// SPDX-License-Identifier: GPL-2.0-only
|
/* Linux driver for devices based on the DiBcom DiB0700 USB bridge
|
*
|
* Copyright (C) 2005-9 DiBcom, SA et al
|
*/
|
#include "dib0700.h"
|
|
#include "dib3000mc.h"
|
#include "dib7000m.h"
|
#include "dib7000p.h"
|
#include "dib8000.h"
|
#include "dib9000.h"
|
#include "mt2060.h"
|
#include "mt2266.h"
|
#include "tuner-xc2028.h"
|
#include "xc5000.h"
|
#include "xc4000.h"
|
#include "s5h1411.h"
|
#include "dib0070.h"
|
#include "dib0090.h"
|
#include "lgdt3305.h"
|
#include "mxl5007t.h"
|
#include "mn88472.h"
|
#include "tda18250.h"
|
|
|
static int force_lna_activation;
|
module_param(force_lna_activation, int, 0644);
|
MODULE_PARM_DESC(force_lna_activation, "force the activation of Low-Noise-Amplifier(s) (LNA), if applicable for the device (default: 0=automatic/off).");
|
|
struct dib0700_adapter_state {
|
int (*set_param_save) (struct dvb_frontend *);
|
const struct firmware *frontend_firmware;
|
struct dib7000p_ops dib7000p_ops;
|
struct dib8000_ops dib8000_ops;
|
};
|
|
/* Hauppauge Nova-T 500 (aka Bristol)
|
* has a LNA on GPIO0 which is enabled by setting 1 */
|
static struct mt2060_config bristol_mt2060_config[2] = {
|
{
|
.i2c_address = 0x60,
|
.clock_out = 3,
|
}, {
|
.i2c_address = 0x61,
|
}
|
};
|
|
|
static struct dibx000_agc_config bristol_dib3000p_mt2060_agc_config = {
|
.band_caps = BAND_VHF | BAND_UHF,
|
.setup = (1 << 8) | (5 << 5) | (0 << 4) | (0 << 3) | (0 << 2) | (2 << 0),
|
|
.agc1_max = 42598,
|
.agc1_min = 17694,
|
.agc2_max = 45875,
|
.agc2_min = 0,
|
|
.agc1_pt1 = 0,
|
.agc1_pt2 = 59,
|
|
.agc1_slope1 = 0,
|
.agc1_slope2 = 69,
|
|
.agc2_pt1 = 0,
|
.agc2_pt2 = 59,
|
|
.agc2_slope1 = 111,
|
.agc2_slope2 = 28,
|
};
|
|
static struct dib3000mc_config bristol_dib3000mc_config[2] = {
|
{ .agc = &bristol_dib3000p_mt2060_agc_config,
|
.max_time = 0x196,
|
.ln_adc_level = 0x1cc7,
|
.output_mpeg2_in_188_bytes = 1,
|
},
|
{ .agc = &bristol_dib3000p_mt2060_agc_config,
|
.max_time = 0x196,
|
.ln_adc_level = 0x1cc7,
|
.output_mpeg2_in_188_bytes = 1,
|
}
|
};
|
|
static int bristol_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_state *st = adap->dev->priv;
|
if (adap->id == 0) {
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0); msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1); msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0); msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1); msleep(10);
|
|
if (force_lna_activation)
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
else
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 0);
|
|
if (dib3000mc_i2c_enumeration(&adap->dev->i2c_adap, 2, DEFAULT_DIB3000P_I2C_ADDRESS, bristol_dib3000mc_config) != 0) {
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0); msleep(10);
|
return -ENODEV;
|
}
|
}
|
st->mt2060_if1[adap->id] = 1220;
|
return (adap->fe_adap[0].fe = dvb_attach(dib3000mc_attach, &adap->dev->i2c_adap,
|
(10 + adap->id) << 1, &bristol_dib3000mc_config[adap->id])) == NULL ? -ENODEV : 0;
|
}
|
|
static int eeprom_read(struct i2c_adapter *adap,u8 adrs,u8 *pval)
|
{
|
struct i2c_msg msg[2] = {
|
{ .addr = 0x50, .flags = 0, .buf = &adrs, .len = 1 },
|
{ .addr = 0x50, .flags = I2C_M_RD, .buf = pval, .len = 1 },
|
};
|
if (i2c_transfer(adap, msg, 2) != 2) return -EREMOTEIO;
|
return 0;
|
}
|
|
static int bristol_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct i2c_adapter *prim_i2c = &adap->dev->i2c_adap;
|
struct i2c_adapter *tun_i2c = dib3000mc_get_tuner_i2c_master(adap->fe_adap[0].fe, 1);
|
s8 a;
|
int if1=1220;
|
if (adap->dev->udev->descriptor.idVendor == cpu_to_le16(USB_VID_HAUPPAUGE) &&
|
adap->dev->udev->descriptor.idProduct == cpu_to_le16(USB_PID_HAUPPAUGE_NOVA_T_500_2)) {
|
if (!eeprom_read(prim_i2c,0x59 + adap->id,&a)) if1=1220+a;
|
}
|
return dvb_attach(mt2060_attach, adap->fe_adap[0].fe, tun_i2c,
|
&bristol_mt2060_config[adap->id], if1) == NULL ?
|
-ENODEV : 0;
|
}
|
|
/* STK7700D: Pinnacle/Terratec/Hauppauge Dual DVB-T Diversity */
|
|
/* MT226x */
|
static struct dibx000_agc_config stk7700d_7000p_mt2266_agc_config[2] = {
|
{
|
BAND_UHF,
|
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=1, P_agc_inv_pwm1=1, P_agc_inv_pwm2=1,
|
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=2, P_agc_write=0 */
|
(0 << 15) | (0 << 14) | (1 << 11) | (1 << 10) | (1 << 9) | (0 << 8)
|
| (3 << 5) | (0 << 4) | (5 << 1) | (0 << 0),
|
|
1130,
|
21,
|
|
0,
|
118,
|
|
0,
|
3530,
|
1,
|
0,
|
|
65535,
|
33770,
|
65535,
|
23592,
|
|
0,
|
62,
|
255,
|
64,
|
64,
|
132,
|
192,
|
80,
|
80,
|
|
17,
|
27,
|
23,
|
51,
|
|
1,
|
}, {
|
BAND_VHF | BAND_LBAND,
|
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=1, P_agc_inv_pwm1=1, P_agc_inv_pwm2=1,
|
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=2, P_agc_write=0 */
|
(0 << 15) | (0 << 14) | (1 << 11) | (1 << 10) | (1 << 9) | (0 << 8)
|
| (3 << 5) | (0 << 4) | (2 << 1) | (0 << 0),
|
|
2372,
|
21,
|
|
0,
|
118,
|
|
0,
|
3530,
|
1,
|
0,
|
|
65535,
|
0,
|
65535,
|
23592,
|
|
0,
|
128,
|
128,
|
128,
|
0,
|
128,
|
253,
|
81,
|
0,
|
|
17,
|
27,
|
23,
|
51,
|
|
1,
|
}
|
};
|
|
static struct dibx000_bandwidth_config stk7700d_mt2266_pll_config = {
|
.internal = 60000,
|
.sampling = 30000,
|
.pll_prediv = 1,
|
.pll_ratio = 8,
|
.pll_range = 3,
|
.pll_reset = 1,
|
.pll_bypass = 0,
|
.enable_refdiv = 0,
|
.bypclk_div = 0,
|
.IO_CLK_en_core = 1,
|
.ADClkSrc = 1,
|
.modulo = 2,
|
.sad_cfg = (3 << 14) | (1 << 12) | (524 << 0),
|
.ifreq = 0,
|
.timf = 20452225,
|
};
|
|
static struct dib7000p_config stk7700d_dib7000p_mt2266_config[] = {
|
{ .output_mpeg2_in_188_bytes = 1,
|
.hostbus_diversity = 1,
|
.tuner_is_baseband = 1,
|
|
.agc_config_count = 2,
|
.agc = stk7700d_7000p_mt2266_agc_config,
|
.bw = &stk7700d_mt2266_pll_config,
|
|
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
|
},
|
{ .output_mpeg2_in_188_bytes = 1,
|
.hostbus_diversity = 1,
|
.tuner_is_baseband = 1,
|
|
.agc_config_count = 2,
|
.agc = stk7700d_7000p_mt2266_agc_config,
|
.bw = &stk7700d_mt2266_pll_config,
|
|
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
|
}
|
};
|
|
static struct mt2266_config stk7700d_mt2266_config[2] = {
|
{ .i2c_address = 0x60
|
},
|
{ .i2c_address = 0x60
|
}
|
};
|
|
static int stk7700P2_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
if (adap->id == 0) {
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(10);
|
if (state->dib7000p_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 18,
|
stk7700d_dib7000p_mt2266_config)
|
!= 0) {
|
err("%s: state->dib7000p_ops.i2c_enumeration failed. Cannot continue\n", __func__);
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
}
|
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap,
|
0x80 + (adap->id << 1),
|
&stk7700d_dib7000p_mt2266_config[adap->id]);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int stk7700d_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
if (adap->id == 0) {
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
if (state->dib7000p_ops.i2c_enumeration(&adap->dev->i2c_adap, 2, 18,
|
stk7700d_dib7000p_mt2266_config)
|
!= 0) {
|
err("%s: state->dib7000p_ops.i2c_enumeration failed. Cannot continue\n", __func__);
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
}
|
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap,
|
0x80 + (adap->id << 1),
|
&stk7700d_dib7000p_mt2266_config[adap->id]);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int stk7700d_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct i2c_adapter *tun_i2c;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
tun_i2c = state->dib7000p_ops.get_i2c_master(adap->fe_adap[0].fe,
|
DIBX000_I2C_INTERFACE_TUNER, 1);
|
return dvb_attach(mt2266_attach, adap->fe_adap[0].fe, tun_i2c,
|
&stk7700d_mt2266_config[adap->id]) == NULL ? -ENODEV : 0;
|
}
|
|
/* STK7700-PH: Digital/Analog Hybrid Tuner, e.h. Cinergy HT USB HE */
|
static struct dibx000_agc_config xc3028_agc_config = {
|
.band_caps = BAND_VHF | BAND_UHF,
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=0,
|
* P_agc_inv_pwm1=0, P_agc_inv_pwm2=0, P_agc_inh_dc_rv_est=0,
|
* P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=2, P_agc_write=0 */
|
.setup = (0 << 15) | (0 << 14) | (0 << 11) | (0 << 10) | (0 << 9) | (0 << 8) | (3 << 5) | (0 << 4) | (2 << 1) | (0 << 0),
|
.inv_gain = 712,
|
.time_stabiliz = 21,
|
.alpha_level = 0,
|
.thlock = 118,
|
.wbd_inv = 0,
|
.wbd_ref = 2867,
|
.wbd_sel = 0,
|
.wbd_alpha = 2,
|
.agc1_max = 0,
|
.agc1_min = 0,
|
.agc2_max = 39718,
|
.agc2_min = 9930,
|
.agc1_pt1 = 0,
|
.agc1_pt2 = 0,
|
.agc1_pt3 = 0,
|
.agc1_slope1 = 0,
|
.agc1_slope2 = 0,
|
.agc2_pt1 = 0,
|
.agc2_pt2 = 128,
|
.agc2_slope1 = 29,
|
.agc2_slope2 = 29,
|
.alpha_mant = 17,
|
.alpha_exp = 27,
|
.beta_mant = 23,
|
.beta_exp = 51,
|
.perform_agc_softsplit = 1,
|
};
|
|
/* PLL Configuration for COFDM BW_MHz = 8.00 with external clock = 30.00 */
|
static struct dibx000_bandwidth_config xc3028_bw_config = {
|
.internal = 60000,
|
.sampling = 30000,
|
.pll_prediv = 1,
|
.pll_ratio = 8,
|
.pll_range = 3,
|
.pll_reset = 1,
|
.pll_bypass = 0,
|
.enable_refdiv = 0,
|
.bypclk_div = 0,
|
.IO_CLK_en_core = 1,
|
.ADClkSrc = 1,
|
.modulo = 0,
|
.sad_cfg = (3 << 14) | (1 << 12) | (524 << 0), /* sad_cfg: refsel, sel, freq_15k */
|
.ifreq = (1 << 25) | 5816102, /* ifreq = 5.200000 MHz */
|
.timf = 20452225,
|
.xtal_hz = 30000000,
|
};
|
|
static struct dib7000p_config stk7700ph_dib7700_xc3028_config = {
|
.output_mpeg2_in_188_bytes = 1,
|
.tuner_is_baseband = 1,
|
|
.agc_config_count = 1,
|
.agc = &xc3028_agc_config,
|
.bw = &xc3028_bw_config,
|
|
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
|
};
|
|
static int stk7700ph_xc3028_callback(void *ptr, int component,
|
int command, int arg)
|
{
|
struct dvb_usb_adapter *adap = ptr;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
switch (command) {
|
case XC2028_TUNER_RESET:
|
/* Send the tuner in then out of reset */
|
state->dib7000p_ops.set_gpio(adap->fe_adap[0].fe, 8, 0, 0);
|
msleep(10);
|
state->dib7000p_ops.set_gpio(adap->fe_adap[0].fe, 8, 0, 1);
|
break;
|
case XC2028_RESET_CLK:
|
case XC2028_I2C_FLUSH:
|
break;
|
default:
|
err("%s: unknown command %d, arg %d\n", __func__,
|
command, arg);
|
return -EINVAL;
|
}
|
return 0;
|
}
|
|
static struct xc2028_ctrl stk7700ph_xc3028_ctrl = {
|
.fname = XC2028_DEFAULT_FIRMWARE,
|
.max_len = 64,
|
.demod = XC3028_FE_DIBCOM52,
|
};
|
|
static struct xc2028_config stk7700ph_xc3028_config = {
|
.i2c_addr = 0x61,
|
.ctrl = &stk7700ph_xc3028_ctrl,
|
};
|
|
static int stk7700ph_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct usb_device_descriptor *desc = &adap->dev->udev->descriptor;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
if (desc->idVendor == cpu_to_le16(USB_VID_PINNACLE) &&
|
desc->idProduct == cpu_to_le16(USB_PID_PINNACLE_EXPRESSCARD_320CX))
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0);
|
else
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
msleep(10);
|
|
if (state->dib7000p_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 18,
|
&stk7700ph_dib7700_xc3028_config) != 0) {
|
err("%s: state->dib7000p_ops.i2c_enumeration failed. Cannot continue\n",
|
__func__);
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap, 0x80,
|
&stk7700ph_dib7700_xc3028_config);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int stk7700ph_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct i2c_adapter *tun_i2c;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
tun_i2c = state->dib7000p_ops.get_i2c_master(adap->fe_adap[0].fe,
|
DIBX000_I2C_INTERFACE_TUNER, 1);
|
|
stk7700ph_xc3028_config.i2c_adap = tun_i2c;
|
|
/* FIXME: generalize & move to common area */
|
adap->fe_adap[0].fe->callback = stk7700ph_xc3028_callback;
|
|
return dvb_attach(xc2028_attach, adap->fe_adap[0].fe, &stk7700ph_xc3028_config)
|
== NULL ? -ENODEV : 0;
|
}
|
|
#define DEFAULT_RC_INTERVAL 50
|
|
/*
|
* This function is used only when firmware is < 1.20 version. Newer
|
* firmwares use bulk mode, with functions implemented at dib0700_core,
|
* at dib0700_rc_urb_completion()
|
*/
|
static int dib0700_rc_query_old_firmware(struct dvb_usb_device *d)
|
{
|
enum rc_proto protocol;
|
u32 scancode;
|
u8 toggle;
|
int i;
|
struct dib0700_state *st = d->priv;
|
|
if (st->fw_version >= 0x10200) {
|
/* For 1.20 firmware , We need to keep the RC polling
|
callback so we can reuse the input device setup in
|
dvb-usb-remote.c. However, the actual work is being done
|
in the bulk URB completion handler. */
|
return 0;
|
}
|
|
st->buf[0] = REQUEST_POLL_RC;
|
st->buf[1] = 0;
|
|
i = dib0700_ctrl_rd(d, st->buf, 2, st->buf, 4);
|
if (i <= 0) {
|
err("RC Query Failed");
|
return -EIO;
|
}
|
|
/* losing half of KEY_0 events from Philipps rc5 remotes.. */
|
if (st->buf[0] == 0 && st->buf[1] == 0
|
&& st->buf[2] == 0 && st->buf[3] == 0)
|
return 0;
|
|
/* info("%d: %2X %2X %2X %2X",dvb_usb_dib0700_ir_proto,(int)st->buf[3 - 2],(int)st->buf[3 - 3],(int)st->buf[3 - 1],(int)st->buf[3]); */
|
|
dib0700_rc_setup(d, NULL); /* reset ir sensor data to prevent false events */
|
|
switch (d->props.rc.core.protocol) {
|
case RC_PROTO_BIT_NEC:
|
/* NEC protocol sends repeat code as 0 0 0 FF */
|
if ((st->buf[3 - 2] == 0x00) && (st->buf[3 - 3] == 0x00) &&
|
(st->buf[3] == 0xff)) {
|
rc_repeat(d->rc_dev);
|
return 0;
|
}
|
|
protocol = RC_PROTO_NEC;
|
scancode = RC_SCANCODE_NEC(st->buf[3 - 2], st->buf[3 - 3]);
|
toggle = 0;
|
break;
|
|
default:
|
/* RC-5 protocol changes toggle bit on new keypress */
|
protocol = RC_PROTO_RC5;
|
scancode = RC_SCANCODE_RC5(st->buf[3 - 2], st->buf[3 - 3]);
|
toggle = st->buf[3 - 1];
|
break;
|
}
|
|
rc_keydown(d->rc_dev, protocol, scancode, toggle);
|
return 0;
|
}
|
|
/* STK7700P: Hauppauge Nova-T Stick, AVerMedia Volar */
|
static struct dibx000_agc_config stk7700p_7000m_mt2060_agc_config = {
|
BAND_UHF | BAND_VHF,
|
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=5, P_agc_inv_pwm1=0, P_agc_inv_pwm2=0,
|
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=2, P_agc_write=0 */
|
(0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) | (0 << 8)
|
| (3 << 5) | (0 << 4) | (2 << 1) | (0 << 0),
