/*
|
* Copyright (C) 2007 Freescale Semiconductor, Inc.
|
* Kevin Lam <kevin.lam@freescale.com>
|
* Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
|
*
|
* SPDX-License-Identifier: GPL-2.0+
|
*/
|
|
#ifndef __CONFIG_H
|
#define __CONFIG_H
|
|
/*
|
* High Level Configuration Options
|
*/
|
#define CONFIG_E300 1 /* E300 family */
|
#define CONFIG_MPC837x 1 /* MPC837x CPU specific */
|
#define CONFIG_MPC837XERDB 1
|
|
#define CONFIG_SYS_TEXT_BASE 0xFE000000
|
|
#define CONFIG_MISC_INIT_R
|
#define CONFIG_HWCONFIG
|
|
/*
|
* On-board devices
|
*/
|
#define CONFIG_TSEC_ENET /* TSEC Ethernet support */
|
#define CONFIG_VSC7385_ENET
|
|
/*
|
* System Clock Setup
|
*/
|
#ifdef CONFIG_PCISLAVE
|
#define CONFIG_83XX_PCICLK 66666667 /* in HZ */
|
#else
|
#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
|
#define CONFIG_PCIE
|
#endif
|
|
#ifndef CONFIG_SYS_CLK_FREQ
|
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
|
#endif
|
|
/*
|
* Hardware Reset Configuration Word
|
*/
|
#define CONFIG_SYS_HRCW_LOW (\
|
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
|
HRCWL_DDR_TO_SCB_CLK_1X1 |\
|
HRCWL_SVCOD_DIV_2 |\
|
HRCWL_CSB_TO_CLKIN_5X1 |\
|
HRCWL_CORE_TO_CSB_2X1)
|
|
#ifdef CONFIG_PCISLAVE
|
#define CONFIG_SYS_HRCW_HIGH (\
|
HRCWH_PCI_AGENT |\
|
HRCWH_PCI1_ARBITER_DISABLE |\
|
HRCWH_CORE_ENABLE |\
|
HRCWH_FROM_0XFFF00100 |\
|
HRCWH_BOOTSEQ_DISABLE |\
|
HRCWH_SW_WATCHDOG_DISABLE |\
|
HRCWH_ROM_LOC_LOCAL_16BIT |\
|
HRCWH_RL_EXT_LEGACY |\
|
HRCWH_TSEC1M_IN_RGMII |\
|
HRCWH_TSEC2M_IN_RGMII |\
|
HRCWH_BIG_ENDIAN |\
|
HRCWH_LDP_CLEAR)
|
#else
|
#define CONFIG_SYS_HRCW_HIGH (\
|
HRCWH_PCI_HOST |\
|
HRCWH_PCI1_ARBITER_ENABLE |\
|
HRCWH_CORE_ENABLE |\
|
HRCWH_FROM_0X00000100 |\
|
HRCWH_BOOTSEQ_DISABLE |\
|
HRCWH_SW_WATCHDOG_DISABLE |\
|
HRCWH_ROM_LOC_LOCAL_16BIT |\
|
HRCWH_RL_EXT_LEGACY |\
|
HRCWH_TSEC1M_IN_RGMII |\
|
HRCWH_TSEC2M_IN_RGMII |\
|
HRCWH_BIG_ENDIAN |\
|
HRCWH_LDP_CLEAR)
|
#endif
|
|
/* System performance - define the value i.e. CONFIG_SYS_XXX
|
*/
|
|
/* Arbiter Configuration Register */
|
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
|
#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
|
|
/* System Priority Control Regsiter */
|
#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC1&2 emergency priority (0-3) */
|
|
/* System Clock Configuration Register */
|
#define CONFIG_SYS_SCCR_TSEC1CM 1 /* eTSEC1 clock mode (0-3) */
|
#define CONFIG_SYS_SCCR_TSEC2CM 1 /* eTSEC2 clock mode (0-3) */
|
#define CONFIG_SYS_SCCR_SATACM SCCR_SATACM_2 /* SATA1-4 clock mode (0-3) */
|
|
/*
|
* System IO Config
|
*/
|
#define CONFIG_SYS_SICRH 0x08200000
|
#define CONFIG_SYS_SICRL 0x00000000
|
|
/*
|
* Output Buffer Impedance
|
*/
|
#define CONFIG_SYS_OBIR 0x30100000
|
|
/*
|
* IMMR new address
|
*/
|
#define CONFIG_SYS_IMMR 0xE0000000
|
|
/*
|
* Device configurations
|
*/
|
|
/* Vitesse 7385 */
|
|
#ifdef CONFIG_VSC7385_ENET
|
|
#define CONFIG_TSEC2
|
|
/* The flash address and size of the VSC7385 firmware image */
|
#define CONFIG_VSC7385_IMAGE 0xFE7FE000
|
#define CONFIG_VSC7385_IMAGE_SIZE 8192
|
|
#endif
|
|
/*
|
* DDR Setup
|
*/
|
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
|
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
|
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x03000000
|
#define CONFIG_SYS_83XX_DDR_USES_CS0
|
|
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN | DDRCDR_ODT | DDRCDR_Q_DRN)
|
|
#undef CONFIG_DDR_ECC /* support DDR ECC function */
|
#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
|
|
#undef CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */
|
|
/*
|
* Manually set up DDR parameters
|
*/
|
#define CONFIG_SYS_DDR_SIZE 256 /* MB */
|
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
|
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
|
| CSCONFIG_ODT_WR_ONLY_CURRENT \
|
| CSCONFIG_ROW_BIT_13 \
|
| CSCONFIG_COL_BIT_10)
|
|
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
|
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
