/*
|
* Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
|
* Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
|
*
|
*
|
* SPDX-License-Identifier: GPL-2.0+
|
*/
|
|
#ifndef __CONFIG_H
|
#define __CONFIG_H
|
|
/*
|
* High Level Configuration Options
|
*/
|
#define CONFIG_E300 1 /* E300 family */
|
#define CONFIG_MPC830x 1 /* MPC830x family */
|
#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
|
#define CONFIG_MPC8308RDB 1 /* MPC8308RDB board specific */
|
|
#define CONFIG_SYS_TEXT_BASE 0xFE000000
|
|
#define CONFIG_MISC_INIT_R
|
|
#ifdef CONFIG_MMC
|
#define CONFIG_FSL_ESDHC
|
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
|
#define CONFIG_SYS_FSL_ESDHC_USE_PIO
|
#endif
|
|
/*
|
* On-board devices
|
*
|
* TSEC1 is SoC TSEC
|
* TSEC2 is VSC switch
|
*/
|
#define CONFIG_TSEC1
|
#define CONFIG_VSC7385_ENET
|
|
/*
|
* System Clock Setup
|
*/
|
#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
|
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
|
|
/*
|
* Hardware Reset Configuration Word
|
* if CLKIN is 66.66MHz, then
|
* CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
|
* We choose the A type silicon as default, so the core is 400Mhz.
|
*/
|
#define CONFIG_SYS_HRCW_LOW (\
|
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
|
HRCWL_DDR_TO_SCB_CLK_2X1 |\
|
HRCWL_SVCOD_DIV_2 |\
|
HRCWL_CSB_TO_CLKIN_4X1 |\
|
HRCWL_CORE_TO_CSB_3X1)
|
/*
|
* There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
|
* in 8308's HRCWH according to the manual, but original Freescale's
|
* code has them and I've expirienced some problems using the board
|
* with BDI3000 attached when I've tried to set these bits to zero
|
* (UART doesn't work after the 'reset run' command).
|
*/
|
#define CONFIG_SYS_HRCW_HIGH (\
|
HRCWH_PCI_HOST |\
|
HRCWH_PCI1_ARBITER_ENABLE |\
|
HRCWH_CORE_ENABLE |\
|
HRCWH_FROM_0X00000100 |\
|
HRCWH_BOOTSEQ_DISABLE |\
|
HRCWH_SW_WATCHDOG_DISABLE |\
|
HRCWH_ROM_LOC_LOCAL_16BIT |\
|
HRCWH_RL_EXT_LEGACY |\
|
HRCWH_TSEC1M_IN_RGMII |\
|
HRCWH_TSEC2M_IN_RGMII |\
|
HRCWH_BIG_ENDIAN)
|
|
/*
|
* System IO Config
|
*/
|
#define CONFIG_SYS_SICRH (\
|
SICRH_ESDHC_A_SD |\
|
SICRH_ESDHC_B_SD |\
|
SICRH_ESDHC_C_SD |\
|
SICRH_GPIO_A_TSEC2 |\
|
SICRH_GPIO_B_TSEC2_GTX_CLK125 |\
|
SICRH_IEEE1588_A_GPIO |\
|
SICRH_USB |\
|
SICRH_GTM_GPIO |\
|
SICRH_IEEE1588_B_GPIO |\
|
SICRH_ETSEC2_CRS |\
|
SICRH_GPIOSEL_1 |\
|
SICRH_TMROBI_V3P3 |\
|
SICRH_TSOBI1_V2P5 |\
|
SICRH_TSOBI2_V2P5) /* 0x01b7d103 */
|
#define CONFIG_SYS_SICRL (\
|
SICRL_SPI_PF0 |\
|
SICRL_UART_PF0 |\
|
SICRL_IRQ_PF0 |\
|
SICRL_I2C2_PF0 |\
|
SICRL_ETSEC1_GTX_CLK125) /* 0x00000040 */
|
|
/*
|
* IMMR new address
|
*/
|
#define CONFIG_SYS_IMMR 0xE0000000
|
|
/*
|
* SERDES
|
*/
|
#define CONFIG_FSL_SERDES
|
#define CONFIG_FSL_SERDES1 0xe3000
|
|
/*
|
* Arbiter Setup
|
*/
|
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
|
#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
|
#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
|
|
/*
|
* DDR Setup
|
*/
|
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
|
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
|
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
|
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
|
| DDRCDR_PZ_LOZ \
|
| DDRCDR_NZ_LOZ \
|
| DDRCDR_ODT \
|
| DDRCDR_Q_DRN)
|
/* 0x7b880001 */
|
/*
|
* Manually set up DDR parameters
|
* consist of two chips HY5PS12621BFP-C4 from HYNIX
|
*/
|
|
#define CONFIG_SYS_DDR_SIZE 128 /* MB */
|
|
#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
|
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
|
| CSCONFIG_ODT_RD_NEVER \
|
| CSCONFIG_ODT_WR_ONLY_CURRENT \
|
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
|
/* 0x80010102 */
|
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
|
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
|
| (0 << TIMING_CFG0_WRT_SHIFT) \
|
| (0 << TIMING_CFG0_RRT_SHIFT) \
|
| (0 << TIMING_CFG0_WWT_SHIFT) \
|
| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
|
| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
|
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
|
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
|
/* 0x00220802 */
|
#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
|
| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
|
| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
|
| (5 << TIMING_CFG1_CASLAT_SHIFT) \
|
| (6 << TIMING_CFG1_REFREC_SHIFT) \
|
| (2 << TIMING_CFG1_WRREC_SHIFT) \
|
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
|
| (2 << TIMING_CFG1_WRTORD_SHIFT))
|
/* 0x27256222 */
|
#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
|
| (4 << TIMING_CFG2_CPO_SHIFT) \
|
| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
|
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
|
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
|
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
|
| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
|
/* 0x121048c5 */
|
#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
|
| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
|
/* 0x03600100 */
|
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
|
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
|
| SDRAM_CFG_DBW_32)
|
/* 0x43080000 */
|
|
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
|
#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
|
| (0x0232 << SDRAM_MODE_SD_SHIFT))
|
/* ODT 150ohm CL=3, AL=1 on SDRAM */
|
#define CONFIG_SYS_DDR_MODE2 0x00000000
|
|
/*
|
* Memory test
|
*/
|
#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */
|
#define CONFIG_SYS_MEMTEST_END 0x07f00000
|
|
/*
|
* The reserved memory
|
*/
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
|
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
|
|
/*
|
* Initial RAM Base Address Setup
|
*/
|
#define CONFIG_SYS_INIT_RAM_LOCK 1
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
|
#define CONFIG_SYS_GBL_DATA_OFFSET \
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
/*
|
* Local Bus Configuration & Clock Setup
|
*/
|
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
|
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
|
#define CONFIG_SYS_LBC_LBCR 0x00040000
|
|
/*
|
* FLASH on the Local Bus
|
*/
|
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
|
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
|
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
|
|
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
|
#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */
|
#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
|
|
/* Window base at flash base */
|
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
|
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
|
|
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
|
| BR_PS_16 /* 16 bit port */ \
|
| BR_MS_GPCM /* MSEL = GPCM */ \
|
| BR_V) /* valid */
|
#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
|
| OR_UPM_XAM \
|
| OR_GPCM_CSNT \
|
| OR_GPCM_ACS_DIV2 \
|
| OR_GPCM_XACS \
|
| OR_GPCM_SCY_15 \
|
| OR_GPCM_TRLX_SET \
|
| OR_GPCM_EHTR_SET)
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
|
/* 127 64KB sectors and 8 8KB top sectors per device */
|
#define CONFIG_SYS_MAX_FLASH_SECT 135
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
/*
|
* NAND Flash on the Local Bus
|
*/
|
#define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */
|
#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */
|
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE \
|
| BR_DECC_CHK_GEN /* Use HW ECC */ \
|
| BR_PS_8 /* 8 bit Port */ \
|
| BR_MS_FCM /* MSEL = FCM */ \
|
| BR_V) /* valid */
|
#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
|
| OR_FCM_CSCT \
|
| OR_FCM_CST \
|
| OR_FCM_CHT \
|
| OR_FCM_SCY_1 \
|
| OR_FCM_TRLX \
|
| OR_FCM_EHTR)
|
/* 0xFFFF8396 */
|
|
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
|
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
|
|
#ifdef CONFIG_VSC7385_ENET
|