|
|
712,
|
41,
|
|
0,
|
118,
|
|
0,
|
4095,
|
0,
|
0,
|
|
42598,
|
17694,
|
45875,
|
2621,
|
0,
|
76,
|
139,
|
52,
|
59,
|
107,
|
172,
|
57,
|
70,
|
|
21,
|
25,
|
28,
|
48,
|
|
1,
|
{ 0,
|
107,
|
51800,
|
24700
|
},
|
};
|
|
static struct dibx000_agc_config stk7700p_7000p_mt2060_agc_config = {
|
.band_caps = BAND_UHF | BAND_VHF,
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=5, P_agc_inv_pwm1=0, P_agc_inv_pwm2=0,
|
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=2, P_agc_write=0 */
|
.setup = (0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) | (0 << 8) | (3 << 5) | (0 << 4) | (2 << 1) | (0 << 0),
|
.inv_gain = 712,
|
.time_stabiliz = 41,
|
.alpha_level = 0,
|
.thlock = 118,
|
.wbd_inv = 0,
|
.wbd_ref = 4095,
|
.wbd_sel = 0,
|
.wbd_alpha = 0,
|
.agc1_max = 42598,
|
.agc1_min = 16384,
|
.agc2_max = 42598,
|
.agc2_min = 0,
|
.agc1_pt1 = 0,
|
.agc1_pt2 = 137,
|
.agc1_pt3 = 255,
|
.agc1_slope1 = 0,
|
.agc1_slope2 = 255,
|
.agc2_pt1 = 0,
|
.agc2_pt2 = 0,
|
.agc2_slope1 = 0,
|
.agc2_slope2 = 41,
|
.alpha_mant = 15,
|
.alpha_exp = 25,
|
.beta_mant = 28,
|
.beta_exp = 48,
|
.perform_agc_softsplit = 0,
|
};
|
|
static struct dibx000_bandwidth_config stk7700p_pll_config = {
|
.internal = 60000,
|
.sampling = 30000,
|
.pll_prediv = 1,
|
.pll_ratio = 8,
|
.pll_range = 3,
|
.pll_reset = 1,
|
.pll_bypass = 0,
|
.enable_refdiv = 0,
|
.bypclk_div = 0,
|
.IO_CLK_en_core = 1,
|
.ADClkSrc = 1,
|
.modulo = 0,
|
.sad_cfg = (3 << 14) | (1 << 12) | (524 << 0),
|
.ifreq = 60258167,
|
.timf = 20452225,
|
.xtal_hz = 30000000,
|
};
|
|
static struct dib7000m_config stk7700p_dib7000m_config = {
|
.dvbt_mode = 1,
|
.output_mpeg2_in_188_bytes = 1,
|
.quartz_direct = 1,
|
|
.agc_config_count = 1,
|
.agc = &stk7700p_7000m_mt2060_agc_config,
|
.bw = &stk7700p_pll_config,
|
|
.gpio_dir = DIB7000M_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000M_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000M_GPIO_DEFAULT_PWM_POS,
|
};
|
|
static struct dib7000p_config stk7700p_dib7000p_config = {
|
.output_mpeg2_in_188_bytes = 1,
|
|
.agc_config_count = 1,
|
.agc = &stk7700p_7000p_mt2060_agc_config,
|
.bw = &stk7700p_pll_config,
|
|
.gpio_dir = DIB7000M_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000M_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000M_GPIO_DEFAULT_PWM_POS,
|
};
|
|
static int stk7700p_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_state *st = adap->dev->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
/* unless there is no real power management in DVB - we leave the device on GPIO6 */
|
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0); msleep(50);
|
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1); msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0); msleep(10);
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1); msleep(100);
|
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
st->mt2060_if1[0] = 1220;
|
|
if (state->dib7000p_ops.dib7000pc_detection(&adap->dev->i2c_adap)) {
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap, 18, &stk7700p_dib7000p_config);
|
st->is_dib7000pc = 1;
|
} else {
|
memset(&state->dib7000p_ops, 0, sizeof(state->dib7000p_ops));
|
adap->fe_adap[0].fe = dvb_attach(dib7000m_attach, &adap->dev->i2c_adap, 18, &stk7700p_dib7000m_config);
|
}
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static struct mt2060_config stk7700p_mt2060_config = {
|
0x60
|
};
|
|
static int stk7700p_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct i2c_adapter *prim_i2c = &adap->dev->i2c_adap;
|
struct dib0700_state *st = adap->dev->priv;
|
struct i2c_adapter *tun_i2c;
|
struct dib0700_adapter_state *state = adap->priv;
|
s8 a;
|
int if1=1220;
|
|
if (adap->dev->udev->descriptor.idVendor == cpu_to_le16(USB_VID_HAUPPAUGE) &&
|
adap->dev->udev->descriptor.idProduct == cpu_to_le16(USB_PID_HAUPPAUGE_NOVA_T_STICK)) {
|
if (!eeprom_read(prim_i2c,0x58,&a)) if1=1220+a;
|
}
|
if (st->is_dib7000pc)
|
tun_i2c = state->dib7000p_ops.get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_TUNER, 1);
|
else
|
tun_i2c = dib7000m_get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_TUNER, 1);
|
|
return dvb_attach(mt2060_attach, adap->fe_adap[0].fe, tun_i2c, &stk7700p_mt2060_config,
|
if1) == NULL ? -ENODEV : 0;
|
}
|
|
/* DIB7070 generic */
|
static struct dibx000_agc_config dib7070_agc_config = {
|
.band_caps = BAND_UHF | BAND_VHF | BAND_LBAND | BAND_SBAND,
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=5, P_agc_inv_pwm1=0, P_agc_inv_pwm2=0,
|
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=5, P_agc_write=0 */
|
.setup = (0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) | (0 << 8) | (3 << 5) | (0 << 4) | (5 << 1) | (0 << 0),
|
.inv_gain = 600,
|
.time_stabiliz = 10,
|
.alpha_level = 0,
|
.thlock = 118,
|
.wbd_inv = 0,
|
.wbd_ref = 3530,
|
.wbd_sel = 1,
|
.wbd_alpha = 5,
|
.agc1_max = 65535,
|
.agc1_min = 0,
|
.agc2_max = 65535,
|
.agc2_min = 0,
|
.agc1_pt1 = 0,
|
.agc1_pt2 = 40,
|
.agc1_pt3 = 183,
|
.agc1_slope1 = 206,
|
.agc1_slope2 = 255,
|
.agc2_pt1 = 72,
|
.agc2_pt2 = 152,
|
.agc2_slope1 = 88,
|
.agc2_slope2 = 90,
|
.alpha_mant = 17,
|
.alpha_exp = 27,
|
.beta_mant = 23,
|
.beta_exp = 51,
|
.perform_agc_softsplit = 0,
|
};
|
|
static int dib7070_tuner_reset(struct dvb_frontend *fe, int onoff)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
deb_info("reset: %d", onoff);
|
return state->dib7000p_ops.set_gpio(fe, 8, 0, !onoff);
|
}
|
|
static int dib7070_tuner_sleep(struct dvb_frontend *fe, int onoff)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
deb_info("sleep: %d", onoff);
|
return state->dib7000p_ops.set_gpio(fe, 9, 0, onoff);
|
}
|
|
static struct dib0070_config dib7070p_dib0070_config[2] = {
|
{
|
.i2c_address = DEFAULT_DIB0070_I2C_ADDRESS,
|
.reset = dib7070_tuner_reset,
|
.sleep = dib7070_tuner_sleep,
|
.clock_khz = 12000,
|
.clock_pad_drive = 4,
|
.charge_pump = 2,
|
}, {
|
.i2c_address = DEFAULT_DIB0070_I2C_ADDRESS,
|
.reset = dib7070_tuner_reset,
|
.sleep = dib7070_tuner_sleep,
|
.clock_khz = 12000,
|
.charge_pump = 2,
|
}
|
};
|
|
static struct dib0070_config dib7770p_dib0070_config = {
|
.i2c_address = DEFAULT_DIB0070_I2C_ADDRESS,
|
.reset = dib7070_tuner_reset,
|
.sleep = dib7070_tuner_sleep,
|
.clock_khz = 12000,
|
.clock_pad_drive = 0,
|
.flip_chip = 1,
|
.charge_pump = 2,
|
};
|
|
static int dib7070_set_param_override(struct dvb_frontend *fe)
|
{
|
struct dtv_frontend_properties *p = &fe->dtv_property_cache;
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
u16 offset;
|
u8 band = BAND_OF_FREQUENCY(p->frequency/1000);
|
switch (band) {
|
case BAND_VHF: offset = 950; break;
|
case BAND_UHF:
|
default: offset = 550; break;
|
}
|
deb_info("WBD for DiB7000P: %d\n", offset + dib0070_wbd_offset(fe));
|
state->dib7000p_ops.set_wbd_ref(fe, offset + dib0070_wbd_offset(fe));
|
return state->set_param_save(fe);
|
}
|
|
static int dib7770_set_param_override(struct dvb_frontend *fe)
|
{
|
struct dtv_frontend_properties *p = &fe->dtv_property_cache;
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
u16 offset;
|
u8 band = BAND_OF_FREQUENCY(p->frequency/1000);
|
switch (band) {
|
case BAND_VHF:
|
state->dib7000p_ops.set_gpio(fe, 0, 0, 1);
|
offset = 850;
|
break;
|
case BAND_UHF:
|
default:
|
state->dib7000p_ops.set_gpio(fe, 0, 0, 0);
|
offset = 250;
|
break;
|
}
|
deb_info("WBD for DiB7000P: %d\n", offset + dib0070_wbd_offset(fe));
|
state->dib7000p_ops.set_wbd_ref(fe, offset + dib0070_wbd_offset(fe));
|
return state->set_param_save(fe);
|
}
|
|
static int dib7770p_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *st = adap->priv;
|
struct i2c_adapter *tun_i2c = st->dib7000p_ops.get_i2c_master(adap->fe_adap[0].fe,
|
DIBX000_I2C_INTERFACE_TUNER, 1);
|
|
if (dvb_attach(dib0070_attach, adap->fe_adap[0].fe, tun_i2c,
|
&dib7770p_dib0070_config) == NULL)
|
return -ENODEV;
|
|
st->set_param_save = adap->fe_adap[0].fe->ops.tuner_ops.set_params;
|
adap->fe_adap[0].fe->ops.tuner_ops.set_params = dib7770_set_param_override;
|
return 0;
|
}
|
|
static int dib7070p_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *st = adap->priv;
|
struct i2c_adapter *tun_i2c = st->dib7000p_ops.get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_TUNER, 1);
|
|
if (adap->id == 0) {
|
if (dvb_attach(dib0070_attach, adap->fe_adap[0].fe, tun_i2c, &dib7070p_dib0070_config[0]) == NULL)
|
return -ENODEV;
|
} else {
|
if (dvb_attach(dib0070_attach, adap->fe_adap[0].fe, tun_i2c, &dib7070p_dib0070_config[1]) == NULL)
|
return -ENODEV;
|
}
|
|
st->set_param_save = adap->fe_adap[0].fe->ops.tuner_ops.set_params;
|
adap->fe_adap[0].fe->ops.tuner_ops.set_params = dib7070_set_param_override;
|
return 0;
|
}
|
|
static int stk7700p_pid_filter(struct dvb_usb_adapter *adapter, int index,
|
u16 pid, int onoff)
|
{
|
struct dib0700_adapter_state *state = adapter->priv;
|
struct dib0700_state *st = adapter->dev->priv;
|
|
if (st->is_dib7000pc)
|
return state->dib7000p_ops.pid_filter(adapter->fe_adap[0].fe, index, pid, onoff);
|
return dib7000m_pid_filter(adapter->fe_adap[0].fe, index, pid, onoff);
|
}
|
|
static int stk7700p_pid_filter_ctrl(struct dvb_usb_adapter *adapter, int onoff)
|
{
|
struct dib0700_state *st = adapter->dev->priv;
|
struct dib0700_adapter_state *state = adapter->priv;
|
if (st->is_dib7000pc)
|
return state->dib7000p_ops.pid_filter_ctrl(adapter->fe_adap[0].fe, onoff);
|
return dib7000m_pid_filter_ctrl(adapter->fe_adap[0].fe, onoff);
|
}
|
|
static int stk70x0p_pid_filter(struct dvb_usb_adapter *adapter, int index, u16 pid, int onoff)
|
{
|
struct dib0700_adapter_state *state = adapter->priv;
|
return state->dib7000p_ops.pid_filter(adapter->fe_adap[0].fe, index, pid, onoff);
|
}
|
|
static int stk70x0p_pid_filter_ctrl(struct dvb_usb_adapter *adapter, int onoff)
|
{
|
struct dib0700_adapter_state *state = adapter->priv;
|
return state->dib7000p_ops.pid_filter_ctrl(adapter->fe_adap[0].fe, onoff);
|
}
|
|
static struct dibx000_bandwidth_config dib7070_bw_config_12_mhz = {
|
.internal = 60000,
|
.sampling = 15000,
|
.pll_prediv = 1,
|
.pll_ratio = 20,
|
.pll_range = 3,
|
.pll_reset = 1,
|
.pll_bypass = 0,
|
.enable_refdiv = 0,
|
.bypclk_div = 0,
|
.IO_CLK_en_core = 1,
|
.ADClkSrc = 1,
|
.modulo = 2,
|
.sad_cfg = (3 << 14) | (1 << 12) | (524 << 0),
|
.ifreq = (0 << 25) | 0,
|
.timf = 20452225,
|
.xtal_hz = 12000000,
|
};
|
|
static struct dib7000p_config dib7070p_dib7000p_config = {
|
.output_mpeg2_in_188_bytes = 1,
|
|
.agc_config_count = 1,
|
.agc = &dib7070_agc_config,
|
.bw = &dib7070_bw_config_12_mhz,
|
.tuner_is_baseband = 1,
|
.spur_protect = 1,
|
|
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
|
|
.hostbus_diversity = 1,
|
};
|
|
/* STK7070P */
|
static int stk7070p_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct usb_device_descriptor *p = &adap->dev->udev->descriptor;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
if (p->idVendor == cpu_to_le16(USB_VID_PINNACLE) &&
|
p->idProduct == cpu_to_le16(USB_PID_PINNACLE_PCTV72E))
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0);
|
else
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
if (state->dib7000p_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 18,
|
&dib7070p_dib7000p_config) != 0) {
|
err("%s: state->dib7000p_ops.i2c_enumeration failed. Cannot continue\n",
|
__func__);
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap, 0x80,
|
&dib7070p_dib7000p_config);
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
/* STK7770P */
|
static struct dib7000p_config dib7770p_dib7000p_config = {
|
.output_mpeg2_in_188_bytes = 1,
|
|
.agc_config_count = 1,
|
.agc = &dib7070_agc_config,
|
.bw = &dib7070_bw_config_12_mhz,
|
.tuner_is_baseband = 1,
|
.spur_protect = 1,
|
|
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
|
|
.hostbus_diversity = 1,
|
.enable_current_mirror = 1,
|
.disable_sample_and_hold = 0,
|
};
|
|
static int stk7770p_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct usb_device_descriptor *p = &adap->dev->udev->descriptor;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
if (p->idVendor == cpu_to_le16(USB_VID_PINNACLE) &&
|
p->idProduct == cpu_to_le16(USB_PID_PINNACLE_PCTV72E))
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0);
|
else
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
if (state->dib7000p_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 18,
|
&dib7770p_dib7000p_config) != 0) {
|
err("%s: state->dib7000p_ops.i2c_enumeration failed. Cannot continue\n",
|
__func__);
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap, 0x80,
|
&dib7770p_dib7000p_config);
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
/* DIB807x generic */
|
static struct dibx000_agc_config dib807x_agc_config[2] = {
|
{
|
BAND_VHF,
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0,
|
* P_agc_freq_pwm_div=1, P_agc_inv_pwm1=0,
|
* P_agc_inv_pwm2=0,P_agc_inh_dc_rv_est=0,
|
* P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=5,
|
* P_agc_write=0 */
|
(0 << 15) | (0 << 14) | (7 << 11) | (0 << 10) | (0 << 9) |
|
(0 << 8) | (3 << 5) | (0 << 4) | (5 << 1) |
|
(0 << 0), /* setup*/
|
|
600, /* inv_gain*/
|
10, /* time_stabiliz*/
|
|
0, /* alpha_level*/
|
118, /* thlock*/
|
|
0, /* wbd_inv*/
|
3530, /* wbd_ref*/
|
1, /* wbd_sel*/
|
5, /* wbd_alpha*/
|
|
65535, /* agc1_max*/
|
0, /* agc1_min*/
|
|
65535, /* agc2_max*/
|
0, /* agc2_min*/
|
|
0, /* agc1_pt1*/
|
40, /* agc1_pt2*/
|
183, /* agc1_pt3*/
|
206, /* agc1_slope1*/
|
255, /* agc1_slope2*/
|
72, /* agc2_pt1*/
|
152, /* agc2_pt2*/
|
88, /* agc2_slope1*/
|
90, /* agc2_slope2*/
|
|
17, /* alpha_mant*/
|
27, /* alpha_exp*/
|
23, /* beta_mant*/
|
51, /* beta_exp*/
|
|
0, /* perform_agc_softsplit*/
|
}, {
|
BAND_UHF,
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0,
|
* P_agc_freq_pwm_div=1, P_agc_inv_pwm1=0,
|
* P_agc_inv_pwm2=0, P_agc_inh_dc_rv_est=0,
|
* P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=5,
|
* P_agc_write=0 */
|
(0 << 15) | (0 << 14) | (1 << 11) | (0 << 10) | (0 << 9) |
|
(0 << 8) | (3 << 5) | (0 << 4) | (5 << 1) |
|
(0 << 0), /* setup */
|
|
600, /* inv_gain*/
|
10, /* time_stabiliz*/
|
|