|
| (0 << TIMING_CFG0_WRT_SHIFT) \
|
| (0 << TIMING_CFG0_RRT_SHIFT) \
|
| (0 << TIMING_CFG0_WWT_SHIFT) \
|
| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
|
| (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
|
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
|
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
|
/* 0x00260802 */ /* DDR400 */
|
#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
|
| (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
|
| (3 << TIMING_CFG1_ACTTORW_SHIFT) \
|
| (7 << TIMING_CFG1_CASLAT_SHIFT) \
|
| (13 << TIMING_CFG1_REFREC_SHIFT) \
|
| (3 << TIMING_CFG1_WRREC_SHIFT) \
|
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
|
| (2 << TIMING_CFG1_WRTORD_SHIFT))
|
/* 0x3937d322 */
|
#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
|
| (5 << TIMING_CFG2_CPO_SHIFT) \
|
| (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
|
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
|
| (3 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
|
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
|
| (8 << TIMING_CFG2_FOUR_ACT_SHIFT))
|
/* 0x02984cc8 */
|
|
#define CONFIG_SYS_DDR_INTERVAL ((1024 << SDRAM_INTERVAL_REFINT_SHIFT) \
|
| (0 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
|
/* 0x06090100 */
|
|
#if defined(CONFIG_DDR_2T_TIMING)
|
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
|
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
|
| SDRAM_CFG_32_BE \
|
| SDRAM_CFG_2T_EN)
|
/* 0x43088000 */
|
#else
|
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
|
| SDRAM_CFG_SDRAM_TYPE_DDR2)
|
/* 0x43000000 */
|
#endif
|
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */
|
#define CONFIG_SYS_DDR_MODE ((0x0406 << SDRAM_MODE_ESD_SHIFT) \
|
| (0x0442 << SDRAM_MODE_SD_SHIFT))
|
/* 0x04400442 */ /* DDR400 */
|
#define CONFIG_SYS_DDR_MODE2 0x00000000
|
|
/*
|
* Memory test
|
*/
|
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
|
#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */
|
#define CONFIG_SYS_MEMTEST_END 0x0ef70010
|
|
/*
|
* The reserved memory
|
*/
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
|
#define CONFIG_SYS_RAMBOOT
|
#else
|
#undef CONFIG_SYS_RAMBOOT
|
#endif
|
|
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
|
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
|
|
/*
|
* Initial RAM Base Address Setup
|
*/
|
#define CONFIG_SYS_INIT_RAM_LOCK 1
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
|
#define CONFIG_SYS_GBL_DATA_OFFSET \
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
/*
|
* Local Bus Configuration & Clock Setup
|
*/
|
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
|
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
|
#define CONFIG_SYS_LBC_LBCR 0x00000000
|
#define CONFIG_FSL_ELBC 1
|
|
/*
|
* FLASH on the Local Bus
|
*/
|
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
|
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
|
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
|
#define CONFIG_SYS_FLASH_SIZE 8 /* max FLASH size is 32M */
|
|
#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
|
#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
|
|
/* Window base at flash base */
|
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
|
#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8 MB window size */
|
|
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
|
| BR_PS_16 /* 16 bit port */ \
|
| BR_MS_GPCM /* MSEL = GPCM */ \
|
| BR_V) /* valid */
|
#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
|
| OR_GPCM_XACS \
|
| OR_GPCM_SCY_9 \
|
| OR_GPCM_EHTR_SET \
|
| OR_GPCM_EAD)
|
/* 0xFF800191 */
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
|
|
#undef CONFIG_SYS_FLASH_CHECKSUM
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
/*
|
* NAND Flash on the Local Bus
|
*/
|
#define CONFIG_SYS_NAND_BASE 0xE0600000
|
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE \
|
| BR_DECC_CHK_GEN /* Use HW ECC */ \
|
