/*
|
* Bluegiga APX4 Development Kit
|
*
|
* Copyright (C) 2012 Bluegiga Technologies Oy
|
*
|
* Authors:
|
* Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
|
* Lauri Hintsala <lauri.hintsala@bluegiga.com>
|
*
|
* Based on m28evk.c:
|
* Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
|
* on behalf of DENX Software Engineering GmbH
|
*
|
* SPDX-License-Identifier: GPL-2.0+
|
*/
|
|
#include <common.h>
|
#include <asm/gpio.h>
|
#include <asm/io.h>
|
#include <asm/setup.h>
|
#include <asm/arch/imx-regs.h>
|
#include <asm/arch/iomux-mx28.h>
|
#include <asm/arch/clock.h>
|
#include <asm/arch/sys_proto.h>
|
#include <linux/mii.h>
|
#include <miiphy.h>
|
#include <netdev.h>
|
#include <errno.h>
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
/* Functions */
|
int board_early_init_f(void)
|
{
|
/* IO0 clock at 480MHz */
|
mxs_set_ioclk(MXC_IOCLK0, 480000);
|
/* IO1 clock at 480MHz */
|
mxs_set_ioclk(MXC_IOCLK1, 480000);
|
|
/* SSP0 clock at 96MHz */
|
mxs_set_sspclk(MXC_SSPCLK0, 96000, 0);
|
|
return 0;
|
}
|
|
int dram_init(void)
|
{
|
return mxs_dram_init();
|
}
|
|
int board_init(void)
|
{
|
/* Adress of boot parameters */
|
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
|
|
return 0;
|
}
|
|
#ifdef CONFIG_CMD_MMC
|
int board_mmc_init(bd_t *bis)
|
{
|
return mxsmmc_initialize(bis, 0, NULL, NULL);
|
}
|
#endif
|
|
|
#ifdef CONFIG_CMD_NET
|
|
#define MII_PHY_CTRL2 0x1f
|
int fecmxc_mii_postcall(int phy)
|
{
|
/* change PHY RMII clock to 50MHz */
|
miiphy_write("FEC", 0, MII_PHY_CTRL2, 0x8180);
|
|
return 0;
|
}
|
|
int board_eth_init(bd_t *bis)
|
{
|
int ret;
|
struct eth_device *dev;
|
|
ret = cpu_eth_init(bis);
|
if (ret) {
|
printf("FEC MXS: Unable to init FEC clocks\n");
|
return ret;
|
}
|
|
ret = fecmxc_initialize(bis);
|
if (ret) {
|
printf("FEC MXS: Unable to init FEC\n");
|
return ret;
|
}
|
|
dev = eth_get_dev_by_name("FEC");
|
if (!dev) {
|
printf("FEC MXS: Unable to get FEC device entry\n");
|
return -EINVAL;
|
}
|
|
ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
|
if (ret) {
|
printf("FEC MXS: Unable to register FEC MII postcall\n");
|
return ret;
|
}
|
|
return ret;
|
}
|
#endif
|
|
#ifdef CONFIG_SERIAL_TAG
|
#define MXS_OCOTP_MAX_TIMEOUT 1000000
|
void get_board_serial(struct tag_serialnr *serialnr)
|
{
|
struct mxs_ocotp_regs *ocotp_regs =
|
(struct mxs_ocotp_regs *)MXS_OCOTP_BASE;
|
|
serialnr->high = 0;
|
serialnr->low = 0;
|
|
writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
|
|
if (mxs_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
|
MXS_OCOTP_MAX_TIMEOUT)) {
|
printf("MXS: Can't get serial number from OCOTP\n");
|
return;
|
}
|
|
serialnr->low = readl(&ocotp_regs->hw_ocotp_cust3);
|
}
|
#endif
|
|
#ifdef CONFIG_REVISION_TAG
|
u32 get_board_rev(void)
|
{
|
if (env_get("revision#") != NULL)
|
return simple_strtoul(env_get("revision#"), NULL, 10);
|
return 0;
|
}
|
#endif
|