0, /* alpha_level*/
|
118, /* thlock*/
|
|
0, /* wbd_inv*/
|
3530, /* wbd_ref*/
|
1, /* wbd_sel*/
|
5, /* wbd_alpha*/
|
|
65535, /* agc1_max*/
|
0, /* agc1_min*/
|
|
65535, /* agc2_max*/
|
0, /* agc2_min*/
|
|
0, /* agc1_pt1*/
|
40, /* agc1_pt2*/
|
183, /* agc1_pt3*/
|
206, /* agc1_slope1*/
|
255, /* agc1_slope2*/
|
72, /* agc2_pt1*/
|
152, /* agc2_pt2*/
|
88, /* agc2_slope1*/
|
90, /* agc2_slope2*/
|
|
17, /* alpha_mant*/
|
27, /* alpha_exp*/
|
23, /* beta_mant*/
|
51, /* beta_exp*/
|
|
0, /* perform_agc_softsplit*/
|
}
|
};
|
|
static struct dibx000_bandwidth_config dib807x_bw_config_12_mhz = {
|
.internal = 60000,
|
.sampling = 15000,
|
.pll_prediv = 1,
|
.pll_ratio = 20,
|
.pll_range = 3,
|
.pll_reset = 1,
|
.pll_bypass = 0,
|
.enable_refdiv = 0,
|
.bypclk_div = 0,
|
.IO_CLK_en_core = 1,
|
.ADClkSrc = 1,
|
.modulo = 2,
|
.sad_cfg = (3 << 14) | (1 << 12) | (599 << 0), /* sad_cfg: refsel, sel, freq_15k*/
|
.ifreq = (0 << 25) | 0, /* ifreq = 0.000000 MHz*/
|
.timf = 18179755,
|
.xtal_hz = 12000000,
|
};
|
|
static struct dib8000_config dib807x_dib8000_config[2] = {
|
{
|
.output_mpeg2_in_188_bytes = 1,
|
|
.agc_config_count = 2,
|
.agc = dib807x_agc_config,
|
.pll = &dib807x_bw_config_12_mhz,
|
.tuner_is_baseband = 1,
|
|
.gpio_dir = DIB8000_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB8000_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB8000_GPIO_DEFAULT_PWM_POS,
|
|
.hostbus_diversity = 1,
|
.div_cfg = 1,
|
.agc_control = &dib0070_ctrl_agc_filter,
|
.output_mode = OUTMODE_MPEG2_FIFO,
|
.drives = 0x2d98,
|
}, {
|
.output_mpeg2_in_188_bytes = 1,
|
|
.agc_config_count = 2,
|
.agc = dib807x_agc_config,
|
.pll = &dib807x_bw_config_12_mhz,
|
.tuner_is_baseband = 1,
|
|
.gpio_dir = DIB8000_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB8000_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB8000_GPIO_DEFAULT_PWM_POS,
|
|
.hostbus_diversity = 1,
|
.agc_control = &dib0070_ctrl_agc_filter,
|
.output_mode = OUTMODE_MPEG2_FIFO,
|
.drives = 0x2d98,
|
}
|
};
|
|
static int dib80xx_tuner_reset(struct dvb_frontend *fe, int onoff)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
return state->dib8000_ops.set_gpio(fe, 5, 0, !onoff);
|
}
|
|
static int dib80xx_tuner_sleep(struct dvb_frontend *fe, int onoff)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
return state->dib8000_ops.set_gpio(fe, 0, 0, onoff);
|
}
|
|
static const struct dib0070_wbd_gain_cfg dib8070_wbd_gain_cfg[] = {
|
{ 240, 7},
|
{ 0xffff, 6},
|
};
|
|
static struct dib0070_config dib807x_dib0070_config[2] = {
|
{
|
.i2c_address = DEFAULT_DIB0070_I2C_ADDRESS,
|
.reset = dib80xx_tuner_reset,
|
.sleep = dib80xx_tuner_sleep,
|
.clock_khz = 12000,
|
.clock_pad_drive = 4,
|
.vga_filter = 1,
|
.force_crystal_mode = 1,
|
.enable_third_order_filter = 1,
|
.charge_pump = 0,
|
.wbd_gain = dib8070_wbd_gain_cfg,
|
.osc_buffer_state = 0,
|
.freq_offset_khz_uhf = -100,
|
.freq_offset_khz_vhf = -100,
|
}, {
|
.i2c_address = DEFAULT_DIB0070_I2C_ADDRESS,
|
.reset = dib80xx_tuner_reset,
|
.sleep = dib80xx_tuner_sleep,
|
.clock_khz = 12000,
|
.clock_pad_drive = 2,
|
.vga_filter = 1,
|
.force_crystal_mode = 1,
|
.enable_third_order_filter = 1,
|
.charge_pump = 0,
|
.wbd_gain = dib8070_wbd_gain_cfg,
|
.osc_buffer_state = 0,
|
.freq_offset_khz_uhf = -25,
|
.freq_offset_khz_vhf = -25,
|
}
|
};
|
|
static int dib807x_set_param_override(struct dvb_frontend *fe)
|
{
|
struct dtv_frontend_properties *p = &fe->dtv_property_cache;
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
u16 offset = dib0070_wbd_offset(fe);
|
u8 band = BAND_OF_FREQUENCY(p->frequency/1000);
|
switch (band) {
|
case BAND_VHF:
|
offset += 750;
|
break;
|
case BAND_UHF: /* fall-thru wanted */
|
default:
|
offset += 250; break;
|
}
|
deb_info("WBD for DiB8000: %d\n", offset);
|
state->dib8000_ops.set_wbd_ref(fe, offset);
|
|
return state->set_param_save(fe);
|
}
|
|
static int dib807x_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *st = adap->priv;
|
struct i2c_adapter *tun_i2c = st->dib8000_ops.get_i2c_master(adap->fe_adap[0].fe,
|
DIBX000_I2C_INTERFACE_TUNER, 1);
|
|
if (adap->id == 0) {
|
if (dvb_attach(dib0070_attach, adap->fe_adap[0].fe, tun_i2c,
|
&dib807x_dib0070_config[0]) == NULL)
|
return -ENODEV;
|
} else {
|
if (dvb_attach(dib0070_attach, adap->fe_adap[0].fe, tun_i2c,
|
&dib807x_dib0070_config[1]) == NULL)
|
return -ENODEV;
|
}
|
|
st->set_param_save = adap->fe_adap[0].fe->ops.tuner_ops.set_params;
|
adap->fe_adap[0].fe->ops.tuner_ops.set_params = dib807x_set_param_override;
|
return 0;
|
}
|
|
static int stk80xx_pid_filter(struct dvb_usb_adapter *adapter, int index,
|
u16 pid, int onoff)
|
{
|
struct dib0700_adapter_state *state = adapter->priv;
|
|
return state->dib8000_ops.pid_filter(adapter->fe_adap[0].fe, index, pid, onoff);
|
}
|
|
static int stk80xx_pid_filter_ctrl(struct dvb_usb_adapter *adapter,
|
int onoff)
|
{
|
struct dib0700_adapter_state *state = adapter->priv;
|
|
return state->dib8000_ops.pid_filter_ctrl(adapter->fe_adap[0].fe, onoff);
|
}
|
|
/* STK807x */
|
static int stk807x_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib8000_attach, &state->dib8000_ops))
|
return -ENODEV;
|
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
state->dib8000_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 18,
|
0x80, 0);
|
|
adap->fe_adap[0].fe = state->dib8000_ops.init(&adap->dev->i2c_adap, 0x80,
|
&dib807x_dib8000_config[0]);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
/* STK807xPVR */
|
static int stk807xpvr_frontend_attach0(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib8000_attach, &state->dib8000_ops))
|
return -ENODEV;
|
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0);
|
msleep(30);
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(500);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
/* initialize IC 0 */
|
state->dib8000_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 0x22, 0x80, 0);
|
|
adap->fe_adap[0].fe = state->dib8000_ops.init(&adap->dev->i2c_adap, 0x80,
|
&dib807x_dib8000_config[0]);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int stk807xpvr_frontend_attach1(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib8000_attach, &state->dib8000_ops))
|
return -ENODEV;
|
|
/* initialize IC 1 */
|
state->dib8000_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 0x12, 0x82, 0);
|
|
adap->fe_adap[0].fe = state->dib8000_ops.init(&adap->dev->i2c_adap, 0x82,
|
&dib807x_dib8000_config[1]);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
/* STK8096GP */
|
static struct dibx000_agc_config dib8090_agc_config[2] = {
|
{
|
.band_caps = BAND_UHF | BAND_VHF | BAND_LBAND | BAND_SBAND,
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=1,
|
* P_agc_inv_pwm1=0, P_agc_inv_pwm2=0, P_agc_inh_dc_rv_est=0,
|
* P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=5, P_agc_write=0 */
|
.setup = (0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) | (0 << 8)
|
| (3 << 5) | (0 << 4) | (5 << 1) | (0 << 0),
|
|
.inv_gain = 787,
|
.time_stabiliz = 10,
|
|
.alpha_level = 0,
|
.thlock = 118,
|
|
.wbd_inv = 0,
|
.wbd_ref = 3530,
|
.wbd_sel = 1,
|
.wbd_alpha = 5,
|
|
.agc1_max = 65535,
|
.agc1_min = 0,
|
|
.agc2_max = 65535,
|
.agc2_min = 0,
|
|
.agc1_pt1 = 0,
|
.agc1_pt2 = 32,
|
.agc1_pt3 = 114,
|
.agc1_slope1 = 143,
|
.agc1_slope2 = 144,
|
.agc2_pt1 = 114,
|
.agc2_pt2 = 227,
|
.agc2_slope1 = 116,
|
.agc2_slope2 = 117,
|
|
.alpha_mant = 28,
|
.alpha_exp = 26,
|
.beta_mant = 31,
|
.beta_exp = 51,
|
|
.perform_agc_softsplit = 0,
|
},
|
{
|
.band_caps = BAND_CBAND,
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=1,
|
* P_agc_inv_pwm1=0, P_agc_inv_pwm2=0, P_agc_inh_dc_rv_est=0,
|
* P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=5, P_agc_write=0 */
|
.setup = (0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) | (0 << 8)
|
| (3 << 5) | (0 << 4) | (5 << 1) | (0 << 0),
|
|
.inv_gain = 787,
|
.time_stabiliz = 10,
|
|
.alpha_level = 0,
|
.thlock = 118,
|
|
.wbd_inv = 0,
|
.wbd_ref = 3530,
|
.wbd_sel = 1,
|
.wbd_alpha = 5,
|
|
.agc1_max = 0,
|
.agc1_min = 0,
|
|
.agc2_max = 65535,
|
.agc2_min = 0,
|
|
.agc1_pt1 = 0,
|
.agc1_pt2 = 32,
|
.agc1_pt3 = 114,
|
.agc1_slope1 = 143,
|
.agc1_slope2 = 144,
|
.agc2_pt1 = 114,
|
.agc2_pt2 = 227,
|
.agc2_slope1 = 116,
|
.agc2_slope2 = 117,
|
|
.alpha_mant = 28,
|
.alpha_exp = 26,
|
.beta_mant = 31,
|
.beta_exp = 51,
|
|
.perform_agc_softsplit = 0,
|
}
|
};
|
|
static struct dibx000_bandwidth_config dib8090_pll_config_12mhz = {
|
.internal = 54000,
|
.sampling = 13500,
|
|
.pll_prediv = 1,
|
.pll_ratio = 18,
|
.pll_range = 3,
|
.pll_reset = 1,
|
.pll_bypass = 0,
|
|
.enable_refdiv = 0,
|
.bypclk_div = 0,
|
.IO_CLK_en_core = 1,
|
.ADClkSrc = 1,
|
.modulo = 2,
|
|
.sad_cfg = (3 << 14) | (1 << 12) | (599 << 0),
|
|
.ifreq = (0 << 25) | 0,
|
.timf = 20199727,
|
|
.xtal_hz = 12000000,
|
};
|
|
static int dib8090_get_adc_power(struct dvb_frontend *fe)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
return state->dib8000_ops.get_adc_power(fe, 1);
|
}
|
|
static void dib8090_agc_control(struct dvb_frontend *fe, u8 restart)
|
{
|
deb_info("AGC control callback: %i\n", restart);
|
dib0090_dcc_freq(fe, restart);
|
|
if (restart == 0) /* before AGC startup */
|
dib0090_set_dc_servo(fe, 1);
|
}
|
|
static struct dib8000_config dib809x_dib8000_config[2] = {
|
{
|
.output_mpeg2_in_188_bytes = 1,
|
|
.agc_config_count = 2,
|
.agc = dib8090_agc_config,
|
.agc_control = dib8090_agc_control,
|
.pll = &dib8090_pll_config_12mhz,
|
.tuner_is_baseband = 1,
|
|
.gpio_dir = DIB8000_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB8000_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB8000_GPIO_DEFAULT_PWM_POS,
|
|
.hostbus_diversity = 1,
|
.div_cfg = 0x31,
|
.output_mode = OUTMODE_MPEG2_FIFO,
|
.drives = 0x2d98,
|
.diversity_delay = 48,
|
.refclksel = 3,
|
}, {
|
.output_mpeg2_in_188_bytes = 1,
|
|
.agc_config_count = 2,
|
.agc = dib8090_agc_config,
|
.agc_control = dib8090_agc_control,
|
.pll = &dib8090_pll_config_12mhz,
|
.tuner_is_baseband = 1,
|
|
.gpio_dir = DIB8000_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB8000_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB8000_GPIO_DEFAULT_PWM_POS,
|
|
.hostbus_diversity = 1,
|
.div_cfg = 0x31,
|
.output_mode = OUTMODE_DIVERSITY,
|
.drives = 0x2d08,
|
.diversity_delay = 1,
|
.refclksel = 3,
|
}
|
};
|
|
static struct dib0090_wbd_slope dib8090_wbd_table[] = {
|
/* max freq ; cold slope ; cold offset ; warm slope ; warm offset ; wbd gain */
|
{ 120, 0, 500, 0, 500, 4 }, /* CBAND */
|
{ 170, 0, 450, 0, 450, 4 }, /* CBAND */
|
{ 380, 48, 373, 28, 259, 6 }, /* VHF */
|
{ 860, 34, 700, 36, 616, 6 }, /* high UHF */
|
{ 0xFFFF, 34, 700, 36, 616, 6 }, /* default */
|
};
|
|
static struct dib0090_config dib809x_dib0090_config = {
|
.io.pll_bypass = 1,
|
.io.pll_range = 1,
|
.io.pll_prediv = 1,
|
.io.pll_loopdiv = 20,
|
.io.adc_clock_ratio = 8,
|
.io.pll_int_loop_filt = 0,
|
.io.clock_khz = 12000,
|
.reset = dib80xx_tuner_reset,
|
.sleep = dib80xx_tuner_sleep,
|
.clkouttobamse = 1,
|
.analog_output = 1,
|
.i2c_address = DEFAULT_DIB0090_I2C_ADDRESS,
|
.use_pwm_agc = 1,
|
.clkoutdrive = 1,
|
.get_adc_power = dib8090_get_adc_power,
|
.freq_offset_khz_uhf = -63,
|
.freq_offset_khz_vhf = -143,
|
.wbd = dib8090_wbd_table,
|
.fref_clock_ratio = 6,
|
};
|
|
static u8 dib8090_compute_pll_parameters(struct dvb_frontend *fe)
|
{
|
u8 optimal_pll_ratio = 20;
|
u32 freq_adc, ratio, rest, max = 0;
|
u8 pll_ratio;
|
|
for (pll_ratio = 17; pll_ratio <= 20; pll_ratio++) {
|
freq_adc = 12 * pll_ratio * (1 << 8) / 16;
|
ratio = ((fe->dtv_property_cache.frequency / 1000) * (1 << 8) / 1000) / freq_adc;
|
rest = ((fe->dtv_property_cache.frequency / 1000) * (1 << 8) / 1000) - ratio * freq_adc;
|
|
if (rest > freq_adc / 2)
|
rest = freq_adc - rest;
|
deb_info("PLL ratio=%i rest=%i\n", pll_ratio, rest);
|
if ((rest > max) && (rest > 717)) {
|
optimal_pll_ratio = pll_ratio;
|
max = rest;
|
}
|
}
|
deb_info("optimal PLL ratio=%i\n", optimal_pll_ratio);
|
|
return optimal_pll_ratio;
|
}
|
|
static int dib8096_set_param_override(struct dvb_frontend *fe)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
u8 pll_ratio, band = BAND_OF_FREQUENCY(fe->dtv_property_cache.frequency / 1000);
|
u16 target, ltgain, rf_gain_limit;
|
u32 timf;
|
int ret = 0;
|
enum frontend_tune_state tune_state = CT_SHUTDOWN;
|
|
switch (band) {
|
default:
|
deb_info("Warning : Rf frequency (%iHz) is not in the supported range, using VHF switch ", fe->dtv_property_cache.frequency);
|
fallthrough;
|
case BAND_VHF:
|
state->dib8000_ops.set_gpio(fe, 3, 0, 1);
|
break;
|
case BAND_UHF:
|
state->dib8000_ops.set_gpio(fe, 3, 0, 0);
|
break;
|
}
|
|
ret = state->set_param_save(fe);
|
if (ret < 0)
|
return ret;
|
|
if (fe->dtv_property_cache.bandwidth_hz != 6000000) {
|
deb_info("only 6MHz bandwidth is supported\n");
|
return -EINVAL;
|
}
|
|
/* Update PLL if needed ratio */
|
state->dib8000_ops.update_pll(fe, &dib8090_pll_config_12mhz, fe->dtv_property_cache.bandwidth_hz / 1000, 0);
|
|
/* Get optimize PLL ratio to remove spurious */
|
pll_ratio = dib8090_compute_pll_parameters(fe);
|
if (pll_ratio == 17)
|
timf = 21387946;
|
else if (pll_ratio == 18)
|
timf = 20199727;
|
else if (pll_ratio == 19)
|
timf = 19136583;
|
else
|
timf = 18179756;
|
|
/* Update ratio */
|
state->dib8000_ops.update_pll(fe, &dib8090_pll_config_12mhz, fe->dtv_property_cache.bandwidth_hz / 1000, pll_ratio);
|
|
state->dib8000_ops.ctrl_timf(fe, DEMOD_TIMF_SET, timf);
|
|
if (band != BAND_CBAND) {
|
/* dib0090_get_wbd_target is returning any possible temperature compensated wbd-target */
|
target = (dib0090_get_wbd_target(fe) * 8 * 18 / 33 + 1) / 2;
|
state->dib8000_ops.set_wbd_ref(fe, target);
|
}
|
|
if (band == BAND_CBAND) {
|
deb_info("tuning in CBAND - soft-AGC startup\n");
|
dib0090_set_tune_state(fe, CT_AGC_START);
|
|
do {
|
ret = dib0090_gain_control(fe);
|
msleep(ret);
|
tune_state = dib0090_get_tune_state(fe);
|
if (tune_state == CT_AGC_STEP_0)
|
state->dib8000_ops.set_gpio(fe, 6, 0, 1);
|
else if (tune_state == CT_AGC_STEP_1) {
|
dib0090_get_current_gain(fe, NULL, NULL, &rf_gain_limit, <gain);
