/*
|
* (C) Copyright 2008 Stefan Roese <sr@denx.de>, DENX Software Engineering
|
*
|
* SPDX-License-Identifier: GPL-2.0+
|
*/
|
|
/*
|
* This file contains the configuration parameters for the VCT board
|
* family:
|
*
|
* vct_premium
|
* vct_premium_small
|
* vct_premium_onenand
|
* vct_premium_onenand_small
|
* vct_platinum
|
* vct_platinum_small
|
* vct_platinum_onenand
|
* vct_platinum_onenand_small
|
* vct_platinumavc
|
* vct_platinumavc_small
|
* vct_platinumavc_onenand
|
* vct_platinumavc_onenand_small
|
*/
|
|
#ifndef __CONFIG_H
|
#define __CONFIG_H
|
|
#define CPU_CLOCK_RATE 324000000 /* Clock for the MIPS core */
|
#define CONFIG_SYS_MIPS_TIMER_FREQ (CPU_CLOCK_RATE / 2)
|
|
#define CONFIG_SKIP_LOWLEVEL_INIT /* SDRAM is initialized by the bootstrap code */
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
|
#define CONFIG_SYS_MALLOC_LEN (1 << 20)
|
#define CONFIG_SYS_BOOTPARAMS_LEN (128 << 10)
|
#define CONFIG_SYS_INIT_SP_OFFSET 0x400000
|
|
#if !defined(CONFIG_VCT_NAND) && !defined(CONFIG_VCT_ONENAND)
|
#define CONFIG_VCT_NOR
|
#endif
|
|
/*
|
* UART
|
*/
|
#ifdef CONFIG_VCT_PLATINUMAVC
|
#define UART_1_BASE 0xBDC30000
|
#else
|
#define UART_1_BASE 0xBF89C000
|
#endif
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
#define CONFIG_SYS_NS16550_REG_SIZE -4
|
#define CONFIG_SYS_NS16550_COM1 UART_1_BASE
|
#define CONFIG_CONS_INDEX 1
|
#define CONFIG_SYS_NS16550_CLK 921600
|
|
/*
|
* SDRAM
|
*/
|
#define CONFIG_SYS_SDRAM_BASE 0x80000000
|
#define CONFIG_SYS_MBYTES_SDRAM 128
|
#define CONFIG_SYS_MEMTEST_START 0x80200000
|
#define CONFIG_SYS_MEMTEST_END 0x80400000
|
#define CONFIG_SYS_LOAD_ADDR 0x80400000 /* default load address */
|
|
#if defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)
|
/*
|
* SMSC91C11x Network Card
|
*/
|
#define CONFIG_SMC911X
|
#define CONFIG_SMC911X_BASE 0x00000000
|
#define CONFIG_SMC911X_32_BIT
|
#define CONFIG_NET_RETRY_COUNT 20
|
#endif
|
|
/*
|
* Commands
|
*/
|
|
/*
|
* Only Premium/Platinum have ethernet support right now
|
*/
|
#if (defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)) && \
|
!defined(CONFIG_VCT_SMALL_IMAGE)
|
#endif
|
|
/*
|
* Only Premium/Platinum have USB-EHCI support right now
|
*/
|
#if (defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)) && \
|
!defined(CONFIG_VCT_SMALL_IMAGE)
|
#endif
|
|
#if defined(CONFIG_CMD_USB)
|
#define CONFIG_SUPPORT_VFAT
|
|
/*
|
* USB/EHCI
|
*/
|
#define CONFIG_USB_EHCI_VCT /* on VCT platform */
|
#define CONFIG_EHCI_MMIO_BIG_ENDIAN
|
#define CONFIG_EHCI_DESC_BIG_ENDIAN
|
#define CONFIG_EHCI_IS_TDI
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* re-init HCD after CMD_RESET */
|
#endif /* CONFIG_CMD_USB */
|
|
/*
|
* BOOTP options
|
*/
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
#define CONFIG_BOOTP_BOOTPATH
|
#define CONFIG_BOOTP_GATEWAY
|
#define CONFIG_BOOTP_HOSTNAME
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
/*
|
* Miscellaneous configurable options
|
*/
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
|
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
|
#define CONFIG_CMDLINE_EDITING /* add command line history */
|
|
/*
|
* FLASH and environment organization
|
*/
|
#if defined(CONFIG_VCT_NOR)
|
#define CONFIG_FLASH_NOT_MEM_MAPPED
|
|
/*
|
* We need special accessor functions for the CFI FLASH driver. This
|
* can be enabled via the CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS option.