#define CONFIG_TSEC2
|
/* VSC7385 Base address on CS2 */
|
#define CONFIG_SYS_VSC7385_BASE 0xF0000000
|
#define CONFIG_SYS_VSC7385_SIZE (128 * 1024) /* 0x00020000 */
|
#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VSC7385_BASE \
|
| BR_PS_8 /* 8-bit port */ \
|
| BR_MS_GPCM /* MSEL = GPCM */ \
|
| BR_V) /* valid */
|
/* 0xF0000801 */
|
#define CONFIG_SYS_OR2_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VSC7385_SIZE) \
|
| OR_GPCM_CSNT \
|
| OR_GPCM_XACS \
|
| OR_GPCM_SCY_15 \
|
| OR_GPCM_SETA \
|
| OR_GPCM_TRLX_SET \
|
| OR_GPCM_EHTR_SET)
|
/* 0xFFFE09FF */
|
/* Access window base at VSC7385 base */
|
#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE
|
/* Access window size 128K */
|
#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_128KB)
|
/* The flash address and size of the VSC7385 firmware image */
|
#define CONFIG_VSC7385_IMAGE 0xFE7FE000
|
#define CONFIG_VSC7385_IMAGE_SIZE 8192
|
#endif
|
/*
|
* Serial Port
|
*/
|
#define CONFIG_CONS_INDEX 1
|
#define CONFIG_SYS_NS16550_SERIAL
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
|
|
/* I2C */
|
#define CONFIG_SYS_I2C
|
#define CONFIG_SYS_I2C_FSL
|
#define CONFIG_SYS_FSL_I2C_SPEED 400000
|
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
|
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
|
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
|
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
|
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
|
|
/*
|
* SPI on header J8
|
*
|
* WARNING: enabling this will break TSEC2 (connected to the Vitesse switch)
|
* due to a pinmux conflict between GPIO9 (SPI chip select )and the TSEC2 pins.
|
*/
|
#ifdef CONFIG_MPC8XXX_SPI
|
#define CONFIG_USE_SPIFLASH
|
#endif
|
|
/*
|
* Board info - revision and where boot from
|
*/
|
#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39
|
|
/*
|
* Config on-board RTC
|
*/
|
#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
|
|
/*
|
* General PCI
|
* Addresses are mapped 1-1.
|
*/
|
#define CONFIG_SYS_PCIE1_BASE 0xA0000000
|
#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
|
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
|
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
|
#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
|
#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
|
#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
|
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
|
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
|
|
/* enable PCIE clock */
|
#define CONFIG_SYS_SCCR_PCIEXP1CM 1
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE
|
#define CONFIG_PCIE
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
|
#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
|
|
/*
|
* TSEC
|
*/
|
#define CONFIG_TSEC_ENET /* TSEC ethernet support */
|
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
|
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
|
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
|
#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
|
|
/*
|
* TSEC ethernet configuration
|
*/
|
#define CONFIG_MII 1 /* MII PHY management */
|
#define CONFIG_TSEC1_NAME "eTSEC0"
|
#define CONFIG_TSEC2_NAME "eTSEC1"
|
#define TSEC1_PHY_ADDR 2
|
#define TSEC2_PHY_ADDR 1
|
#define TSEC1_PHYIDX 0
|
#define TSEC2_PHYIDX 0
|
#define TSEC1_FLAGS TSEC_GIGABIT
|
#define TSEC2_FLAGS TSEC_GIGABIT
|
|
/* Options are: eTSEC[0-1] */
|
#define CONFIG_ETHPRIME "eTSEC0"
|
|
/*
|
* Environment
|
*/
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
|
CONFIG_SYS_MONITOR_LEN)
|
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
|
#define CONFIG_ENV_SIZE 0x2000
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
|
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
/*
|
* BOOTP options
|
*/
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
#define CONFIG_BOOTP_BOOTPATH
|
#define CONFIG_BOOTP_GATEWAY
|
#define CONFIG_BOOTP_HOSTNAME
|
|
/*
|
* Command line configuration.