|
if (rf_gain_limit < 2000) /* activate the external attenuator in case of very high input power */
|
state->dib8000_ops.set_gpio(fe, 6, 0, 0);
|
}
|
} while (tune_state < CT_AGC_STOP);
|
|
deb_info("switching to PWM AGC\n");
|
dib0090_pwm_gain_reset(fe);
|
state->dib8000_ops.pwm_agc_reset(fe);
|
state->dib8000_ops.set_tune_state(fe, CT_DEMOD_START);
|
} else {
|
/* for everything else than CBAND we are using standard AGC */
|
deb_info("not tuning in CBAND - standard AGC startup\n");
|
dib0090_pwm_gain_reset(fe);
|
}
|
|
return 0;
|
}
|
|
static int dib809x_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *st = adap->priv;
|
struct i2c_adapter *tun_i2c = st->dib8000_ops.get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_TUNER, 1);
|
|
/* FIXME: if adap->id != 0, check if it is fe_adap[1] */
|
if (!dvb_attach(dib0090_register, adap->fe_adap[0].fe, tun_i2c, &dib809x_dib0090_config))
|
return -ENODEV;
|
|
st->set_param_save = adap->fe_adap[0].fe->ops.tuner_ops.set_params;
|
adap->fe_adap[0].fe->ops.tuner_ops.set_params = dib8096_set_param_override;
|
return 0;
|
}
|
|
static int stk809x_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib8000_attach, &state->dib8000_ops))
|
return -ENODEV;
|
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
state->dib8000_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 18, 0x80, 0);
|
|
adap->fe_adap[0].fe = state->dib8000_ops.init(&adap->dev->i2c_adap, 0x80, &dib809x_dib8000_config[0]);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int stk809x_frontend1_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib8000_attach, &state->dib8000_ops))
|
return -ENODEV;
|
|
state->dib8000_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 0x10, 0x82, 0);
|
|
adap->fe_adap[0].fe = state->dib8000_ops.init(&adap->dev->i2c_adap, 0x82, &dib809x_dib8000_config[1]);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int nim8096md_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *st = adap->priv;
|
struct i2c_adapter *tun_i2c;
|
struct dvb_frontend *fe_slave = st->dib8000_ops.get_slave_frontend(adap->fe_adap[0].fe, 1);
|
|
if (fe_slave) {
|
tun_i2c = st->dib8000_ops.get_i2c_master(fe_slave, DIBX000_I2C_INTERFACE_TUNER, 1);
|
if (dvb_attach(dib0090_register, fe_slave, tun_i2c, &dib809x_dib0090_config) == NULL)
|
return -ENODEV;
|
fe_slave->dvb = adap->fe_adap[0].fe->dvb;
|
fe_slave->ops.tuner_ops.set_params = dib8096_set_param_override;
|
}
|
tun_i2c = st->dib8000_ops.get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_TUNER, 1);
|
if (dvb_attach(dib0090_register, adap->fe_adap[0].fe, tun_i2c, &dib809x_dib0090_config) == NULL)
|
return -ENODEV;
|
|
st->set_param_save = adap->fe_adap[0].fe->ops.tuner_ops.set_params;
|
adap->fe_adap[0].fe->ops.tuner_ops.set_params = dib8096_set_param_override;
|
|
return 0;
|
}
|
|
static int nim8096md_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dvb_frontend *fe_slave;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib8000_attach, &state->dib8000_ops))
|
return -ENODEV;
|
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(1000);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
state->dib8000_ops.i2c_enumeration(&adap->dev->i2c_adap, 2, 18, 0x80, 0);
|
|
adap->fe_adap[0].fe = state->dib8000_ops.init(&adap->dev->i2c_adap, 0x80, &dib809x_dib8000_config[0]);
|
if (adap->fe_adap[0].fe == NULL)
|
return -ENODEV;
|
|
/* Needed to increment refcount */
|
if (!dvb_attach(dib8000_attach, &state->dib8000_ops))
|
return -ENODEV;
|
|
fe_slave = state->dib8000_ops.init(&adap->dev->i2c_adap, 0x82, &dib809x_dib8000_config[1]);
|
state->dib8000_ops.set_slave_frontend(adap->fe_adap[0].fe, fe_slave);
|
|
return fe_slave == NULL ? -ENODEV : 0;
|
}
|
|
/* TFE8096P */
|
static struct dibx000_agc_config dib8096p_agc_config[2] = {
|
{
|
.band_caps = BAND_UHF,
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0,
|
P_agc_freq_pwm_div=1, P_agc_inv_pwm1=0,
|
P_agc_inv_pwm2=0, P_agc_inh_dc_rv_est=0,
|
P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=5,
|
P_agc_write=0 */
|
.setup = (0 << 15) | (0 << 14) | (5 << 11)
|
| (0 << 10) | (0 << 9) | (0 << 8) | (3 << 5)
|
| (0 << 4) | (5 << 1) | (0 << 0),
|
|
.inv_gain = 684,
|
.time_stabiliz = 10,
|
|
.alpha_level = 0,
|
.thlock = 118,
|
|
.wbd_inv = 0,
|
.wbd_ref = 1200,
|
.wbd_sel = 3,
|
.wbd_alpha = 5,
|
|
.agc1_max = 65535,
|
.agc1_min = 0,
|
|
.agc2_max = 32767,
|
.agc2_min = 0,
|
|
.agc1_pt1 = 0,
|
.agc1_pt2 = 0,
|
.agc1_pt3 = 105,
|
.agc1_slope1 = 0,
|
.agc1_slope2 = 156,
|
.agc2_pt1 = 105,
|
.agc2_pt2 = 255,
|
.agc2_slope1 = 54,
|
.agc2_slope2 = 0,
|
|
.alpha_mant = 28,
|
.alpha_exp = 26,
|
.beta_mant = 31,
|
.beta_exp = 51,
|
|
.perform_agc_softsplit = 0,
|
} , {
|
.band_caps = BAND_FM | BAND_VHF | BAND_CBAND,
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0,
|
P_agc_freq_pwm_div=1, P_agc_inv_pwm1=0,
|
P_agc_inv_pwm2=0, P_agc_inh_dc_rv_est=0,
|
P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=5,
|
P_agc_write=0 */
|
.setup = (0 << 15) | (0 << 14) | (5 << 11)
|
| (0 << 10) | (0 << 9) | (0 << 8) | (3 << 5)
|
| (0 << 4) | (5 << 1) | (0 << 0),
|
|
.inv_gain = 732,
|
.time_stabiliz = 10,
|
|
.alpha_level = 0,
|
.thlock = 118,
|
|
.wbd_inv = 0,
|
.wbd_ref = 1200,
|
.wbd_sel = 3,
|
.wbd_alpha = 5,
|
|
.agc1_max = 65535,
|
.agc1_min = 0,
|
|
.agc2_max = 32767,
|
.agc2_min = 0,
|
|
.agc1_pt1 = 0,
|
.agc1_pt2 = 0,
|
.agc1_pt3 = 98,
|
.agc1_slope1 = 0,
|
.agc1_slope2 = 167,
|
.agc2_pt1 = 98,
|
.agc2_pt2 = 255,
|
.agc2_slope1 = 52,
|
.agc2_slope2 = 0,
|
|
.alpha_mant = 28,
|
.alpha_exp = 26,
|
.beta_mant = 31,
|
.beta_exp = 51,
|
|
.perform_agc_softsplit = 0,
|
}
|
};
|
|
static struct dibx000_bandwidth_config dib8096p_clock_config_12_mhz = {
|
.internal = 108000,
|
.sampling = 13500,
|
.pll_prediv = 1,
|
.pll_ratio = 9,
|
.pll_range = 1,
|
.pll_reset = 0,
|
.pll_bypass = 0,
|
.enable_refdiv = 0,
|
.bypclk_div = 0,
|
.IO_CLK_en_core = 0,
|
.ADClkSrc = 0,
|
.modulo = 2,
|
.sad_cfg = (3 << 14) | (1 << 12) | (524 << 0),
|
.ifreq = (0 << 25) | 0,
|
.timf = 20199729,
|
.xtal_hz = 12000000,
|
};
|
|
static struct dib8000_config tfe8096p_dib8000_config = {
|
.output_mpeg2_in_188_bytes = 1,
|
.hostbus_diversity = 1,
|
.update_lna = NULL,
|
|
.agc_config_count = 2,
|
.agc = dib8096p_agc_config,
|
.pll = &dib8096p_clock_config_12_mhz,
|
|
.gpio_dir = DIB8000_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB8000_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB8000_GPIO_DEFAULT_PWM_POS,
|
|
.agc_control = NULL,
|
.diversity_delay = 48,
|
.output_mode = OUTMODE_MPEG2_FIFO,
|
.enMpegOutput = 1,
|
};
|
|
static struct dib0090_wbd_slope dib8096p_wbd_table[] = {
|
{ 380, 81, 850, 64, 540, 4},
|
{ 860, 51, 866, 21, 375, 4},
|
{1700, 0, 250, 0, 100, 6},
|
{2600, 0, 250, 0, 100, 6},
|
{ 0xFFFF, 0, 0, 0, 0, 0},
|
};
|
|
static struct dib0090_config tfe8096p_dib0090_config = {
|
.io.clock_khz = 12000,
|
.io.pll_bypass = 0,
|
.io.pll_range = 0,
|
.io.pll_prediv = 3,
|
.io.pll_loopdiv = 6,
|
.io.adc_clock_ratio = 0,
|
.io.pll_int_loop_filt = 0,
|
|
.freq_offset_khz_uhf = -143,
|
.freq_offset_khz_vhf = -143,
|
|
.get_adc_power = dib8090_get_adc_power,
|
|
.clkouttobamse = 1,
|
.analog_output = 0,
|
|
.wbd_vhf_offset = 0,
|
.wbd_cband_offset = 0,
|
.use_pwm_agc = 1,
|
.clkoutdrive = 0,
|
|
.fref_clock_ratio = 1,
|
|
.ls_cfg_pad_drv = 0,
|
.data_tx_drv = 0,
|
.low_if = NULL,
|
.in_soc = 1,
|
.force_cband_input = 0,
|
};
|
|
struct dibx090p_adc {
|
u32 freq; /* RF freq MHz */
|
u32 timf; /* New Timf */
|
u32 pll_loopdiv; /* New prediv */
|
u32 pll_prediv; /* New loopdiv */
|
};
|
|
struct dibx090p_best_adc {
|
u32 timf;
|
u32 pll_loopdiv;
|
u32 pll_prediv;
|
};
|
|
static int dib8096p_get_best_sampling(struct dvb_frontend *fe, struct dibx090p_best_adc *adc)
|
{
|
u8 spur = 0, prediv = 0, loopdiv = 0, min_prediv = 1, max_prediv = 1;
|
u16 xtal = 12000;
|
u16 fcp_min = 1900; /* PLL, Minimum Frequency of phase comparator (KHz) */
|
u16 fcp_max = 20000; /* PLL, Maximum Frequency of phase comparator (KHz) */
|
u32 fmem_max = 140000; /* 140MHz max SDRAM freq */
|
u32 fdem_min = 66000;
|
u32 fcp = 0, fs = 0, fdem = 0, fmem = 0;
|
u32 harmonic_id = 0;
|
|
adc->timf = 0;
|
adc->pll_loopdiv = loopdiv;
|
adc->pll_prediv = prediv;
|
|
deb_info("bandwidth = %d", fe->dtv_property_cache.bandwidth_hz);
|
|
/* Find Min and Max prediv */
|
while ((xtal / max_prediv) >= fcp_min)
|
max_prediv++;
|
|
max_prediv--;
|
min_prediv = max_prediv;
|
while ((xtal / min_prediv) <= fcp_max) {
|
min_prediv--;
|
if (min_prediv == 1)
|
break;
|
}
|
deb_info("MIN prediv = %d : MAX prediv = %d", min_prediv, max_prediv);
|
|
min_prediv = 1;
|
|
for (prediv = min_prediv; prediv < max_prediv; prediv++) {
|
fcp = xtal / prediv;
|
if (fcp > fcp_min && fcp < fcp_max) {
|
for (loopdiv = 1; loopdiv < 64; loopdiv++) {
|
fmem = ((xtal/prediv) * loopdiv);
|
fdem = fmem / 2;
|
fs = fdem / 4;
|
|
/* test min/max system restrictions */
|
if ((fdem >= fdem_min) && (fmem <= fmem_max) && (fs >= fe->dtv_property_cache.bandwidth_hz / 1000)) {
|
spur = 0;
|
/* test fs harmonics positions */
|
for (harmonic_id = (fe->dtv_property_cache.frequency / (1000 * fs)); harmonic_id <= ((fe->dtv_property_cache.frequency / (1000 * fs)) + 1); harmonic_id++) {
|
if (((fs * harmonic_id) >= (fe->dtv_property_cache.frequency / 1000 - (fe->dtv_property_cache.bandwidth_hz / 2000))) && ((fs * harmonic_id) <= (fe->dtv_property_cache.frequency / 1000 + (fe->dtv_property_cache.bandwidth_hz / 2000)))) {
|
spur = 1;
|
break;
|
}
|
}
|
|
if (!spur) {
|
adc->pll_loopdiv = loopdiv;
|
adc->pll_prediv = prediv;
|
adc->timf = (4260880253U / fdem) * (1 << 8);
|
adc->timf += ((4260880253U % fdem) << 8) / fdem;
|
|
deb_info("RF %6d; BW %6d; Xtal %6d; Fmem %6d; Fdem %6d; Fs %6d; Prediv %2d; Loopdiv %2d; Timf %8d;", fe->dtv_property_cache.frequency, fe->dtv_property_cache.bandwidth_hz, xtal, fmem, fdem, fs, prediv, loopdiv, adc->timf);
|
break;
|
}
|
}
|
}
|
}
|
if (!spur)
|
break;
|
}
|
|
if (adc->pll_loopdiv == 0 && adc->pll_prediv == 0)
|
return -EINVAL;
|
return 0;
|
}
|
|
static int dib8096p_agc_startup(struct dvb_frontend *fe)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
struct dibx000_bandwidth_config pll;
|
struct dibx090p_best_adc adc;
|
u16 target;
|
int ret;
|
|
ret = state->set_param_save(fe);
|
if (ret < 0)
|
return ret;
|
memset(&pll, 0, sizeof(struct dibx000_bandwidth_config));
|
|
dib0090_pwm_gain_reset(fe);
|
/* dib0090_get_wbd_target is returning any possible
|
temperature compensated wbd-target */
|
target = (dib0090_get_wbd_target(fe) * 8 + 1) / 2;
|
state->dib8000_ops.set_wbd_ref(fe, target);
|
|
if (dib8096p_get_best_sampling(fe, &adc) == 0) {
|
pll.pll_ratio = adc.pll_loopdiv;
|
pll.pll_prediv = adc.pll_prediv;
|
|
dib0700_set_i2c_speed(adap->dev, 200);
|
state->dib8000_ops.update_pll(fe, &pll, fe->dtv_property_cache.bandwidth_hz / 1000, 0);
|
state->dib8000_ops.ctrl_timf(fe, DEMOD_TIMF_SET, adc.timf);
|
dib0700_set_i2c_speed(adap->dev, 1000);
|
}
|
return 0;
|
}
|
|
static int tfe8096p_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_state *st = adap->dev->priv;
|
u32 fw_version;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib8000_attach, &state->dib8000_ops))
|
return -ENODEV;
|
|
dib0700_get_version(adap->dev, NULL, NULL, &fw_version, NULL);
|
if (fw_version >= 0x10200)
|
st->fw_use_new_i2c_api = 1;
|
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
state->dib8000_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 0x10, 0x80, 1);
|
|
adap->fe_adap[0].fe = state->dib8000_ops.init(&adap->dev->i2c_adap,
|
0x80, &tfe8096p_dib8000_config);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int tfe8096p_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *st = adap->priv;
|
struct i2c_adapter *tun_i2c = st->dib8000_ops.get_i2c_tuner(adap->fe_adap[0].fe);
|
|
tfe8096p_dib0090_config.reset = st->dib8000_ops.tuner_sleep;
|
tfe8096p_dib0090_config.sleep = st->dib8000_ops.tuner_sleep;
|
tfe8096p_dib0090_config.wbd = dib8096p_wbd_table;
|
|
if (dvb_attach(dib0090_register, adap->fe_adap[0].fe, tun_i2c,
|
&tfe8096p_dib0090_config) == NULL)
|
return -ENODEV;
|
|
st->dib8000_ops.set_gpio(adap->fe_adap[0].fe, 8, 0, 1);
|
|
st->set_param_save = adap->fe_adap[0].fe->ops.tuner_ops.set_params;
|
adap->fe_adap[0].fe->ops.tuner_ops.set_params = dib8096p_agc_startup;
|
return 0;
|
}
|
|
/* STK9090M */
|
static int dib90x0_pid_filter(struct dvb_usb_adapter *adapter, int index, u16 pid, int onoff)
|
{
|
return dib9000_fw_pid_filter(adapter->fe_adap[0].fe, index, pid, onoff);
|
}
|
|
static int dib90x0_pid_filter_ctrl(struct dvb_usb_adapter *adapter, int onoff)
|
{
|
return dib9000_fw_pid_filter_ctrl(adapter->fe_adap[0].fe, onoff);
|
}
|
|
static int dib90x0_tuner_reset(struct dvb_frontend *fe, int onoff)
|
{
|
return dib9000_set_gpio(fe, 5, 0, !onoff);
|
}
|
|
static int dib90x0_tuner_sleep(struct dvb_frontend *fe, int onoff)
|
{
|
return dib9000_set_gpio(fe, 0, 0, onoff);
|
}
|
|
static int dib01x0_pmu_update(struct i2c_adapter *i2c, u16 *data, u8 len)
|
{
|
u8 wb[4] = { 0xc >> 8, 0xc & 0xff, 0, 0 };
|
u8 rb[2];
|
struct i2c_msg msg[2] = {
|
{.addr = 0x1e >> 1, .flags = 0, .buf = wb, .len = 2},
|
{.addr = 0x1e >> 1, .flags = I2C_M_RD, .buf = rb, .len = 2},
|
};
|
u8 index_data;
|
|
dibx000_i2c_set_speed(i2c, 250);
|
|
if (i2c_transfer(i2c, msg, 2) != 2)
|
return -EIO;
|
|
switch (rb[0] << 8 | rb[1]) {
|
case 0:
|
deb_info("Found DiB0170 rev1: This version of DiB0170 is not supported any longer.\n");
|
return -EIO;
|
case 1:
|
deb_info("Found DiB0170 rev2");
|
break;
|
case 2:
|
deb_info("Found DiB0190 rev2");
|
break;
|
default:
|
deb_info("DiB01x0 not found");
|
return -EIO;
|
}
|
|
for (index_data = 0; index_data < len; index_data += 2) {
|
wb[2] = (data[index_data + 1] >> 8) & 0xff;
|
wb[3] = (data[index_data + 1]) & 0xff;
|
|
if (data[index_data] == 0) {
|
wb[0] = (data[index_data] >> 8) & 0xff;
|
wb[1] = (data[index_data]) & 0xff;
|
msg[0].len = 2;
|
if (i2c_transfer(i2c, msg, 2) != 2)
|
return -EIO;
|
wb[2] |= rb[0];
|
wb[3] |= rb[1] & ~(3 << 4);
|
}
|
|
wb[0] = (data[index_data] >> 8)&0xff;
