/*
|
* Copyright (C) 2016, Bin Meng <bmeng.cn@gmail.com>
|
*
|
* SPDX-License-Identifier: GPL-2.0+
|
*/
|
|
#ifndef _SMSC_SIO1007_H_
|
#define _SMSC_SIO1007_H_
|
|
/*
|
* The I/O base address of SIO1007 at power-up is determined by the SYSOPT0
|
* and SYSOPT1 pins at the deasserting edge of PCIRST#. The combination of
|
* SYSOPT0 and SYSOPT1 determines one of the following addresses.
|
*/
|
#define SIO1007_IOPORT0 0x002e
|
#define SIO1007_IOPORT1 0x004e
|
#define SIO1007_IOPORT2 0x162e
|
#define SIO1007_IOPORT3 0x164e
|
|
/* SIO1007 registers */
|
|
#define DEV_POWER_CTRL 0x02
|
#define UART1_POWER_ON (1 << 3)
|
#define UART2_POWER_ON (1 << 7)
|
|
#define UART1_IOBASE 0x24
|
#define UART2_IOBASE 0x25
|
#define UART_IRQ 0x28
|
|
#define RTR_IOBASE_HIGH 0x21
|
#define RTR_IOBASE_LOW 0x30
|
|
#define GPIO0_DIR 0x31
|
#define GPIO1_DIR 0x35
|
#define GPIO_DIR_INPUT 0
|
#define GPIO_DIR_OUTPUT 1
|
|
#define GPIO0_POL 0x32
|
#define GPIO1_POL 0x36
|
#define GPIO_POL_NO_INVERT 0
|
#define GPIO_POL_INVERT 1
|
|
#define GPIO0_TYPE 0x33
|
#define GPIO1_TYPE 0x37
|
#define GPIO_TYPE_PUSH_PULL 0
|
#define GPIO_TYPE_OPEN_DRAIN 1
|
|
#define DEV_ACTIVATE 0x3a
|
#define RTR_EN (1 << 1)
|
|
/* Runtime register offset */
|
|
#define GPIO0_DATA 0xc
|
#define GPIO1_DATA 0xe
|
|
/* Number of serial ports supported */
|
#define SIO1007_UART_NUM 2
|
|
/* Number of gpio pins supported */
|
#define GPIO_NUM_PER_GROUP 8
|
#define GPIO_GROUP_NUM 2
|
#define SIO1007_GPIO_NUM (GPIO_NUM_PER_GROUP * GPIO_GROUP_NUM)
|
|
/**
|
* Configure the I/O port address of the specified serial device and
|
* enable the serial device.
|
*
|
* @port: SIO1007 I/O port address
|
* @num: serial device number (0 or 1)
|
* @iobase: processor I/O port address to assign to this serial device
|
* @irq: processor IRQ number to assign to this serial device
|
*/
|
void sio1007_enable_serial(int port, int num, int iobase, int irq);
|
|
/**
|
* Configure the I/O port address of the runtime register block and
|
* enable the address decoding.
|
*
|
* @port: SIO1007 I/O port address
|
* @iobase: processor I/O port address to assign to the runtime registers
|
*/
|
void sio1007_enable_runtime(int port, int iobase);
|
|
/**
|
* Configure the direction/polority/type of a specified GPIO pin
|
*
|
* @port: SIO1007 I/O port address
|
* @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
|
* @dir: GPIO_DIR_INPUT or GPIO_DIR_OUTPUT
|
* @pol: GPIO_POL_NO_INVERT or GPIO_POL_INVERT
|
* @type: GPIO_TYPE_PUSH_PULL or GPIO_TYPE_OPEN_DRAIN
|
*/
|
void sio1007_gpio_config(int port, int gpio, int dir, int pol, int type);
|
|
/**
|
* Get a GPIO pin value.
|
* This will work whether the GPIO is an input or an output.
|
*
|
* @port: runtime register block I/O port address
|
* @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
|
* @return: 0 if low, 1 if high, -EINVAL if gpio number is invalid
|
*/
|
int sio1007_gpio_get_value(int port, int gpio);
|
|
/**
|
* Set a GPIO pin value.
|
* This will only work when the GPIO is configured as an output.
|
*
|
* @port: runtime register block I/O port address
|
* @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
|
* @val: 0 if low, 1 if high
|
*/
|
void sio1007_gpio_set_value(int port, int gpio, int val);
|
|
#endif /* _SMSC_SIO1007_H_ */
|