|
*/
|
|
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
|
|
/*
|
* Miscellaneous configurable options
|
*/
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
/* Boot Argument Buffer Size */
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
|
|
/*
|
* For booting Linux, the board info and command line data
|
* have to be in the first 256 MB of memory, since this is
|
* the maximum mapped by the Linux kernel during initialization.
|
*/
|
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
|
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
|
/*
|
* Core HID Setup
|
*/
|
#define CONFIG_SYS_HID0_INIT 0x000000000
|
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
|
HID0_ENABLE_INSTRUCTION_CACHE | \
|
HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
|
#define CONFIG_SYS_HID2 HID2_HBE
|
|
/*
|
* MMU Setup
|
*/
|
|
/* DDR: cache cacheable */
|
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
|
BATL_MEMCOHERENCE)
|
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
|
BATU_VS | BATU_VP)
|
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
|
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
|
|
/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
|
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \
|
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
|
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
|
BATU_VP)
|
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
|
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
|
|
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
|
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
|
BATL_MEMCOHERENCE)
|
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
|
BATU_VS | BATU_VP)
|
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
|
BATL_CACHEINHIBIT | \
|
BATL_GUARDEDSTORAGE)
|
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
|
|
/* Stack in dcache: cacheable, no memory coherence */
|
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
|
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
|
BATU_VS | BATU_VP)
|
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
|
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
|
|
/*
|
* Environment Configuration
|
*/
|
|
#define CONFIG_ENV_OVERWRITE
|
|
#if defined(CONFIG_TSEC_ENET)
|
#define CONFIG_HAS_ETH0
|
#define CONFIG_HAS_ETH1
|
#endif
|
|
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
"netdev=eth0\0" \
|
"consoledev=ttyS0\0" \
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
"nfsroot=${serverip}:${rootpath}\0" \
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
"addip=setenv bootargs ${bootargs} " \
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
":${hostname}:${netdev}:off panic=1\0" \
|
"addtty=setenv bootargs ${bootargs}" \
|
" console=${consoledev},${baudrate}\0" \
|
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
|
"addmisc=setenv bootargs ${bootargs}\0" \
|
"kernel_addr=FE080000\0" \
|
"fdt_addr=FE280000\0" \
|
"ramdisk_addr=FE290000\0" \
|
"u-boot=mpc8308rdb/u-boot.bin\0" \
|
"kernel_addr_r=1000000\0" \
|
"fdt_addr_r=C00000\0" \
|
"hostname=mpc8308rdb\0" \
|
"bootfile=mpc8308rdb/uImage\0" \
|
"fdtfile=mpc8308rdb/mpc8308rdb.dtb\0" \
|
"rootpath=/opt/eldk-4.2/ppc_6xx\0" \
|
"flash_self=run ramargs addip addtty addmtd addmisc;" \
|
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
|
"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
|
"bootm ${kernel_addr} - ${fdt_addr}\0" \
|
"net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
|
"tftp ${fdt_addr_r} ${fdtfile};" \
|
"run nfsargs addip addtty addmtd addmisc;" \
|
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
|
"bootcmd=run flash_self\0" \
|
"load=tftp ${loadaddr} ${u-boot}\0" \
|
"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
|
" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
|
" +${filesize};cp.b ${fileaddr} " \
|
__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
|
"upd=run load update\0" \
|
|
#endif /* __CONFIG_H */
|