|
wb[1] = (data[index_data])&0xff;
|
msg[0].len = 4;
|
if (i2c_transfer(i2c, &msg[0], 1) != 1)
|
return -EIO;
|
}
|
return 0;
|
}
|
|
static struct dib9000_config stk9090m_config = {
|
.output_mpeg2_in_188_bytes = 1,
|
.output_mode = OUTMODE_MPEG2_FIFO,
|
.vcxo_timer = 279620,
|
.timing_frequency = 20452225,
|
.demod_clock_khz = 60000,
|
.xtal_clock_khz = 30000,
|
.if_drives = (0 << 15) | (1 << 13) | (0 << 12) | (3 << 10) | (0 << 9) | (1 << 7) | (0 << 6) | (0 << 4) | (1 << 3) | (1 << 1) | (0),
|
.subband = {
|
2,
|
{
|
{ 240, { BOARD_GPIO_COMPONENT_DEMOD, BOARD_GPIO_FUNCTION_SUBBAND_GPIO, 0x0008, 0x0000, 0x0008 } }, /* GPIO 3 to 1 for VHF */
|
{ 890, { BOARD_GPIO_COMPONENT_DEMOD, BOARD_GPIO_FUNCTION_SUBBAND_GPIO, 0x0008, 0x0000, 0x0000 } }, /* GPIO 3 to 0 for UHF */
|
{ 0 },
|
},
|
},
|
.gpio_function = {
|
{ .component = BOARD_GPIO_COMPONENT_DEMOD, .function = BOARD_GPIO_FUNCTION_COMPONENT_ON, .mask = 0x10 | 0x21, .direction = 0 & ~0x21, .value = (0x10 & ~0x1) | 0x20 },
|
{ .component = BOARD_GPIO_COMPONENT_DEMOD, .function = BOARD_GPIO_FUNCTION_COMPONENT_OFF, .mask = 0x10 | 0x21, .direction = 0 & ~0x21, .value = 0 | 0x21 },
|
},
|
};
|
|
static struct dib9000_config nim9090md_config[2] = {
|
{
|
.output_mpeg2_in_188_bytes = 1,
|
.output_mode = OUTMODE_MPEG2_FIFO,
|
.vcxo_timer = 279620,
|
.timing_frequency = 20452225,
|
.demod_clock_khz = 60000,
|
.xtal_clock_khz = 30000,
|
.if_drives = (0 << 15) | (1 << 13) | (0 << 12) | (3 << 10) | (0 << 9) | (1 << 7) | (0 << 6) | (0 << 4) | (1 << 3) | (1 << 1) | (0),
|
}, {
|
.output_mpeg2_in_188_bytes = 1,
|
.output_mode = OUTMODE_DIVERSITY,
|
.vcxo_timer = 279620,
|
.timing_frequency = 20452225,
|
.demod_clock_khz = 60000,
|
.xtal_clock_khz = 30000,
|
.if_drives = (0 << 15) | (1 << 13) | (0 << 12) | (3 << 10) | (0 << 9) | (1 << 7) | (0 << 6) | (0 << 4) | (1 << 3) | (1 << 1) | (0),
|
.subband = {
|
2,
|
{
|
{ 240, { BOARD_GPIO_COMPONENT_DEMOD, BOARD_GPIO_FUNCTION_SUBBAND_GPIO, 0x0006, 0x0000, 0x0006 } }, /* GPIO 1 and 2 to 1 for VHF */
|
{ 890, { BOARD_GPIO_COMPONENT_DEMOD, BOARD_GPIO_FUNCTION_SUBBAND_GPIO, 0x0006, 0x0000, 0x0000 } }, /* GPIO 1 and 2 to 0 for UHF */
|
{ 0 },
|
},
|
},
|
.gpio_function = {
|
{ .component = BOARD_GPIO_COMPONENT_DEMOD, .function = BOARD_GPIO_FUNCTION_COMPONENT_ON, .mask = 0x10 | 0x21, .direction = 0 & ~0x21, .value = (0x10 & ~0x1) | 0x20 },
|
{ .component = BOARD_GPIO_COMPONENT_DEMOD, .function = BOARD_GPIO_FUNCTION_COMPONENT_OFF, .mask = 0x10 | 0x21, .direction = 0 & ~0x21, .value = 0 | 0x21 },
|
},
|
}
|
};
|
|
static struct dib0090_config dib9090_dib0090_config = {
|
.io.pll_bypass = 0,
|
.io.pll_range = 1,
|
.io.pll_prediv = 1,
|
.io.pll_loopdiv = 8,
|
.io.adc_clock_ratio = 8,
|
.io.pll_int_loop_filt = 0,
|
.io.clock_khz = 30000,
|
.reset = dib90x0_tuner_reset,
|
.sleep = dib90x0_tuner_sleep,
|
.clkouttobamse = 0,
|
.analog_output = 0,
|
.use_pwm_agc = 0,
|
.clkoutdrive = 0,
|
.freq_offset_khz_uhf = 0,
|
.freq_offset_khz_vhf = 0,
|
};
|
|
static struct dib0090_config nim9090md_dib0090_config[2] = {
|
{
|
.io.pll_bypass = 0,
|
.io.pll_range = 1,
|
.io.pll_prediv = 1,
|
.io.pll_loopdiv = 8,
|
.io.adc_clock_ratio = 8,
|
.io.pll_int_loop_filt = 0,
|
.io.clock_khz = 30000,
|
.reset = dib90x0_tuner_reset,
|
.sleep = dib90x0_tuner_sleep,
|
.clkouttobamse = 1,
|
.analog_output = 0,
|
.use_pwm_agc = 0,
|
.clkoutdrive = 0,
|
.freq_offset_khz_uhf = 0,
|
.freq_offset_khz_vhf = 0,
|
}, {
|
.io.pll_bypass = 0,
|
.io.pll_range = 1,
|
.io.pll_prediv = 1,
|
.io.pll_loopdiv = 8,
|
.io.adc_clock_ratio = 8,
|
.io.pll_int_loop_filt = 0,
|
.io.clock_khz = 30000,
|
.reset = dib90x0_tuner_reset,
|
.sleep = dib90x0_tuner_sleep,
|
.clkouttobamse = 0,
|
.analog_output = 0,
|
.use_pwm_agc = 0,
|
.clkoutdrive = 0,
|
.freq_offset_khz_uhf = 0,
|
.freq_offset_khz_vhf = 0,
|
}
|
};
|
|
|
static int stk9090m_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
struct dib0700_state *st = adap->dev->priv;
|
u32 fw_version;
|
|
/* Make use of the new i2c functions from FW 1.20 */
|
dib0700_get_version(adap->dev, NULL, NULL, &fw_version, NULL);
|
if (fw_version >= 0x10200)
|
st->fw_use_new_i2c_api = 1;
|
dib0700_set_i2c_speed(adap->dev, 340);
|
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
dib9000_i2c_enumeration(&adap->dev->i2c_adap, 1, 0x10, 0x80);
|
|
if (request_firmware(&state->frontend_firmware, "dib9090.fw", &adap->dev->udev->dev)) {
|
deb_info("%s: Upload failed. (file not found?)\n", __func__);
|
return -ENODEV;
|
} else {
|
deb_info("%s: firmware read %zu bytes.\n", __func__, state->frontend_firmware->size);
|
}
|
stk9090m_config.microcode_B_fe_size = state->frontend_firmware->size;
|
stk9090m_config.microcode_B_fe_buffer = state->frontend_firmware->data;
|
|
adap->fe_adap[0].fe = dvb_attach(dib9000_attach, &adap->dev->i2c_adap, 0x80, &stk9090m_config);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int dib9090_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
struct i2c_adapter *i2c = dib9000_get_tuner_interface(adap->fe_adap[0].fe);
|
u16 data_dib190[10] = {
|
1, 0x1374,
|
2, 0x01a2,
|
7, 0x0020,
|
0, 0x00ef,
|
8, 0x0486,
|
};
|
|
if (!IS_ENABLED(CONFIG_DVB_DIB9000))
|
return -ENODEV;
|
if (dvb_attach(dib0090_fw_register, adap->fe_adap[0].fe, i2c, &dib9090_dib0090_config) == NULL)
|
return -ENODEV;
|
i2c = dib9000_get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_GPIO_1_2, 0);
|
if (!i2c)
|
return -ENODEV;
|
if (dib01x0_pmu_update(i2c, data_dib190, 10) != 0)
|
return -ENODEV;
|
dib0700_set_i2c_speed(adap->dev, 1500);
|
if (dib9000_firmware_post_pll_init(adap->fe_adap[0].fe) < 0)
|
return -ENODEV;
|
release_firmware(state->frontend_firmware);
|
return 0;
|
}
|
|
static int nim9090md_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
struct dib0700_state *st = adap->dev->priv;
|
struct i2c_adapter *i2c;
|
struct dvb_frontend *fe_slave;
|
u32 fw_version;
|
|
/* Make use of the new i2c functions from FW 1.20 */
|
dib0700_get_version(adap->dev, NULL, NULL, &fw_version, NULL);
|
if (fw_version >= 0x10200)
|
st->fw_use_new_i2c_api = 1;
|
dib0700_set_i2c_speed(adap->dev, 340);
|
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
if (request_firmware(&state->frontend_firmware, "dib9090.fw", &adap->dev->udev->dev)) {
|
deb_info("%s: Upload failed. (file not found?)\n", __func__);
|
return -EIO;
|
} else {
|
deb_info("%s: firmware read %zu bytes.\n", __func__, state->frontend_firmware->size);
|
}
|
nim9090md_config[0].microcode_B_fe_size = state->frontend_firmware->size;
|
nim9090md_config[0].microcode_B_fe_buffer = state->frontend_firmware->data;
|
nim9090md_config[1].microcode_B_fe_size = state->frontend_firmware->size;
|
nim9090md_config[1].microcode_B_fe_buffer = state->frontend_firmware->data;
|
|
dib9000_i2c_enumeration(&adap->dev->i2c_adap, 1, 0x20, 0x80);
|
adap->fe_adap[0].fe = dvb_attach(dib9000_attach, &adap->dev->i2c_adap, 0x80, &nim9090md_config[0]);
|
|
if (adap->fe_adap[0].fe == NULL)
|
return -ENODEV;
|
|
i2c = dib9000_get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_GPIO_3_4, 0);
|
dib9000_i2c_enumeration(i2c, 1, 0x12, 0x82);
|
|
fe_slave = dvb_attach(dib9000_attach, i2c, 0x82, &nim9090md_config[1]);
|
dib9000_set_slave_frontend(adap->fe_adap[0].fe, fe_slave);
|
|
return fe_slave == NULL ? -ENODEV : 0;
|
}
|
|
static int nim9090md_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
struct i2c_adapter *i2c;
|
struct dvb_frontend *fe_slave;
|
u16 data_dib190[10] = {
|
1, 0x5374,
|
2, 0x01ae,
|
7, 0x0020,
|
0, 0x00ef,
|
8, 0x0406,
|
};
|
if (!IS_ENABLED(CONFIG_DVB_DIB9000))
|
return -ENODEV;
|
i2c = dib9000_get_tuner_interface(adap->fe_adap[0].fe);
|
if (dvb_attach(dib0090_fw_register, adap->fe_adap[0].fe, i2c, &nim9090md_dib0090_config[0]) == NULL)
|
return -ENODEV;
|
i2c = dib9000_get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_GPIO_1_2, 0);
|
if (!i2c)
|
return -ENODEV;
|
if (dib01x0_pmu_update(i2c, data_dib190, 10) < 0)
|
return -ENODEV;
|
|
dib0700_set_i2c_speed(adap->dev, 1500);
|
if (dib9000_firmware_post_pll_init(adap->fe_adap[0].fe) < 0)
|
return -ENODEV;
|
|
fe_slave = dib9000_get_slave_frontend(adap->fe_adap[0].fe, 1);
|
if (fe_slave != NULL) {
|
i2c = dib9000_get_component_bus_interface(adap->fe_adap[0].fe);
|
dib9000_set_i2c_adapter(fe_slave, i2c);
|
|
i2c = dib9000_get_tuner_interface(fe_slave);
|
if (dvb_attach(dib0090_fw_register, fe_slave, i2c, &nim9090md_dib0090_config[1]) == NULL)
|
return -ENODEV;
|
fe_slave->dvb = adap->fe_adap[0].fe->dvb;
|
dib9000_fw_set_component_bus_speed(adap->fe_adap[0].fe, 1500);
|
if (dib9000_firmware_post_pll_init(fe_slave) < 0)
|
return -ENODEV;
|
}
|
release_firmware(state->frontend_firmware);
|
|
return 0;
|
}
|
|
/* NIM7090 */
|
static int dib7090p_get_best_sampling(struct dvb_frontend *fe , struct dibx090p_best_adc *adc)
|
{
|
u8 spur = 0, prediv = 0, loopdiv = 0, min_prediv = 1, max_prediv = 1;
|
|
u16 xtal = 12000;
|
u32 fcp_min = 1900; /* PLL Minimum Frequency comparator KHz */
|
u32 fcp_max = 20000; /* PLL Maximum Frequency comparator KHz */
|
u32 fdem_max = 76000;
|
u32 fdem_min = 69500;
|
u32 fcp = 0, fs = 0, fdem = 0;
|
u32 harmonic_id = 0;
|
|
adc->pll_loopdiv = loopdiv;
|
adc->pll_prediv = prediv;
|
adc->timf = 0;
|
|
deb_info("bandwidth = %d fdem_min =%d", fe->dtv_property_cache.bandwidth_hz, fdem_min);
|
|
/* Find Min and Max prediv */
|
while ((xtal/max_prediv) >= fcp_min)
|
max_prediv++;
|
|
max_prediv--;
|
min_prediv = max_prediv;
|
while ((xtal/min_prediv) <= fcp_max) {
|
min_prediv--;
|
if (min_prediv == 1)
|
break;
|
}
|
deb_info("MIN prediv = %d : MAX prediv = %d", min_prediv, max_prediv);
|
|
min_prediv = 2;
|
|
for (prediv = min_prediv ; prediv < max_prediv; prediv++) {
|
fcp = xtal / prediv;
|
if (fcp > fcp_min && fcp < fcp_max) {
|
for (loopdiv = 1 ; loopdiv < 64 ; loopdiv++) {
|
fdem = ((xtal/prediv) * loopdiv);
|
fs = fdem / 4;
|
/* test min/max system restrictions */
|
|
if ((fdem >= fdem_min) && (fdem <= fdem_max) && (fs >= fe->dtv_property_cache.bandwidth_hz/1000)) {
|
spur = 0;
|
/* test fs harmonics positions */
|
for (harmonic_id = (fe->dtv_property_cache.frequency / (1000*fs)) ; harmonic_id <= ((fe->dtv_property_cache.frequency / (1000*fs))+1) ; harmonic_id++) {
|
if (((fs*harmonic_id) >= ((fe->dtv_property_cache.frequency/1000) - (fe->dtv_property_cache.bandwidth_hz/2000))) && ((fs*harmonic_id) <= ((fe->dtv_property_cache.frequency/1000) + (fe->dtv_property_cache.bandwidth_hz/2000)))) {
|
spur = 1;
|
break;
|
}
|
}
|
|
if (!spur) {
|
adc->pll_loopdiv = loopdiv;
|
adc->pll_prediv = prediv;
|
adc->timf = 2396745143UL/fdem*(1 << 9);
|
adc->timf += ((2396745143UL%fdem) << 9)/fdem;
|
deb_info("loopdiv=%i prediv=%i timf=%i", loopdiv, prediv, adc->timf);
|
break;
|
}
|
}
|
}
|
}
|
if (!spur)
|
break;
|
}
|
|
|
if (adc->pll_loopdiv == 0 && adc->pll_prediv == 0)
|
return -EINVAL;
|
else
|
return 0;
|
}
|
|
static int dib7090_agc_startup(struct dvb_frontend *fe)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
struct dibx000_bandwidth_config pll;
|
u16 target;
|
struct dibx090p_best_adc adc;
|
int ret;
|
|
ret = state->set_param_save(fe);
|
if (ret < 0)
|
return ret;
|
|
memset(&pll, 0, sizeof(struct dibx000_bandwidth_config));
|
dib0090_pwm_gain_reset(fe);
|
target = (dib0090_get_wbd_target(fe) * 8 + 1) / 2;
|
state->dib7000p_ops.set_wbd_ref(fe, target);
|
|
if (dib7090p_get_best_sampling(fe, &adc) == 0) {
|
pll.pll_ratio = adc.pll_loopdiv;
|
pll.pll_prediv = adc.pll_prediv;
|
|
state->dib7000p_ops.update_pll(fe, &pll);
|
state->dib7000p_ops.ctrl_timf(fe, DEMOD_TIMF_SET, adc.timf);
|
}
|
return 0;
|
}
|
|
static int dib7090_agc_restart(struct dvb_frontend *fe, u8 restart)
|
{
|
deb_info("AGC restart callback: %d", restart);
|
if (restart == 0) /* before AGC startup */
|
dib0090_set_dc_servo(fe, 1);
|
return 0;
|
}
|
|
static int tfe7790p_update_lna(struct dvb_frontend *fe, u16 agc_global)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
deb_info("update LNA: agc global=%i", agc_global);
|
|
if (agc_global < 25000) {
|
state->dib7000p_ops.set_gpio(fe, 8, 0, 0);
|
state->dib7000p_ops.set_agc1_min(fe, 0);
|
} else {
|
state->dib7000p_ops.set_gpio(fe, 8, 0, 1);
|
state->dib7000p_ops.set_agc1_min(fe, 32768);
|
}
|
|
return 0;
|
}
|
|
static struct dib0090_wbd_slope dib7090_wbd_table[] = {
|
{ 380, 81, 850, 64, 540, 4},
|
{ 860, 51, 866, 21, 375, 4},
|
{1700, 0, 250, 0, 100, 6},
|
{2600, 0, 250, 0, 100, 6},
|
{ 0xFFFF, 0, 0, 0, 0, 0},
|
};
|
|
static struct dibx000_agc_config dib7090_agc_config[2] = {
|
{
|
.band_caps = BAND_UHF,
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=1, P_agc_inv_pwm1=0, P_agc_inv_pwm2=0,
|
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=5, P_agc_write=0 */
|
.setup = (0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) | (0 << 8) | (3 << 5) | (0 << 4) | (5 << 1) | (0 << 0),
|
|
.inv_gain = 687,
|
.time_stabiliz = 10,
|
|
.alpha_level = 0,
|
.thlock = 118,
|
|
.wbd_inv = 0,
|
.wbd_ref = 1200,
|
.wbd_sel = 3,
|
.wbd_alpha = 5,
|
|
.agc1_max = 65535,
|
.agc1_min = 32768,
|
|
.agc2_max = 65535,
|
.agc2_min = 0,
|
|
.agc1_pt1 = 0,
|
.agc1_pt2 = 32,
|
.agc1_pt3 = 114,
|
.agc1_slope1 = 143,
|
.agc1_slope2 = 144,
|
.agc2_pt1 = 114,
|
.agc2_pt2 = 227,
|
.agc2_slope1 = 116,
|
.agc2_slope2 = 117,
|
|
.alpha_mant = 18,
|
.alpha_exp = 0,
|
.beta_mant = 20,
|
.beta_exp = 59,
|
|
.perform_agc_softsplit = 0,
|
} , {
|
.band_caps = BAND_FM | BAND_VHF | BAND_CBAND,
|
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=1, P_agc_inv_pwm1=0, P_agc_inv_pwm2=0,
|
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=5, P_agc_write=0 */
|
.setup = (0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) | (0 << 8) | (3 << 5) | (0 << 4) | (5 << 1) | (0 << 0),
|
|
.inv_gain = 732,
|
.time_stabiliz = 10,
|
|
.alpha_level = 0,
|
.thlock = 118,
|
|
.wbd_inv = 0,
|
.wbd_ref = 1200,
|
.wbd_sel = 3,
|
.wbd_alpha = 5,
|
|
.agc1_max = 65535,
|
.agc1_min = 0,
|
|
.agc2_max = 65535,
|
.agc2_min = 0,
|
|
.agc1_pt1 = 0,
|
.agc1_pt2 = 0,
|
.agc1_pt3 = 98,
|
.agc1_slope1 = 0,
|
.agc1_slope2 = 167,
|
.agc2_pt1 = 98,
|
.agc2_pt2 = 255,
|
.agc2_slope1 = 104,
|
.agc2_slope2 = 0,
|
|
