIG_SF_DEFAULT_SPEED 1000000
|
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
|
|
/* Partition support */
|
|
/* Additional FS support/configuration */
|
#define CONFIG_SUPPORT_VFAT
|
|
/* USB/EHCI configuration */
|
#define CONFIG_EHCI_IS_TDI
|
|
/* Environment in SPI NOR flash */
|
#define CONFIG_ENV_SPI_BUS 1
|
#define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */
|
#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */
|
#define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */
|
|
#define CONFIG_PHY_MARVELL /* there is a marvell phy */
|
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
|
|
/* PCIe support */
|
#ifndef CONFIG_SPL_BUILD
|
#define CONFIG_PCI_MVEBU
|
#define CONFIG_PCI_SCAN_SHOW
|
#endif
|
|
/* NAND */
|
#define CONFIG_SYS_NAND_USE_FLASH_BBT
|
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
|
#define CONFIG_SYS_ALT_MEMTEST
|
|
/* Keep device tree and initrd in lower memory so the kernel can access them */
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
"fdt_high=0x10000000\0" \
|
"initrd_high=0x10000000\0"
|
|
/* SPL */
|
/*
|
* Select the boot device here
|
*
|
* Currently supported are:
|
* SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash
|
*
|
* MMC is not populated on this board.
|
* NAND support may be added in the future.
|
*/
|
#define SPL_BOOT_SPI_NOR_FLASH 1
|
#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH
|
|
/* Defines for SPL */
|
#define CONFIG_SPL_FRAMEWORK
|
#define CONFIG_SPL_SIZE (140 << 10)
|
#define CONFIG_SPL_TEXT_BASE 0x40000030
|
#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030)
|
|
#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)
|
#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
|
|
#ifdef CONFIG_SPL_BUILD
|
#define CONFIG_SYS_MALLOC_SIMPLE
|
#endif
|
|
#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
|
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
|
|
#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
|
/* SPL related SPI defines */
|
#define CONFIG_SPL_SPI_LOAD
|
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000
|
#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
|
#endif
|
|
/*
|
* mv-common.h should be defined after CMD configs since it used them
|
* to enable certain macros
|
*/
|
#include "mv-common.h"
|
#undef CONFIG_SYS_MAXARGS
|
#define CONFIG_SYS_MAXARGS 96
|
|
#endif /* _CONFIG_DB_88F6820_AMC_H */
|