|
*/
|
#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
|
|
/*
|
* For the non-memory-mapped NOR FLASH, we need to define the
|
* NOR FLASH area. This can't be detected via the addr2info()
|
* function, since we check for flash access in the very early
|
* U-Boot code, before the NOR FLASH is detected.
|
*/
|
#define CONFIG_FLASH_BASE 0xb0000000
|
#define CONFIG_FLASH_END 0xbfffffff
|
|
/*
|
* CFI driver settings
|
*/
|
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
|
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
|
#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* Use AMD (Spansion) reset cmd */
|
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT /* no byte writes on IXP4xx */
|
|
#define CONFIG_SYS_FLASH_BASE 0xb0000000
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
#ifdef CONFIG_ENV_IS_IN_FLASH
|
#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
|
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
|
|
/* Address and size of Redundant Environment Sector */
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
|
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
|
#endif /* CONFIG_ENV_IS_IN_FLASH */
|
#endif /* CONFIG_VCT_NOR */
|
|
#if defined(CONFIG_VCT_ONENAND)
|
#define CONFIG_USE_ONENAND_BOARD_INIT
|
#define CONFIG_SYS_ONENAND_BASE 0x00000000 /* this is not real address */
|
#define CONFIG_SYS_FLASH_BASE 0x00000000
|
#define CONFIG_ENV_ADDR (128 << 10) /* after compr. U-Boot image */
|
#define CONFIG_ENV_SIZE (128 << 10) /* erase size */
|
#endif /* CONFIG_VCT_ONENAND */
|
|
/*
|
* I2C/EEPROM
|
*/
|
#define CONFIG_SYS_I2C
|
#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
|
#define CONFIG_SYS_I2C_SOFT_SPEED 83000 /* 83 kHz is supposed to work */
|
#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7f
|
|
/*
|
* Software (bit-bang) I2C driver configuration
|
*/
|
#define CONFIG_SYS_GPIO_I2C_SCL 11
|
#define CONFIG_SYS_GPIO_I2C_SDA 10
|
|
#ifndef __ASSEMBLY__
|
int vct_gpio_dir(int pin, int dir);
|
void vct_gpio_set(int pin, int val);
|
int vct_gpio_get(int pin);
|
#endif
|
|
#define I2C_INIT vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SCL, 1)
|
#define I2C_ACTIVE vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SDA, 1)
|
#define I2C_TRISTATE vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SDA, 0)
|
#define I2C_READ vct_gpio_get(CONFIG_SYS_GPIO_I2C_SDA)
|
#define I2C_SDA(bit) vct_gpio_set(CONFIG_SYS_GPIO_I2C_SDA, bit)
|
#define I2C_SCL(bit) vct_gpio_set(CONFIG_SYS_GPIO_I2C_SCL, bit)
|
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
|
/* CAT24WC32 */
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */
|
/* 32 byte page write mode using*/
|
/* last 5 bits of the address */
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
|
|
#define CONFIG_BOOTCOMMAND "run test3"
|
|
/*
|
* UBI configuration
|
*/
|
|
/*
|
* We need a small, stripped down image to fit into the first 128k OneNAND
|
* erase block (gzipped). This image only needs basic commands for FLASH
|
* (NOR/OneNAND) usage and Linux kernel booting.
|
*/
|
#if defined(CONFIG_VCT_SMALL_IMAGE)
|
#undef CONFIG_SMC911X
|
#undef CONFIG_SYS_I2C_SOFT
|
#undef CONFIG_SOURCE
|
#undef CONFIG_SYS_LONGHELP
|
#undef CONFIG_TIMESTAMP
|
#endif /* CONFIG_VCT_SMALL_IMAGE */
|
|
#endif /* __CONFIG_H */
|