.alpha_mant = 18,
|
.alpha_exp = 0,
|
.beta_mant = 20,
|
.beta_exp = 59,
|
|
.perform_agc_softsplit = 0,
|
}
|
};
|
|
static struct dibx000_bandwidth_config dib7090_clock_config_12_mhz = {
|
.internal = 60000,
|
.sampling = 15000,
|
.pll_prediv = 1,
|
.pll_ratio = 5,
|
.pll_range = 0,
|
.pll_reset = 0,
|
.pll_bypass = 0,
|
.enable_refdiv = 0,
|
.bypclk_div = 0,
|
.IO_CLK_en_core = 1,
|
.ADClkSrc = 1,
|
.modulo = 2,
|
.sad_cfg = (3 << 14) | (1 << 12) | (524 << 0),
|
.ifreq = (0 << 25) | 0,
|
.timf = 20452225,
|
.xtal_hz = 15000000,
|
};
|
|
static struct dib7000p_config nim7090_dib7000p_config = {
|
.output_mpeg2_in_188_bytes = 1,
|
.hostbus_diversity = 1,
|
.tuner_is_baseband = 1,
|
.update_lna = tfe7790p_update_lna, /* GPIO used is the same as TFE7790 */
|
|
.agc_config_count = 2,
|
.agc = dib7090_agc_config,
|
|
.bw = &dib7090_clock_config_12_mhz,
|
|
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
|
|
.pwm_freq_div = 0,
|
|
.agc_control = dib7090_agc_restart,
|
|
.spur_protect = 0,
|
.disable_sample_and_hold = 0,
|
.enable_current_mirror = 0,
|
.diversity_delay = 0,
|
|
.output_mode = OUTMODE_MPEG2_FIFO,
|
.enMpegOutput = 1,
|
};
|
|
static int tfe7090p_pvr_update_lna(struct dvb_frontend *fe, u16 agc_global)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
deb_info("TFE7090P-PVR update LNA: agc global=%i", agc_global);
|
if (agc_global < 25000) {
|
state->dib7000p_ops.set_gpio(fe, 5, 0, 0);
|
state->dib7000p_ops.set_agc1_min(fe, 0);
|
} else {
|
state->dib7000p_ops.set_gpio(fe, 5, 0, 1);
|
state->dib7000p_ops.set_agc1_min(fe, 32768);
|
}
|
|
return 0;
|
}
|
|
static struct dib7000p_config tfe7090pvr_dib7000p_config[2] = {
|
{
|
.output_mpeg2_in_188_bytes = 1,
|
.hostbus_diversity = 1,
|
.tuner_is_baseband = 1,
|
.update_lna = tfe7090p_pvr_update_lna,
|
|
.agc_config_count = 2,
|
.agc = dib7090_agc_config,
|
|
.bw = &dib7090_clock_config_12_mhz,
|
|
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
|
|
.pwm_freq_div = 0,
|
|
.agc_control = dib7090_agc_restart,
|
|
.spur_protect = 0,
|
.disable_sample_and_hold = 0,
|
.enable_current_mirror = 0,
|
.diversity_delay = 0,
|
|
.output_mode = OUTMODE_MPEG2_PAR_GATED_CLK,
|
.default_i2c_addr = 0x90,
|
.enMpegOutput = 1,
|
}, {
|
.output_mpeg2_in_188_bytes = 1,
|
.hostbus_diversity = 1,
|
.tuner_is_baseband = 1,
|
.update_lna = tfe7090p_pvr_update_lna,
|
|
.agc_config_count = 2,
|
.agc = dib7090_agc_config,
|
|
.bw = &dib7090_clock_config_12_mhz,
|
|
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
|
|
.pwm_freq_div = 0,
|
|
.agc_control = dib7090_agc_restart,
|
|
.spur_protect = 0,
|
.disable_sample_and_hold = 0,
|
.enable_current_mirror = 0,
|
.diversity_delay = 0,
|
|
.output_mode = OUTMODE_MPEG2_PAR_GATED_CLK,
|
.default_i2c_addr = 0x92,
|
.enMpegOutput = 0,
|
}
|
};
|
|
static struct dib0090_config nim7090_dib0090_config = {
|
.io.clock_khz = 12000,
|
.io.pll_bypass = 0,
|
.io.pll_range = 0,
|
.io.pll_prediv = 3,
|
.io.pll_loopdiv = 6,
|
.io.adc_clock_ratio = 0,
|
.io.pll_int_loop_filt = 0,
|
|
.freq_offset_khz_uhf = 0,
|
.freq_offset_khz_vhf = 0,
|
|
.clkouttobamse = 1,
|
.analog_output = 0,
|
|
.wbd_vhf_offset = 0,
|
.wbd_cband_offset = 0,
|
.use_pwm_agc = 1,
|
.clkoutdrive = 0,
|
|
.fref_clock_ratio = 0,
|
|
.wbd = dib7090_wbd_table,
|
|
.ls_cfg_pad_drv = 0,
|
.data_tx_drv = 0,
|
.low_if = NULL,
|
.in_soc = 1,
|
};
|
|
static struct dib7000p_config tfe7790p_dib7000p_config = {
|
.output_mpeg2_in_188_bytes = 1,
|
.hostbus_diversity = 1,
|
.tuner_is_baseband = 1,
|
.update_lna = tfe7790p_update_lna,
|
|
.agc_config_count = 2,
|
.agc = dib7090_agc_config,
|
|
.bw = &dib7090_clock_config_12_mhz,
|
|
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
|
|
.pwm_freq_div = 0,
|
|
.agc_control = dib7090_agc_restart,
|
|
.spur_protect = 0,
|
.disable_sample_and_hold = 0,
|
.enable_current_mirror = 0,
|
.diversity_delay = 0,
|
|
.output_mode = OUTMODE_MPEG2_PAR_GATED_CLK,
|
.enMpegOutput = 1,
|
};
|
|
static struct dib0090_config tfe7790p_dib0090_config = {
|
.io.clock_khz = 12000,
|
.io.pll_bypass = 0,
|
.io.pll_range = 0,
|
.io.pll_prediv = 3,
|
.io.pll_loopdiv = 6,
|
.io.adc_clock_ratio = 0,
|
.io.pll_int_loop_filt = 0,
|
|
.freq_offset_khz_uhf = 0,
|
.freq_offset_khz_vhf = 0,
|
|
.clkouttobamse = 1,
|
.analog_output = 0,
|
|
.wbd_vhf_offset = 0,
|
.wbd_cband_offset = 0,
|
.use_pwm_agc = 1,
|
.clkoutdrive = 0,
|
|
.fref_clock_ratio = 0,
|
|
.wbd = dib7090_wbd_table,
|
|
.ls_cfg_pad_drv = 0,
|
.data_tx_drv = 0,
|
.low_if = NULL,
|
.in_soc = 1,
|
.force_cband_input = 0,
|
.is_dib7090e = 0,
|
.force_crystal_mode = 1,
|
};
|
|
static struct dib0090_config tfe7090pvr_dib0090_config[2] = {
|
{
|
.io.clock_khz = 12000,
|
.io.pll_bypass = 0,
|
.io.pll_range = 0,
|
.io.pll_prediv = 3,
|
.io.pll_loopdiv = 6,
|
.io.adc_clock_ratio = 0,
|
.io.pll_int_loop_filt = 0,
|
|
.freq_offset_khz_uhf = 50,
|
.freq_offset_khz_vhf = 70,
|
|
.clkouttobamse = 1,
|
.analog_output = 0,
|
|
.wbd_vhf_offset = 0,
|
.wbd_cband_offset = 0,
|
.use_pwm_agc = 1,
|
.clkoutdrive = 0,
|
|
.fref_clock_ratio = 0,
|
|
.wbd = dib7090_wbd_table,
|
|
.ls_cfg_pad_drv = 0,
|
.data_tx_drv = 0,
|
.low_if = NULL,
|
.in_soc = 1,
|
}, {
|
.io.clock_khz = 12000,
|
.io.pll_bypass = 0,
|
.io.pll_range = 0,
|
.io.pll_prediv = 3,
|
.io.pll_loopdiv = 6,
|
.io.adc_clock_ratio = 0,
|
.io.pll_int_loop_filt = 0,
|
|
.freq_offset_khz_uhf = -50,
|
.freq_offset_khz_vhf = -70,
|
|
.clkouttobamse = 1,
|
.analog_output = 0,
|
|
.wbd_vhf_offset = 0,
|
.wbd_cband_offset = 0,
|
.use_pwm_agc = 1,
|
.clkoutdrive = 0,
|
|
.fref_clock_ratio = 0,
|
|
.wbd = dib7090_wbd_table,
|
|
.ls_cfg_pad_drv = 0,
|
.data_tx_drv = 0,
|
.low_if = NULL,
|
.in_soc = 1,
|
}
|
};
|
|
static int nim7090_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
if (state->dib7000p_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 0x10, &nim7090_dib7000p_config) != 0) {
|
err("%s: state->dib7000p_ops.i2c_enumeration failed. Cannot continue\n", __func__);
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap, 0x80, &nim7090_dib7000p_config);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int nim7090_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *st = adap->priv;
|
struct i2c_adapter *tun_i2c = st->dib7000p_ops.get_i2c_tuner(adap->fe_adap[0].fe);
|
|
nim7090_dib0090_config.reset = st->dib7000p_ops.tuner_sleep,
|
nim7090_dib0090_config.sleep = st->dib7000p_ops.tuner_sleep,
|
nim7090_dib0090_config.get_adc_power = st->dib7000p_ops.get_adc_power;
|
|
if (dvb_attach(dib0090_register, adap->fe_adap[0].fe, tun_i2c, &nim7090_dib0090_config) == NULL)
|
return -ENODEV;
|
|
st->dib7000p_ops.set_gpio(adap->fe_adap[0].fe, 8, 0, 1);
|
|
st->set_param_save = adap->fe_adap[0].fe->ops.tuner_ops.set_params;
|
adap->fe_adap[0].fe->ops.tuner_ops.set_params = dib7090_agc_startup;
|
return 0;
|
}
|
|
static int tfe7090pvr_frontend0_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_state *st = adap->dev->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
/* The TFE7090 requires the dib0700 to not be in master mode */
|
st->disable_streaming_master_mode = 1;
|
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
/* initialize IC 0 */
|
if (state->dib7000p_ops.i2c_enumeration(&adap->dev->i2c_adap, 1, 0x20, &tfe7090pvr_dib7000p_config[0]) != 0) {
|
err("%s: state->dib7000p_ops.i2c_enumeration failed. Cannot continue\n", __func__);
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
|
dib0700_set_i2c_speed(adap->dev, 340);
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap, 0x90, &tfe7090pvr_dib7000p_config[0]);
|
if (adap->fe_adap[0].fe == NULL)
|
return -ENODEV;
|
|
state->dib7000p_ops.slave_reset(adap->fe_adap[0].fe);
|
|
return 0;
|
}
|
|
static int tfe7090pvr_frontend1_attach(struct dvb_usb_adapter *adap)
|
{
|
struct i2c_adapter *i2c;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (adap->dev->adapter[0].fe_adap[0].fe == NULL) {
|
err("the master dib7090 has to be initialized first");
|
return -ENODEV; /* the master device has not been initialized */
|
}
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
i2c = state->dib7000p_ops.get_i2c_master(adap->dev->adapter[0].fe_adap[0].fe, DIBX000_I2C_INTERFACE_GPIO_6_7, 1);
|
if (state->dib7000p_ops.i2c_enumeration(i2c, 1, 0x10, &tfe7090pvr_dib7000p_config[1]) != 0) {
|
err("%s: state->dib7000p_ops.i2c_enumeration failed. Cannot continue\n", __func__);
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(i2c, 0x92, &tfe7090pvr_dib7000p_config[1]);
|
dib0700_set_i2c_speed(adap->dev, 200);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int tfe7090pvr_tuner0_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *st = adap->priv;
|
struct i2c_adapter *tun_i2c = st->dib7000p_ops.get_i2c_tuner(adap->fe_adap[0].fe);
|
|
tfe7090pvr_dib0090_config[0].reset = st->dib7000p_ops.tuner_sleep;
|
tfe7090pvr_dib0090_config[0].sleep = st->dib7000p_ops.tuner_sleep;
|
tfe7090pvr_dib0090_config[0].get_adc_power = st->dib7000p_ops.get_adc_power;
|
|
if (dvb_attach(dib0090_register, adap->fe_adap[0].fe, tun_i2c, &tfe7090pvr_dib0090_config[0]) == NULL)
|
return -ENODEV;
|
|
st->dib7000p_ops.set_gpio(adap->fe_adap[0].fe, 8, 0, 1);
|
|
st->set_param_save = adap->fe_adap[0].fe->ops.tuner_ops.set_params;
|
adap->fe_adap[0].fe->ops.tuner_ops.set_params = dib7090_agc_startup;
|
return 0;
|
}
|
|
static int tfe7090pvr_tuner1_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *st = adap->priv;
|
struct i2c_adapter *tun_i2c = st->dib7000p_ops.get_i2c_tuner(adap->fe_adap[0].fe);
|
|
tfe7090pvr_dib0090_config[1].reset = st->dib7000p_ops.tuner_sleep;
|
tfe7090pvr_dib0090_config[1].sleep = st->dib7000p_ops.tuner_sleep;
|
tfe7090pvr_dib0090_config[1].get_adc_power = st->dib7000p_ops.get_adc_power;
|
|
if (dvb_attach(dib0090_register, adap->fe_adap[0].fe, tun_i2c, &tfe7090pvr_dib0090_config[1]) == NULL)
|
return -ENODEV;
|
|
st->dib7000p_ops.set_gpio(adap->fe_adap[0].fe, 8, 0, 1);
|
|
st->set_param_save = adap->fe_adap[0].fe->ops.tuner_ops.set_params;
|
adap->fe_adap[0].fe->ops.tuner_ops.set_params = dib7090_agc_startup;
|
return 0;
|
}
|
|
static int tfe7790p_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_state *st = adap->dev->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
/* The TFE7790P requires the dib0700 to not be in master mode */
|
st->disable_streaming_master_mode = 1;
|
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
msleep(20);
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(20);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
if (state->dib7000p_ops.i2c_enumeration(&adap->dev->i2c_adap,
|
1, 0x10, &tfe7790p_dib7000p_config) != 0) {
|
err("%s: state->dib7000p_ops.i2c_enumeration failed. Cannot continue\n",
|
__func__);
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap,
|
0x80, &tfe7790p_dib7000p_config);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int tfe7790p_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *st = adap->priv;
|
struct i2c_adapter *tun_i2c =
|
st->dib7000p_ops.get_i2c_tuner(adap->fe_adap[0].fe);
|
|
|
tfe7790p_dib0090_config.reset = st->dib7000p_ops.tuner_sleep;
|
tfe7790p_dib0090_config.sleep = st->dib7000p_ops.tuner_sleep;
|
tfe7790p_dib0090_config.get_adc_power = st->dib7000p_ops.get_adc_power;
|
|
if (dvb_attach(dib0090_register, adap->fe_adap[0].fe, tun_i2c,
|
&tfe7790p_dib0090_config) == NULL)
|
return -ENODEV;
|
|
st->dib7000p_ops.set_gpio(adap->fe_adap[0].fe, 8, 0, 1);
|
|
st->set_param_save = adap->fe_adap[0].fe->ops.tuner_ops.set_params;
|
adap->fe_adap[0].fe->ops.tuner_ops.set_params = dib7090_agc_startup;
|
return 0;
|
}
|
|
/* STK7070PD */
|
static struct dib7000p_config stk7070pd_dib7000p_config[2] = {
|
{
|
.output_mpeg2_in_188_bytes = 1,
|
|
.agc_config_count = 1,
|
.agc = &dib7070_agc_config,
|
.bw = &dib7070_bw_config_12_mhz,
|
.tuner_is_baseband = 1,
|
.spur_protect = 1,
|
|
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
|
|
.hostbus_diversity = 1,
|
}, {
|
.output_mpeg2_in_188_bytes = 1,
|
|
.agc_config_count = 1,
|
.agc = &dib7070_agc_config,
|
.bw = &dib7070_bw_config_12_mhz,
|
.tuner_is_baseband = 1,
|
.spur_protect = 1,
|
|
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
|
|
.hostbus_diversity = 1,
|
}
|
};
|
|
static void stk7070pd_init(struct dvb_usb_device *dev)
|
{
|
dib0700_set_gpio(dev, GPIO6, GPIO_OUT, 1);
|
msleep(10);
|
dib0700_set_gpio(dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(dev, GPIO10, GPIO_OUT, 0);
|
|
dib0700_ctrl_clock(dev, 72, 1);
|
|
msleep(10);
|
dib0700_set_gpio(dev, GPIO10, GPIO_OUT, 1);
|
}
|
|
static int stk7070pd_frontend_attach0(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
stk7070pd_init(adap->dev);
|
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
|
if (state->dib7000p_ops.i2c_enumeration(&adap->dev->i2c_adap, 2, 18,
|
stk7070pd_dib7000p_config) != 0) {
|
err("%s: state->dib7000p_ops.i2c_enumeration failed. Cannot continue\n",
|
__func__);
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap, 0x80, &stk7070pd_dib7000p_config[0]);
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int stk7070pd_frontend_attach1(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap, 0x82, &stk7070pd_dib7000p_config[1]);
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int novatd_read_status_override(struct dvb_frontend *fe,
|
enum fe_status *stat)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dvb_usb_device *dev = adap->dev;
|
struct dib0700_state *state = dev->priv;
|
int ret;
|
|
ret = state->read_status(fe, stat);
|
|
if (!ret)
|
dib0700_set_gpio(dev, adap->id == 0 ? GPIO1 : GPIO0, GPIO_OUT,
|
!!(*stat & FE_HAS_LOCK));
|
|
return ret;
|
}
|
|
static int novatd_sleep_override(struct dvb_frontend* fe)
|
{
|
struct dvb_usb_adapter *adap = fe->dvb->priv;
|
struct dvb_usb_device *dev = adap->dev;
|
struct dib0700_state *state = dev->priv;
|
|
/* turn off LED */
|
dib0700_set_gpio(dev, adap->id == 0 ? GPIO1 : GPIO0, GPIO_OUT, 0);
|
|
return state->sleep(fe);
|
}
|
|
/*
|
* novatd_frontend_attach - Nova-TD specific attach
|
*
|
* Nova-TD has GPIO0, 1 and 2 for LEDs. So do not fiddle with them except for
|
* information purposes.