| BR_PS_8 /* 8 bit port */ \
|
| BR_MS_FCM /* MSEL = FCM */ \
|
| BR_V) /* valid */
|
#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \
|
| OR_FCM_CSCT \
|
| OR_FCM_CST \
|
| OR_FCM_CHT \
|
| OR_FCM_SCY_1 \
|
| OR_FCM_TRLX \
|
| OR_FCM_EHTR)
|
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
|
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
|
|
/* Vitesse 7385 */
|
|
#define CONFIG_SYS_VSC7385_BASE 0xF0000000
|
|
#ifdef CONFIG_VSC7385_ENET
|
|
#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VSC7385_BASE \
|
| BR_PS_8 \
|
| BR_MS_GPCM \
|
| BR_V)
|
/* 0xF0000801 */
|
#define CONFIG_SYS_OR2_PRELIM (OR_AM_128KB \
|
| OR_GPCM_CSNT \
|
| OR_GPCM_XACS \
|
| OR_GPCM_SCY_15 \
|
| OR_GPCM_SETA \
|
| OR_GPCM_TRLX_SET \
|
| OR_GPCM_EHTR_SET \
|
| OR_GPCM_EAD)
|
/* 0xfffe09ff */
|
|
/* Access Base */
|
#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE
|
#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_128KB)
|
|
#endif
|
|
/*
|
* Serial Port
|
*/
|
#define CONFIG_CONS_INDEX 1
|
#define CONFIG_SYS_NS16550_SERIAL
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
|
|
/* SERDES */
|
#define CONFIG_FSL_SERDES
|
#define CONFIG_FSL_SERDES1 0xe3000
|
#define CONFIG_FSL_SERDES2 0xe3100
|
|
/* I2C */
|
#define CONFIG_SYS_I2C
|
#define CONFIG_SYS_I2C_FSL
|
#define CONFIG_SYS_FSL_I2C_SPEED 400000
|
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
|
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
|
|
/*
|
* Config on-board RTC
|
*/
|
#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
|
|
/*
|
* General PCI
|
* Addresses are mapped 1-1.
|
*/
|
#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
|
#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
|
#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */
|
#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
|
#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
|
#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */
|
#define CONFIG_SYS_PCI_IO_BASE 0x00000000
|
#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
|
#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */
|
|
#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
|
#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
|
#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
|
|
#define CONFIG_SYS_PCIE1_BASE 0xA0000000
|
#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000
|
#define CONFIG_SYS_PCIE1_CFG_SIZE 0x08000000
|
#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000
|
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000
|
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
|
#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
|
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000
|
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
|
|
#define CONFIG_SYS_PCIE2_BASE 0xC0000000
|
#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000
|
#define CONFIG_SYS_PCIE2_CFG_SIZE 0x08000000
|
#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000
|
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000
|
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
|
#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
|
#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000
|
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
|
|
#ifdef CONFIG_PCI
|
#define CONFIG_PCI_INDIRECT_BRIDGE
|
|
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
|
#endif /* CONFIG_PCI */
|
|
/*
|
* TSEC
|
*/
|
#ifdef CONFIG_TSEC_ENET
|
|
#define CONFIG_GMII /* MII PHY management */
|
|
#define CONFIG_TSEC1
|
|
#ifdef CONFIG_TSEC1
|
#define CONFIG_HAS_ETH0
|
#define CONFIG_TSEC1_NAME "TSEC0"
|
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
|
#define TSEC1_PHY_ADDR 2
|
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
#define TSEC1_PHYIDX 0
|
#endif
|
|
#ifdef CONFIG_TSEC2
|
#define CONFIG_HAS_ETH1
|
#define CONFIG_TSEC2_NAME "TSEC1"
|
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
|
#define TSEC2_PHY_ADDR 0x1c
|