|
*/
|
static int novatd_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dvb_usb_device *dev = adap->dev;
|
struct dib0700_state *st = dev->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
if (adap->id == 0) {
|
stk7070pd_init(dev);
|
|
/* turn the power LED on, the other two off (just in case) */
|
dib0700_set_gpio(dev, GPIO0, GPIO_OUT, 0);
|
dib0700_set_gpio(dev, GPIO1, GPIO_OUT, 0);
|
dib0700_set_gpio(dev, GPIO2, GPIO_OUT, 1);
|
|
if (state->dib7000p_ops.i2c_enumeration(&dev->i2c_adap, 2, 18,
|
stk7070pd_dib7000p_config) != 0) {
|
err("%s: state->dib7000p_ops.i2c_enumeration failed. Cannot continue\n",
|
__func__);
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
}
|
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&dev->i2c_adap,
|
adap->id == 0 ? 0x80 : 0x82,
|
&stk7070pd_dib7000p_config[adap->id]);
|
|
if (adap->fe_adap[0].fe == NULL)
|
return -ENODEV;
|
|
st->read_status = adap->fe_adap[0].fe->ops.read_status;
|
adap->fe_adap[0].fe->ops.read_status = novatd_read_status_override;
|
st->sleep = adap->fe_adap[0].fe->ops.sleep;
|
adap->fe_adap[0].fe->ops.sleep = novatd_sleep_override;
|
|
return 0;
|
}
|
|
/* S5H1411 */
|
static struct s5h1411_config pinnacle_801e_config = {
|
.output_mode = S5H1411_PARALLEL_OUTPUT,
|
.gpio = S5H1411_GPIO_OFF,
|
.mpeg_timing = S5H1411_MPEGTIMING_NONCONTINUOUS_NONINVERTING_CLOCK,
|
.qam_if = S5H1411_IF_44000,
|
.vsb_if = S5H1411_IF_44000,
|
.inversion = S5H1411_INVERSION_OFF,
|
.status_mode = S5H1411_DEMODLOCKING
|
};
|
|
/* Pinnacle PCTV HD Pro 801e GPIOs map:
|
GPIO0 - currently unknown
|
GPIO1 - xc5000 tuner reset
|
GPIO2 - CX25843 sleep
|
GPIO3 - currently unknown
|
GPIO4 - currently unknown
|
GPIO6 - currently unknown
|
GPIO7 - currently unknown
|
GPIO9 - currently unknown
|
GPIO10 - CX25843 reset
|
*/
|
static int s5h1411_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_state *st = adap->dev->priv;
|
|
/* Make use of the new i2c functions from FW 1.20 */
|
st->fw_use_new_i2c_api = 1;
|
|
/* The s5h1411 requires the dib0700 to not be in master mode */
|
st->disable_streaming_master_mode = 1;
|
|
/* All msleep values taken from Windows USB trace */
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 0);
|
dib0700_set_gpio(adap->dev, GPIO3, GPIO_OUT, 0);
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(400);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
msleep(60);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(30);
|
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
|
dib0700_set_gpio(adap->dev, GPIO2, GPIO_OUT, 0);
|
msleep(30);
|
|
/* Put the CX25843 to sleep for now since we're in digital mode */
|
dib0700_set_gpio(adap->dev, GPIO2, GPIO_OUT, 1);
|
|
/* GPIOs are initialized, do the attach */
|
adap->fe_adap[0].fe = dvb_attach(s5h1411_attach, &pinnacle_801e_config,
|
&adap->dev->i2c_adap);
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int dib0700_xc5000_tuner_callback(void *priv, int component,
|
int command, int arg)
|
{
|
struct dvb_usb_adapter *adap = priv;
|
|
if (command == XC5000_TUNER_RESET) {
|
/* Reset the tuner */
|
dib0700_set_gpio(adap->dev, GPIO1, GPIO_OUT, 0);
|
msleep(10);
|
dib0700_set_gpio(adap->dev, GPIO1, GPIO_OUT, 1);
|
msleep(10);
|
} else {
|
err("xc5000: unknown tuner callback command: %d\n", command);
|
return -EINVAL;
|
}
|
|
return 0;
|
}
|
|
static struct xc5000_config s5h1411_xc5000_tunerconfig = {
|
.i2c_address = 0x64,
|
.if_khz = 5380,
|
};
|
|
static int xc5000_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
/* FIXME: generalize & move to common area */
|
adap->fe_adap[0].fe->callback = dib0700_xc5000_tuner_callback;
|
|
return dvb_attach(xc5000_attach, adap->fe_adap[0].fe, &adap->dev->i2c_adap,
|
&s5h1411_xc5000_tunerconfig)
|
== NULL ? -ENODEV : 0;
|
}
|
|
static int dib0700_xc4000_tuner_callback(void *priv, int component,
|
int command, int arg)
|
{
|
struct dvb_usb_adapter *adap = priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (command == XC4000_TUNER_RESET) {
|
/* Reset the tuner */
|
state->dib7000p_ops.set_gpio(adap->fe_adap[0].fe, 8, 0, 0);
|
msleep(10);
|
state->dib7000p_ops.set_gpio(adap->fe_adap[0].fe, 8, 0, 1);
|
} else {
|
err("xc4000: unknown tuner callback command: %d\n", command);
|
return -EINVAL;
|
}
|
|
return 0;
|
}
|
|
static struct dibx000_agc_config stk7700p_7000p_xc4000_agc_config = {
|
.band_caps = BAND_UHF | BAND_VHF,
|
.setup = 0x64,
|
.inv_gain = 0x02c8,
|
.time_stabiliz = 0x15,
|
.alpha_level = 0x00,
|
.thlock = 0x76,
|
.wbd_inv = 0x01,
|
.wbd_ref = 0x0b33,
|
.wbd_sel = 0x00,
|
.wbd_alpha = 0x02,
|
.agc1_max = 0x00,
|
.agc1_min = 0x00,
|
.agc2_max = 0x9b26,
|
.agc2_min = 0x26ca,
|
.agc1_pt1 = 0x00,
|
.agc1_pt2 = 0x00,
|
.agc1_pt3 = 0x00,
|
.agc1_slope1 = 0x00,
|
.agc1_slope2 = 0x00,
|
.agc2_pt1 = 0x00,
|
.agc2_pt2 = 0x80,
|
.agc2_slope1 = 0x1d,
|
.agc2_slope2 = 0x1d,
|
.alpha_mant = 0x11,
|
.alpha_exp = 0x1b,
|
.beta_mant = 0x17,
|
.beta_exp = 0x33,
|
.perform_agc_softsplit = 0x00,
|
};
|
|
static struct dibx000_bandwidth_config stk7700p_xc4000_pll_config = {
|
.internal = 60000,
|
.sampling = 30000,
|
.pll_prediv = 1,
|
.pll_ratio = 8,
|
.pll_range = 3,
|
.pll_reset = 1,
|
.pll_bypass = 0,
|
.enable_refdiv = 0,
|
.bypclk_div = 0,
|
.IO_CLK_en_core = 1,
|
.ADClkSrc = 1,
|
.modulo = 0,
|
.sad_cfg = (3 << 14) | (1 << 12) | 524, /* sad_cfg: refsel, sel, freq_15k */
|
.ifreq = 39370534,
|
.timf = 20452225,
|
.xtal_hz = 30000000
|
};
|
|
/* FIXME: none of these inputs are validated yet */
|
static struct dib7000p_config pctv_340e_config = {
|
.output_mpeg2_in_188_bytes = 1,
|
|
.agc_config_count = 1,
|
.agc = &stk7700p_7000p_xc4000_agc_config,
|
.bw = &stk7700p_xc4000_pll_config,
|
|
.gpio_dir = DIB7000M_GPIO_DEFAULT_DIRECTIONS,
|
.gpio_val = DIB7000M_GPIO_DEFAULT_VALUES,
|
.gpio_pwm_pos = DIB7000M_GPIO_DEFAULT_PWM_POS,
|
};
|
|
/* PCTV 340e GPIOs map:
|
dib0700:
|
GPIO2 - CX25843 sleep
|
GPIO3 - CS5340 reset
|
GPIO5 - IRD
|
GPIO6 - Power Supply
|
GPIO8 - LNA (1=off 0=on)
|
GPIO10 - CX25843 reset
|
dib7000:
|
GPIO8 - xc4000 reset
|
*/
|
static int pctv340e_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_state *st = adap->dev->priv;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
if (!dvb_attach(dib7000p_attach, &state->dib7000p_ops))
|
return -ENODEV;
|
|
/* Power Supply on */
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0);
|
msleep(50);
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(100); /* Allow power supply to settle before probing */
|
|
/* cx25843 reset */
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
msleep(1); /* cx25843 datasheet say 350us required */
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
|
/* LNA off for now */
|
dib0700_set_gpio(adap->dev, GPIO8, GPIO_OUT, 1);
|
|
/* Put the CX25843 to sleep for now since we're in digital mode */
|
dib0700_set_gpio(adap->dev, GPIO2, GPIO_OUT, 1);
|
|
/* FIXME: not verified yet */
|
dib0700_ctrl_clock(adap->dev, 72, 1);
|
|
msleep(500);
|
|
if (state->dib7000p_ops.dib7000pc_detection(&adap->dev->i2c_adap) == 0) {
|
/* Demodulator not found for some reason? */
|
dvb_detach(state->dib7000p_ops.set_wbd_ref);
|
return -ENODEV;
|
}
|
|
adap->fe_adap[0].fe = state->dib7000p_ops.init(&adap->dev->i2c_adap, 0x12,
|
&pctv_340e_config);
|
st->is_dib7000pc = 1;
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static struct xc4000_config dib7000p_xc4000_tunerconfig = {
|
.i2c_address = 0x61,
|
.default_pm = 1,
|
.dvb_amplitude = 0,
|
.set_smoothedcvbs = 0,
|
.if_khz = 5400
|
};
|
|
static int xc4000_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
struct i2c_adapter *tun_i2c;
|
struct dib0700_adapter_state *state = adap->priv;
|
|
/* The xc4000 is not on the main i2c bus */
|
tun_i2c = state->dib7000p_ops.get_i2c_master(adap->fe_adap[0].fe,
|
DIBX000_I2C_INTERFACE_TUNER, 1);
|
if (tun_i2c == NULL) {
|
printk(KERN_ERR "Could not reach tuner i2c bus\n");
|
return 0;
|
}
|
|
/* Setup the reset callback */
|
adap->fe_adap[0].fe->callback = dib0700_xc4000_tuner_callback;
|
|
return dvb_attach(xc4000_attach, adap->fe_adap[0].fe, tun_i2c,
|
&dib7000p_xc4000_tunerconfig)
|
== NULL ? -ENODEV : 0;
|
}
|
|
static struct lgdt3305_config hcw_lgdt3305_config = {
|
.i2c_addr = 0x0e,
|
.mpeg_mode = LGDT3305_MPEG_PARALLEL,
|
.tpclk_edge = LGDT3305_TPCLK_FALLING_EDGE,
|
.tpvalid_polarity = LGDT3305_TP_VALID_LOW,
|
.deny_i2c_rptr = 0,
|
.spectral_inversion = 1,
|
.qam_if_khz = 6000,
|
.vsb_if_khz = 6000,
|
.usref_8vsb = 0x0500,
|
};
|
|
static struct mxl5007t_config hcw_mxl5007t_config = {
|
.xtal_freq_hz = MxL_XTAL_25_MHZ,
|
.if_freq_hz = MxL_IF_6_MHZ,
|
.invert_if = 1,
|
};
|
|
/* TIGER-ATSC map:
|
GPIO0 - LNA_CTR (H: LNA power enabled, L: LNA power disabled)
|
GPIO1 - ANT_SEL (H: VPA, L: MCX)
|
GPIO4 - SCL2
|
GPIO6 - EN_TUNER
|
GPIO7 - SDA2
|
GPIO10 - DEM_RST
|
|
MXL is behind LG's i2c repeater. LG is on SCL2/SDA2 gpios on the DIB
|
*/
|
static int lgdt3305_frontend_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_state *st = adap->dev->priv;
|
|
/* Make use of the new i2c functions from FW 1.20 */
|
st->fw_use_new_i2c_api = 1;
|
|
st->disable_streaming_master_mode = 1;
|
|
/* fe power enable */
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0);
|
msleep(30);
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(30);
|
|
/* demod reset */
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(30);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
msleep(30);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(30);
|
|
adap->fe_adap[0].fe = dvb_attach(lgdt3305_attach,
|
&hcw_lgdt3305_config,
|
&adap->dev->i2c_adap);
|
|
return adap->fe_adap[0].fe == NULL ? -ENODEV : 0;
|
}
|
|
static int mxl5007t_tuner_attach(struct dvb_usb_adapter *adap)
|
{
|
return dvb_attach(mxl5007t_attach, adap->fe_adap[0].fe,
|
&adap->dev->i2c_adap, 0x60,
|
&hcw_mxl5007t_config) == NULL ? -ENODEV : 0;
|
}
|
|
static int xbox_one_attach(struct dvb_usb_adapter *adap)
|
{
|
struct dib0700_state *st = adap->dev->priv;
|
struct i2c_client *client_demod, *client_tuner;
|
struct dvb_usb_device *d = adap->dev;
|
struct mn88472_config mn88472_config = { };
|
struct tda18250_config tda18250_config;
|
struct i2c_board_info info;
|
|
st->fw_use_new_i2c_api = 1;
|
st->disable_streaming_master_mode = 1;
|
|
/* fe power enable */
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0);
|
msleep(30);
|
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
|
msleep(30);
|
|
/* demod reset */
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(30);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
|
msleep(30);
|
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
|
msleep(30);
|
|
/* attach demod */
|
mn88472_config.fe = &adap->fe_adap[0].fe;
|
mn88472_config.i2c_wr_max = 22;
|
mn88472_config.xtal = 20500000;
|
mn88472_config.ts_mode = PARALLEL_TS_MODE;
|
mn88472_config.ts_clock = FIXED_TS_CLOCK;
|
memset(&info, 0, sizeof(struct i2c_board_info));
|
strscpy(info.type, "mn88472", I2C_NAME_SIZE);
|
info.addr = 0x18;
|
info.platform_data = &mn88472_config;
|
request_module(info.type);
|
client_demod = i2c_new_client_device(&d->i2c_adap, &info);
|
if (!i2c_client_has_driver(client_demod))
|
goto fail_demod_device;
|
if (!try_module_get(client_demod->dev.driver->owner))
|
goto fail_demod_module;
|
|
st->i2c_client_demod = client_demod;
|
|
adap->fe_adap[0].fe = mn88472_config.get_dvb_frontend(client_demod);
|
|
/* attach tuner */
|
memset(&tda18250_config, 0, sizeof(tda18250_config));
|
tda18250_config.if_dvbt_6 = 3950;
|
tda18250_config.if_dvbt_7 = 4450;
|
tda18250_config.if_dvbt_8 = 4950;
|
tda18250_config.if_dvbc_6 = 4950;
|
tda18250_config.if_dvbc_8 = 4950;
|
tda18250_config.if_atsc = 4079;
|
tda18250_config.loopthrough = true;
|
tda18250_config.xtal_freq = TDA18250_XTAL_FREQ_27MHZ;
|
tda18250_config.fe = adap->fe_adap[0].fe;
|
|
memset(&info, 0, sizeof(struct i2c_board_info));
|
strscpy(info.type, "tda18250", I2C_NAME_SIZE);
|
info.addr = 0x60;
|
info.platform_data = &tda18250_config;
|
|
request_module(info.type);
|
client_tuner = i2c_new_client_device(&adap->dev->i2c_adap, &info);
|
if (!i2c_client_has_driver(client_tuner))
|
goto fail_tuner_device;
|
if (!try_module_get(client_tuner->dev.driver->owner))
|
goto fail_tuner_module;
|
|
st->i2c_client_tuner = client_tuner;
|
return 0;
|
|
fail_tuner_module:
|
i2c_unregister_device(client_tuner);
|
fail_tuner_device:
|
module_put(client_demod->dev.driver->owner);
|
fail_demod_module:
|
i2c_unregister_device(client_demod);
|
fail_demod_device:
|
return -ENODEV;
|
}
|
|
|
/* DVB-USB and USB stuff follows */
|
struct usb_device_id dib0700_usb_id_table[] = {
|
/* 0 */ { USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK7700P) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK7700P_PC) },
|
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_500) },
|
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_500_2) },
|
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_STICK) },
|
/* 5 */ { USB_DEVICE(USB_VID_AVERMEDIA, USB_PID_AVERMEDIA_VOLAR) },
|
{ USB_DEVICE(USB_VID_COMPRO, USB_PID_COMPRO_VIDEOMATE_U500) },
|
{ USB_DEVICE(USB_VID_UNIWILL, USB_PID_UNIWILL_STK7700P) },
|
{ USB_DEVICE(USB_VID_LEADTEK, USB_PID_WINFAST_DTV_DONGLE_STK7700P) },
|
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_STICK_2) },
|
/* 10 */{ USB_DEVICE(USB_VID_AVERMEDIA, USB_PID_AVERMEDIA_VOLAR_2) },
|
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV2000E) },
|
{ USB_DEVICE(USB_VID_TERRATEC,
|
USB_PID_TERRATEC_CINERGY_DT_XS_DIVERSITY) },
|
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_TD_STICK) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK7700D) },
|
/* 15 */{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK7070P) },
|
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV_DVB_T_FLASH) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK7070PD) },
|
{ USB_DEVICE(USB_VID_PINNACLE,
|
USB_PID_PINNACLE_PCTV_DUAL_DIVERSITY_DVB_T) },
|
{ USB_DEVICE(USB_VID_COMPRO, USB_PID_COMPRO_VIDEOMATE_U500_PC) },
|
/* 20 */{ USB_DEVICE(USB_VID_AVERMEDIA, USB_PID_AVERMEDIA_EXPRESS) },
|
{ USB_DEVICE(USB_VID_GIGABYTE, USB_PID_GIGABYTE_U7000) },
|
{ USB_DEVICE(USB_VID_ULTIMA_ELECTRONIC, USB_PID_ARTEC_T14BR) },
|
{ USB_DEVICE(USB_VID_ASUS, USB_PID_ASUS_U3000) },
|
{ USB_DEVICE(USB_VID_ASUS, USB_PID_ASUS_U3100) },
|
/* 25 */{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_STICK_3) },
|
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_MYTV_T) },
|
{ USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_CINERGY_HT_USB_XE) },
|
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_EXPRESSCARD_320CX) },
|
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV72E) },
|
/* 30 */{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV73E) },
|
{ USB_DEVICE(USB_VID_YUAN, USB_PID_YUAN_EC372S) },
|
{ USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_CINERGY_HT_EXPRESS) },
|
{ USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_CINERGY_T_XXS) },
|
{ USB_DEVICE(USB_VID_LEADTEK, USB_PID_WINFAST_DTV_DONGLE_STK7700P_2) },
|
/* 35 */{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_TD_STICK_52009) },
|
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_500_3) },
|
{ USB_DEVICE(USB_VID_GIGABYTE, USB_PID_GIGABYTE_U8000) },
|
{ USB_DEVICE(USB_VID_YUAN, USB_PID_YUAN_STK7700PH) },
|
{ USB_DEVICE(USB_VID_ASUS, USB_PID_ASUS_U3000H) },
|
/* 40 */{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV801E) },
|
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV801E_SE) },
|
{ USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_CINERGY_T_EXPRESS) },
|
{ USB_DEVICE(USB_VID_TERRATEC,
|
USB_PID_TERRATEC_CINERGY_DT_XS_DIVERSITY_2) },
|
{ USB_DEVICE(USB_VID_SONY, USB_PID_SONY_PLAYTV) },
|
/* 45 */{ USB_DEVICE(USB_VID_YUAN, USB_PID_YUAN_PD378S) },
|
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_TIGER_ATSC) },
|
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_TIGER_ATSC_B210) },
|
{ USB_DEVICE(USB_VID_YUAN, USB_PID_YUAN_MC770) },
|
{ USB_DEVICE(USB_VID_ELGATO, USB_PID_ELGATO_EYETV_DTT) },
|
/* 50 */{ USB_DEVICE(USB_VID_ELGATO, USB_PID_ELGATO_EYETV_DTT_Dlx) },
|
{ USB_DEVICE(USB_VID_LEADTEK, USB_PID_WINFAST_DTV_DONGLE_H) },
|
{ USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_T3) },
|
{ USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_T5) },
|
{ USB_DEVICE(USB_VID_YUAN, USB_PID_YUAN_STK7700D) },
|
/* 55 */{ USB_DEVICE(USB_VID_YUAN, USB_PID_YUAN_STK7700D_2) },
|
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV73A) },
|
{ USB_DEVICE(USB_VID_PCTV, USB_PID_PINNACLE_PCTV73ESE) },
|
{ USB_DEVICE(USB_VID_PCTV, USB_PID_PINNACLE_PCTV282E) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK7770P) },
|
/* 60 */{ USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_CINERGY_T_XXS_2) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK807XPVR) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK807XP) },
|
{ USB_DEVICE_VER(USB_VID_PIXELVIEW, USB_PID_PIXELVIEW_SBTVD, 0x000, 0x3f00) },
|
{ USB_DEVICE(USB_VID_EVOLUTEPC, USB_PID_TVWAY_PLUS) },
|
/* 65 */{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV73ESE) },
|
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV282E) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK8096GP) },
|
{ USB_DEVICE(USB_VID_ELGATO, USB_PID_ELGATO_EYETV_DIVERSITY) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_NIM9090M) },
|
/* 70 */{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_NIM8096MD) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_NIM9090MD) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_NIM7090) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_TFE7090PVR) },
|
{ USB_DEVICE(USB_VID_TECHNISAT, USB_PID_TECHNISAT_AIRSTAR_TELESTICK_2) },
|
/* 75 */{ USB_DEVICE(USB_VID_MEDION, USB_PID_CREATIX_CTX1921) },
|
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV340E) },
|
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV340E_SE) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_TFE7790P) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_TFE8096P) },
|
/* 80 */{ USB_DEVICE(USB_VID_ELGATO, USB_PID_ELGATO_EYETV_DTT_2) },
|
{ USB_DEVICE(USB_VID_PCTV, USB_PID_PCTV_2002E) },
|
{ USB_DEVICE(USB_VID_PCTV, USB_PID_PCTV_2002E_SE) },
|
{ USB_DEVICE(USB_VID_PCTV, USB_PID_DIBCOM_STK8096PVR) },
|
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK8096PVR) },
|
/* 85 */{ USB_DEVICE(USB_VID_HAMA, USB_PID_HAMA_DVBT_HYBRID) },
|
{ USB_DEVICE(USB_VID_MICROSOFT, USB_PID_XBOX_ONE_TUNER) },
|
{ 0 } /* Terminating entry */
|
};
|
MODULE_DEVICE_TABLE(usb, dib0700_usb_id_table);
|
|
#define DIB0700_DEFAULT_DEVICE_PROPERTIES \
|
.caps = DVB_USB_IS_AN_I2C_ADAPTER, \
|
.usb_ctrl = DEVICE_SPECIFIC, \
|
.firmware = "dvb-usb-dib0700-1.20.fw", \
|
.download_firmware = dib0700_download_firmware, \
|
.no_reconnect = 1, \
|
.size_of_priv = sizeof(struct dib0700_state), \
|
.i2c_algo = &dib0700_i2c_algo, \
|
.identify_state = dib0700_identify_state
|
|
#define DIB0700_DEFAULT_STREAMING_CONFIG(ep) \
|
.streaming_ctrl = dib0700_streaming_ctrl, \
|
.stream = { \
|
.type = USB_BULK, \
|
.count = 4, \
|
.endpoint = ep, \
|
.u = { \
|
.bulk = { \
|
.buffersize = 39480, \
|
} \
|
} \
|
}
|
|
#define DIB0700_NUM_FRONTENDS(n) \
|
.num_frontends = n, \
|
.size_of_priv = sizeof(struct dib0700_adapter_state)
|
|
struct dvb_usb_device_properties dib0700_devices[] = {
|
{
|
DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk7700p_pid_filter,
|
.pid_filter_ctrl = stk7700p_pid_filter_ctrl,
|
.frontend_attach = stk7700p_frontend_attach,
|
.tuner_attach = stk7700p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 8,
|
.devices = {
|
{ "DiBcom STK7700P reference design",
|
{ &dib0700_usb_id_table[0], &dib0700_usb_id_table[1] },
|
{ NULL },
|
},
|
{ "Hauppauge Nova-T Stick",
|
{ &dib0700_usb_id_table[4], &dib0700_usb_id_table[9], NULL },
|
{ NULL },
|
},
|
{ "AVerMedia AVerTV DVB-T Volar",
|
{ &dib0700_usb_id_table[5], &dib0700_usb_id_table[10] },
|
{ NULL },
|
},
|
{ "Compro Videomate U500",
|
{ &dib0700_usb_id_table[6], &dib0700_usb_id_table[19] },
|
{ NULL },
|
},
|
{ "Uniwill STK7700P based (Hama and others)",
|
{ &dib0700_usb_id_table[7], NULL },
|
{ NULL },
|
},
|
{ "Leadtek Winfast DTV Dongle (STK7700P based)",
|
{ &dib0700_usb_id_table[8], &dib0700_usb_id_table[34] },
|
{ NULL },
|
},
|
{ "AVerMedia AVerTV DVB-T Express",
|
{ &dib0700_usb_id_table[20] },
|
{ NULL },
|
},
|
{ "Gigabyte U7000",
|
{ &dib0700_usb_id_table[21], NULL },
|
{ NULL },
|
}
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
|
.num_adapters = 2,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.frontend_attach = bristol_frontend_attach,
|
.tuner_attach = bristol_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
}, {
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.frontend_attach = bristol_frontend_attach,
|
.tuner_attach = bristol_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
|
}},
|
}
|
},
|
|
.num_device_descs = 1,
|
.devices = {
|
{ "Hauppauge Nova-T 500 Dual DVB-T",
|
{ &dib0700_usb_id_table[2], &dib0700_usb_id_table[3], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
|
.num_adapters = 2,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = stk7700d_frontend_attach,
|
.tuner_attach = stk7700d_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
}, {
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = stk7700d_frontend_attach,
|
.tuner_attach = stk7700d_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
|
}},
|
}
|
},
|
|
.num_device_descs = 5,
|
.devices = {
|
{ "Pinnacle PCTV 2000e",
|
{ &dib0700_usb_id_table[11], NULL },
|
{ NULL },
|
},
|
{ "Terratec Cinergy DT XS Diversity",
|
{ &dib0700_usb_id_table[12], NULL },
|
{ NULL },
|
},
|
{ "Hauppauge Nova-TD Stick/Elgato Eye-TV Diversity",
|
{ &dib0700_usb_id_table[13], NULL },
|
{ NULL },
|
},
|
{ "DiBcom STK7700D reference design",
|
{ &dib0700_usb_id_table[14], NULL },
|
{ NULL },
|
},
|
{ "YUAN High-Tech DiBcom STK7700D",
|
{ &dib0700_usb_id_table[55], NULL },
|
{ NULL },
|
},
|
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = stk7700P2_frontend_attach,
|
.tuner_attach = stk7700d_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 3,
|
.devices = {
|
{ "ASUS My Cinema U3000 Mini DVBT Tuner",
|
{ &dib0700_usb_id_table[23], NULL },
|
{ NULL },
|
},
|
{ "Yuan EC372S",
|
{ &dib0700_usb_id_table[31], NULL },
|
{ NULL },
|
},
|
{ "Terratec Cinergy T Express",
|
{ &dib0700_usb_id_table[42], NULL },
|
{ NULL },
|
}
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = stk7070p_frontend_attach,
|
.tuner_attach = dib7070p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 12,
|
.devices = {
|
{ "DiBcom STK7070P reference design",
|
{ &dib0700_usb_id_table[15], NULL },
|
{ NULL },
|
},
|
{ "Pinnacle PCTV DVB-T Flash Stick",
|
{ &dib0700_usb_id_table[16], NULL },
|
{ NULL },
|
},
|
{ "Artec T14BR DVB-T",
|
{ &dib0700_usb_id_table[22], NULL },
|
{ NULL },
|
},
|
{ "ASUS My Cinema U3100 Mini DVBT Tuner",
|
{ &dib0700_usb_id_table[24], NULL },
|
{ NULL },
|
},
|
{ "Hauppauge Nova-T Stick",
|
{ &dib0700_usb_id_table[25], NULL },
|
{ NULL },
|
},
|
{ "Hauppauge Nova-T MyTV.t",
|
{ &dib0700_usb_id_table[26], NULL },
|
{ NULL },
|
},
|
{ "Pinnacle PCTV 72e",
|
{ &dib0700_usb_id_table[29], NULL },
|
{ NULL },
|
},
|
{ "Pinnacle PCTV 73e",
|
{ &dib0700_usb_id_table[30], NULL },
|
{ NULL },
|
},
|
{ "Elgato EyeTV DTT",
|
{ &dib0700_usb_id_table[49], NULL },
|
{ NULL },
|
},
|
{ "Yuan PD378S",
|
{ &dib0700_usb_id_table[45], NULL },
|
{ NULL },
|
},
|
{ "Elgato EyeTV Dtt Dlx PD378S",
|
{ &dib0700_usb_id_table[50], NULL },
|
{ NULL },
|
},
|
{ "Elgato EyeTV DTT rev. 2",
|
{ &dib0700_usb_id_table[80], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = stk7070p_frontend_attach,
|
.tuner_attach = dib7070p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 3,
|
.devices = {
|
{ "Pinnacle PCTV 73A",
|
{ &dib0700_usb_id_table[56], NULL },
|
{ NULL },
|
},
|
{ "Pinnacle PCTV 73e SE",
|
{ &dib0700_usb_id_table[57], &dib0700_usb_id_table[65], NULL },
|
{ NULL },
|
},
|
{ "Pinnacle PCTV 282e",
|
{ &dib0700_usb_id_table[58], &dib0700_usb_id_table[66], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
|
.num_adapters = 2,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = novatd_frontend_attach,
|
.tuner_attach = dib7070p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
}, {
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = novatd_frontend_attach,
|
.tuner_attach = dib7070p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
|
}},
|
}
|
},
|
|
.num_device_descs = 3,
|
.devices = {
|
{ "Hauppauge Nova-TD Stick (52009)",
|
{ &dib0700_usb_id_table[35], NULL },
|
{ NULL },
|
},
|
{ "PCTV 2002e",
|
{ &dib0700_usb_id_table[81], NULL },
|
{ NULL },
|
},
|
{ "PCTV 2002e SE",
|
{ &dib0700_usb_id_table[82], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
|
.num_adapters = 2,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = stk7070pd_frontend_attach0,
|
.tuner_attach = dib7070p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
}, {
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = stk7070pd_frontend_attach1,
|
.tuner_attach = dib7070p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
|
}},
|
}
|
},
|
|
.num_device_descs = 5,
|
.devices = {
|
{ "DiBcom STK7070PD reference design",
|
{ &dib0700_usb_id_table[17], NULL },
|
{ NULL },
|
},
|
{ "Pinnacle PCTV Dual DVB-T Diversity Stick",
|
{ &dib0700_usb_id_table[18], NULL },
|
{ NULL },
|
},
|
{ "Hauppauge Nova-TD-500 (84xxx)",
|
{ &dib0700_usb_id_table[36], NULL },
|
{ NULL },
|
},
|
{ "Terratec Cinergy DT USB XS Diversity/ T5",
|
{ &dib0700_usb_id_table[43],
|
&dib0700_usb_id_table[53], NULL},
|
{ NULL },
|
},
|
{ "Sony PlayTV",
|
{ &dib0700_usb_id_table[44], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
|
.num_adapters = 2,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = stk7070pd_frontend_attach0,
|
.tuner_attach = dib7070p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
}, {
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = stk7070pd_frontend_attach1,
|
.tuner_attach = dib7070p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
|
}},
|
}
|
},
|
|
.num_device_descs = 1,
|
.devices = {
|
{ "Elgato EyeTV Diversity",
|
{ &dib0700_usb_id_table[68], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_NEC_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = stk7700ph_frontend_attach,
|
.tuner_attach = stk7700ph_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 10,
|
.devices = {
|
{ "Terratec Cinergy HT USB XE",
|
{ &dib0700_usb_id_table[27], NULL },
|
{ NULL },
|
},
|
{ "Pinnacle Expresscard 320cx",
|
{ &dib0700_usb_id_table[28], NULL },
|
{ NULL },
|
},
|
{ "Terratec Cinergy HT Express",
|
{ &dib0700_usb_id_table[32], NULL },
|
{ NULL },
|
},
|
{ "Gigabyte U8000-RH",
|
{ &dib0700_usb_id_table[37], NULL },
|
{ NULL },
|
},
|
{ "YUAN High-Tech STK7700PH",
|
{ &dib0700_usb_id_table[38], NULL },
|
{ NULL },
|
},
|
{ "Asus My Cinema-U3000Hybrid",
|
{ &dib0700_usb_id_table[39], NULL },
|
{ NULL },
|
},
|
{ "YUAN High-Tech MC770",
|
{ &dib0700_usb_id_table[48], NULL },
|
{ NULL },
|
},
|
{ "Leadtek WinFast DTV Dongle H",
|
{ &dib0700_usb_id_table[51], NULL },
|
{ NULL },
|
},
|
{ "YUAN High-Tech STK7700D",
|
{ &dib0700_usb_id_table[54], NULL },
|
{ NULL },
|
},
|
{ "Hama DVB=T Hybrid USB Stick",
|
{ &dib0700_usb_id_table[85], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.frontend_attach = s5h1411_frontend_attach,
|
.tuner_attach = xc5000_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 2,
|
.devices = {
|
{ "Pinnacle PCTV HD Pro USB Stick",
|
{ &dib0700_usb_id_table[40], NULL },
|
{ NULL },
|
},
|
{ "Pinnacle PCTV HD USB Stick",
|
{ &dib0700_usb_id_table[41], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.frontend_attach = lgdt3305_frontend_attach,
|
.tuner_attach = mxl5007t_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 2,
|
.devices = {
|
{ "Hauppauge ATSC MiniCard (B200)",
|
{ &dib0700_usb_id_table[46], NULL },
|
{ NULL },
|
},
|
{ "Hauppauge ATSC MiniCard (B210)",
|
{ &dib0700_usb_id_table[47], NULL },
|
{ NULL },
|
},
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = stk7770p_frontend_attach,
|
.tuner_attach = dib7770p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 4,
|
.devices = {
|
{ "DiBcom STK7770P reference design",
|
{ &dib0700_usb_id_table[59], NULL },
|
{ NULL },
|
},
|
{ "Terratec Cinergy T USB XXS (HD)/ T3",
|
{ &dib0700_usb_id_table[33],
|
&dib0700_usb_id_table[52],
|
&dib0700_usb_id_table[60], NULL},
|
{ NULL },
|
},
|
{ "TechniSat AirStar TeleStick 2",
|
{ &dib0700_usb_id_table[74], NULL },
|
{ NULL },
|
},
|
{ "Medion CTX1921 DVB-T USB",
|
{ &dib0700_usb_id_table[75], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk80xx_pid_filter,
|
.pid_filter_ctrl = stk80xx_pid_filter_ctrl,
|
.frontend_attach = stk807x_frontend_attach,
|
.tuner_attach = dib807x_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 3,
|
.devices = {
|
{ "DiBcom STK807xP reference design",
|
{ &dib0700_usb_id_table[62], NULL },
|
{ NULL },
|
},
|
{ "Prolink Pixelview SBTVD",
|
{ &dib0700_usb_id_table[63], NULL },
|
{ NULL },
|
},
|
{ "EvolutePC TVWay+",
|
{ &dib0700_usb_id_table[64], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_NEC_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 2,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk80xx_pid_filter,
|
.pid_filter_ctrl = stk80xx_pid_filter_ctrl,
|
.frontend_attach = stk807xpvr_frontend_attach0,
|
.tuner_attach = dib807x_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER | DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk80xx_pid_filter,
|
.pid_filter_ctrl = stk80xx_pid_filter_ctrl,
|
.frontend_attach = stk807xpvr_frontend_attach1,
|
.tuner_attach = dib807x_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
|
}},
|
},
|
},
|
|
.num_device_descs = 1,
|
.devices = {
|
{ "DiBcom STK807xPVR reference design",
|
{ &dib0700_usb_id_table[61], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER |
|
DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk80xx_pid_filter,
|
.pid_filter_ctrl = stk80xx_pid_filter_ctrl,
|
.frontend_attach = stk809x_frontend_attach,
|
.tuner_attach = dib809x_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 1,
|
.devices = {
|
{ "DiBcom STK8096GP reference design",
|
{ &dib0700_usb_id_table[67], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER |
|
DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = dib90x0_pid_filter,
|
.pid_filter_ctrl = dib90x0_pid_filter_ctrl,
|
.frontend_attach = stk9090m_frontend_attach,
|
.tuner_attach = dib9090_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 1,
|
.devices = {
|
{ "DiBcom STK9090M reference design",
|
{ &dib0700_usb_id_table[69], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER |
|
DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk80xx_pid_filter,
|
.pid_filter_ctrl = stk80xx_pid_filter_ctrl,
|
.frontend_attach = nim8096md_frontend_attach,
|
.tuner_attach = nim8096md_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 1,
|
.devices = {
|
{ "DiBcom NIM8096MD reference design",
|
{ &dib0700_usb_id_table[70], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER |
|
DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = dib90x0_pid_filter,
|
.pid_filter_ctrl = dib90x0_pid_filter_ctrl,
|
.frontend_attach = nim9090md_frontend_attach,
|
.tuner_attach = nim9090md_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 1,
|
.devices = {
|
{ "DiBcom NIM9090MD reference design",
|
{ &dib0700_usb_id_table[71], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER |
|
DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = nim7090_frontend_attach,
|
.tuner_attach = nim7090_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 1,
|
.devices = {
|
{ "DiBcom NIM7090 reference design",
|
{ &dib0700_usb_id_table[72], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 2,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER |
|
DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = tfe7090pvr_frontend0_attach,
|
.tuner_attach = tfe7090pvr_tuner0_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
|
}},
|
},
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER |
|
DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = tfe7090pvr_frontend1_attach,
|
.tuner_attach = tfe7090pvr_tuner1_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 1,
|
.devices = {
|
{ "DiBcom TFE7090PVR reference design",
|
{ &dib0700_usb_id_table[73], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.frontend_attach = pctv340e_frontend_attach,
|
.tuner_attach = xc4000_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
}},
|
},
|
},
|
|
.num_device_descs = 2,
|
.devices = {
|
{ "Pinnacle PCTV 340e HD Pro USB Stick",
|
{ &dib0700_usb_id_table[76], NULL },
|
{ NULL },
|
},
|
{ "Pinnacle PCTV Hybrid Stick Solo",
|
{ &dib0700_usb_id_table[77], NULL },
|
{ NULL },
|
},
|
},
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER |
|
DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk70x0p_pid_filter,
|
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
|
.frontend_attach = tfe7790p_frontend_attach,
|
.tuner_attach = tfe7790p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
|
} },
|
},
|
},
|
|
.num_device_descs = 1,
|
.devices = {
|
{ "DiBcom TFE7790P reference design",
|
{ &dib0700_usb_id_table[78], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER |
|
DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk80xx_pid_filter,
|
.pid_filter_ctrl = stk80xx_pid_filter_ctrl,
|
.frontend_attach = tfe8096p_frontend_attach,
|
.tuner_attach = tfe8096p_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
|
} },
|
},
|
},
|
|
.num_device_descs = 1,
|
.devices = {
|
{ "DiBcom TFE8096P reference design",
|
{ &dib0700_usb_id_table[79], NULL },
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 2,
|
.adapter = {
|
{
|
.num_frontends = 1,
|
.fe = {{
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER |
|
DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk80xx_pid_filter,
|
.pid_filter_ctrl = stk80xx_pid_filter_ctrl,
|
.frontend_attach = stk809x_frontend_attach,
|
.tuner_attach = dib809x_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
|
} },
|
.size_of_priv =
|
sizeof(struct dib0700_adapter_state),
|
}, {
|
.num_frontends = 1,
|
.fe = { {
|
.caps = DVB_USB_ADAP_HAS_PID_FILTER |
|
DVB_USB_ADAP_PID_FILTER_CAN_BE_TURNED_OFF,
|
.pid_filter_count = 32,
|
.pid_filter = stk80xx_pid_filter,
|
.pid_filter_ctrl = stk80xx_pid_filter_ctrl,
|
.frontend_attach = stk809x_frontend1_attach,
|
.tuner_attach = dib809x_tuner_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
|
} },
|
.size_of_priv =
|
sizeof(struct dib0700_adapter_state),
|
},
|
},
|
.num_device_descs = 1,
|
.devices = {
|
{ "DiBcom STK8096-PVR reference design",
|
{ &dib0700_usb_id_table[83],
|
&dib0700_usb_id_table[84], NULL},
|
{ NULL },
|
},
|
},
|
|
.rc.core = {
|
.rc_interval = DEFAULT_RC_INTERVAL,
|
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
|
.module_name = "dib0700",
|
.rc_query = dib0700_rc_query_old_firmware,
|
.allowed_protos = RC_PROTO_BIT_RC5 |
|
RC_PROTO_BIT_RC6_MCE |
|
RC_PROTO_BIT_NEC,
|
.change_protocol = dib0700_change_protocol,
|
},
|
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
|
.num_adapters = 1,
|
.adapter = {
|
{
|
DIB0700_NUM_FRONTENDS(1),
|
.fe = {{
|
.frontend_attach = xbox_one_attach,
|
|
DIB0700_DEFAULT_STREAMING_CONFIG(0x82),
|
} },
|
},
|
},
|
.num_device_descs = 1,
|
.devices = {
|
{ "Microsoft Xbox One Digital TV Tuner",
|
{ &dib0700_usb_id_table[86], NULL },
|
{ NULL },
|
},
|
},
|
},
|
};
|
|
int dib0700_device_count = ARRAY_SIZE(dib0700_devices);
|