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
#define TSEC2_PHYIDX 0
|
#endif
|
|
/* Options are: TSEC[0-1] */
|
#define CONFIG_ETHPRIME "TSEC0"
|
|
#endif
|
|
/*
|
* SATA
|
*/
|
#define CONFIG_LIBATA
|
#define CONFIG_FSL_SATA
|
|
#define CONFIG_SYS_SATA_MAX_DEVICE 2
|
#define CONFIG_SATA1
|
#define CONFIG_SYS_SATA1_OFFSET 0x18000
|
#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
|
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
|
#define CONFIG_SATA2
|
#define CONFIG_SYS_SATA2_OFFSET 0x19000
|
#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
|
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
|
|
#ifdef CONFIG_FSL_SATA
|
#define CONFIG_LBA48
|
#endif
|
|
/*
|
* Environment
|
*/
|
#ifndef CONFIG_SYS_RAMBOOT
|
#define CONFIG_ENV_ADDR \
|
(CONFIG_SYS_MONITOR_BASE+CONFIG_SYS_MONITOR_LEN)
|
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for env */
|
#define CONFIG_ENV_SIZE 0x4000
|
#else
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-0x1000)
|
#define CONFIG_ENV_SIZE 0x2000
|
#endif
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
/*
|
* BOOTP options
|
*/
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
#define CONFIG_BOOTP_BOOTPATH
|
#define CONFIG_BOOTP_GATEWAY
|
#define CONFIG_BOOTP_HOSTNAME
|
|
/*
|
* Command line configuration.
|
*/
|
|
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
|
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
#ifdef CONFIG_MMC
|
#define CONFIG_FSL_ESDHC
|
#define CONFIG_FSL_ESDHC_PIN_MUX
|
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
|
#endif
|
|
/*
|
* Miscellaneous configurable options
|
*/
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
/*
|
* For booting Linux, the board info and command line data
|
* have to be in the first 256 MB of memory, since this is
|
* the maximum mapped by the Linux kernel during initialization.
|
*/
|
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
|
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
|
/*
|
* Core HID Setup
|
*/
|
#define CONFIG_SYS_HID0_INIT 0x000000000
|
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \
|
| HID0_ENABLE_INSTRUCTION_CACHE)
|
#define CONFIG_SYS_HID2 HID2_HBE
|
|
/*
|
* MMU Setup
|
*/
|
|
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
|
|
/* DDR: cache cacheable */
|
#define CONFIG_SYS_SDRAM_LOWER CONFIG_SYS_SDRAM_BASE
|
#define CONFIG_SYS_SDRAM_UPPER (CONFIG_SYS_SDRAM_BASE + 0x10000000)
|
|
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_LOWER \
|
| BATL_PP_RW \
|
| BATL_MEMCOHERENCE)
|
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_LOWER \
|
| BATU_BL_256M \
|
| BATU_VS \
|
| BATU_VP)
|
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
|
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
|
|
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_SDRAM_UPPER \
|
| BATL_PP_RW \
|
| BATL_MEMCOHERENCE)
|
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_SDRAM_UPPER \
|
| BATU_BL_256M \
|
| BATU_VS \
|
| BATU_VP)
|
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
|
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
|
|
/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
|
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_IMMR \
|
| BATL_PP_RW \
|
| BATL_CACHEINHIBIT \
|
| BATL_GUARDEDSTORAGE)
|
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_IMMR \
|
| BATU_BL_8M \
|
| BATU_VS \
|
| BATU_VP)
|
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
|
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
|
|
/* L2 Switch: cache-inhibit and guarded */
|
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_VSC7385_BASE \
|
| BATL_PP_RW \
|
| BATL_CACHEINHIBIT \
|
| BATL_GUARDEDSTORAGE)
|
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_VSC7385_BASE \
|
| BATU_BL_128K \
|
| BATU_VS \
|
| BATU_VP)
|
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
|
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
|
|
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
|
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_FLASH_BASE \
|
| BATL_PP_RW \
|
| BATL_MEMCOHERENCE)
|
#define CONFIG_SYS_IBAT4U (CONFIG_SYS_FLASH_BASE \
|
| BATU_BL_32M \
|
| BATU_VS \
|
| BATU_VP)
|
#define CONFIG_SYS_DBAT4L (CONFIG_SYS_FLASH_BASE \
|
| BATL_PP_RW \
|
| BATL_CACHEINHIBIT \
|
| BATL_GUARDEDSTORAGE)
|
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
|
|
/* Stack in dcache: cacheable, no memory coherence */
|
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
|
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR \
|
| BATU_BL_128K \
|
| BATU_VS \
|
| BATU_VP)
|
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
|
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
|
|
#ifdef CONFIG_PCI
|
/* PCI MEM space: cacheable */
|
#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS \
|
| BATL_PP_RW \
|
| BATL_MEMCOHERENCE)
|
#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS \
|
| BATU_BL_256M \
|
| BATU_VS \
|
| BATU_VP)
|
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
|
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
|
/* PCI MMIO space: cache-inhibit and guarded */
|
#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS \
|
| BATL_PP_RW \
|
| BATL_CACHEINHIBIT \
|
| BATL_GUARDEDSTORAGE)
|
#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS \
|
| BATU_BL_256M \
|
| BATU_VS \
|
| BATU_VP)
|
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
|
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
|
#else
|
#define CONFIG_SYS_IBAT6L (0)
|
#define CONFIG_SYS_IBAT6U (0)
|
#define CONFIG_SYS_IBAT7L (0)
|
#define CONFIG_SYS_IBAT7U (0)
|
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
|
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
|
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
|
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
|
#endif
|
|
#if defined(CONFIG_CMD_KGDB)
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
|
#endif
|
|
/*
|
* Environment Configuration
|
*/
|
#define CONFIG_ENV_OVERWRITE
|
|
#define CONFIG_HAS_FSL_DR_USB
|
#define CONFIG_USB_EHCI_FSL
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
#define CONFIG_NETDEV "eth1"
|
|
#define CONFIG_HOSTNAME mpc837x_rdb
|
#define CONFIG_ROOTPATH "/nfsroot"
|
#define CONFIG_RAMDISKFILE "rootfs.ext2.gz.uboot"
|
#define CONFIG_BOOTFILE "uImage"
|
/* U-Boot image on TFTP server */
|
#define CONFIG_UBOOTPATH "u-boot.bin"
|
#define CONFIG_FDTFILE "mpc8379_rdb.dtb"
|
|
/* default location for tftp and bootm */
|
#define CONFIG_LOADADDR 800000
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
"netdev=" CONFIG_NETDEV "\0" \
|
"uboot=" CONFIG_UBOOTPATH "\0" \
|
"tftpflash=tftp $loadaddr $uboot;" \
|
"protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
|
" +$filesize; " \
|
"erase " __stringify(CONFIG_SYS_TEXT_BASE) \
|
" +$filesize; " \
|
"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
|
" $filesize; " \
|
"protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
|
" +$filesize; " \
|
"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
|
" $filesize\0" \
|
"fdtaddr=780000\0" \
|
"fdtfile=" CONFIG_FDTFILE "\0" \
|
"ramdiskaddr=1000000\0" \
|
"ramdiskfile=" CONFIG_RAMDISKFILE "\0" \
|
"console=ttyS0\0" \
|
"setbootargs=setenv bootargs " \
|
"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
|
"setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
|
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
|
"$netdev:off " \
|
"root=$rootdev rw console=$console,$baudrate $othbootargs\0"
|
|
#define CONFIG_NFSBOOTCOMMAND \
|
"setenv rootdev /dev/nfs;" \
|
"run setbootargs;" \
|
"run setipargs;" \
|
"tftp $loadaddr $bootfile;" \
|
"tftp $fdtaddr $fdtfile;" \
|
"bootm $loadaddr - $fdtaddr"
|
|
#define CONFIG_RAMBOOTCOMMAND \
|
"setenv rootdev /dev/ram;" \
|
"run setbootargs;" \
|
"tftp $ramdiskaddr $ramdiskfile;" \
|
"tftp $loadaddr $bootfile;" \
|
"tftp $fdtaddr $fdtfile;" \
|
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
|
#endif /* __CONFIG_H */
|
