/*
|
* BSD LICENSE
|
*
|
* Copyright(c) 2015 Broadcom Corporation. All rights reserved.
|
*
|
* Redistribution and use in source and binary forms, with or without
|
* modification, are permitted provided that the following conditions
|
* are met:
|
*
|
* * Redistributions of source code must retain the above copyright
|
* notice, this list of conditions and the following disclaimer.
|
* * Redistributions in binary form must reproduce the above copyright
|
* notice, this list of conditions and the following disclaimer in
|
* the documentation and/or other materials provided with the
|
* distribution.
|
* * Neither the name of Broadcom Corporation nor the names of its
|
* contributors may be used to endorse or promote products derived
|
* from this software without specific prior written permission.
|
*
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
|
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
|
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
|
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
|
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
*/
|
|
/dts-v1/;
|
|
#include "ns2.dtsi"
|
|
/ {
|
model = "Broadcom NS2 SVK";
|
compatible = "brcm,ns2-svk", "brcm,ns2";
|
|
aliases {
|
serial0 = &uart3;
|
serial1 = &uart0;
|
serial2 = &uart1;
|
serial3 = &uart2;
|
};
|
|
chosen {
|
stdout-path = "serial0:115200n8";
|
bootargs = "earlycon=uart8250,mmio32,0x66130000";
|
};
|
|
memory {
|
device_type = "memory";
|
reg = <0x000000000 0x80000000 0x00000000 0x40000000>;
|
};
|
};
|
|
&enet {
|
status = "okay";
|
};
|
|
&pci_phy0 {
|
status = "okay";
|
};
|
|
&pci_phy1 {
|
status = "okay";
|
};
|
|
&pcie0 {
|
status = "okay";
|
};
|
|
&pcie4 {
|
status = "okay";
|
};
|
|
&pcie8 {
|
status = "okay";
|
};
|
|
&i2c0 {
|
status = "okay";
|
};
|
|
&i2c1 {
|
status = "okay";
|
};
|
|
&uart0 {
|
status = "okay";
|
};
|
|
&uart1 {
|
status = "okay";
|
};
|
|
&uart2 {
|
status = "okay";
|
};
|
|
&uart3 {
|
status = "okay";
|
};
|
|
&ssp0 {
|
status = "okay";
|
|
slic@0 {
|
compatible = "silabs,si3226x";
|
reg = <0>;
|
spi-max-frequency = <5000000>;
|
spi-cpha;
|
spi-cpol;
|
pl022,hierarchy = <0>;
|
pl022,interface = <0>;
|
pl022,slave-tx-disable = <0>;
|
pl022,com-mode = <0>;
|
pl022,rx-level-trig = <1>;
|
pl022,tx-level-trig = <1>;
|
pl022,ctrl-len = <11>;
|
pl022,wait-state = <0>;
|
pl022,duplex = <0>;
|
};
|
};
|
|
&ssp1 {
|
status = "okay";
|
|
at25@0 {
|
compatible = "atmel,at25";
|
reg = <0>;
|
spi-max-frequency = <5000000>;
|
at25,byte-len = <0x8000>;
|
at25,addr-mode = <2>;
|
at25,page-size = <64>;
|
spi-cpha;
|
spi-cpol;
|
pl022,hierarchy = <0>;
|
pl022,interface = <0>;
|
pl022,slave-tx-disable = <0>;
|
pl022,com-mode = <0>;
|
pl022,rx-level-trig = <1>;
|
pl022,tx-level-trig = <1>;
|
pl022,ctrl-len = <11>;
|
pl022,wait-state = <0>;
|
pl022,duplex = <0>;
|
};
|
};
|
|
&sata_phy0 {
|
status = "okay";
|
};
|
|
&sata_phy1 {
|
status = "okay";
|
};
|
|
&sata {
|
status = "okay";
|
};
|
|
&sdio0 {
|
status = "okay";
|
};
|
|
&sdio1 {
|
status = "okay";
|
};
|
|
&nand {
|
nandcs@0 {
|
compatible = "brcm,nandcs";
|
reg = <0>;
|
nand-ecc-mode = "hw";
|
nand-ecc-strength = <8>;
|
nand-ecc-step-size = <512>;
|
nand-bus-width = <16>;
|
brcm,nand-oob-sector-size = <16>;
|
#address-cells = <1>;
|
#size-cells = <1>;
|
};
|
};
|
|
&mdio_mux_iproc {
|
mdio@10 {
|
gphy0: eth-phy@10 {
|
enet-phy-lane-swap;
|
reg = <0x10>;
|
};
|
};
|
};
|
|
&pinctrl {
|
pinctrl-names = "default";
|
pinctrl-0 = <&nand_sel>;
|
nand_sel: nand_sel {
|
function = "nand";
|
groups = "nand_grp";
|
};
|
};
|
|
&qspi {
|
bspi-sel = <0>;
|
flash: m25p80@0 {
|
#address-cells = <1>;
|
#size-cells = <1>;
|
compatible = "m25p80";
|
reg = <0x0>;
|
spi-max-frequency = <12500000>;
|
m25p,fast-read;
|
spi-cpol;
|
spi-cpha;
|
|
partition@0 {
|
label = "boot";
|
reg = <0x00000000 0x000a0000>;
|
};
|
|
partition@a0000 {
|
label = "env";
|
reg = <0x000a0000 0x00060000>;
|
};
|
|
partition@100000 {
|
label = "system";
|
reg = <0x00100000 0x00600000>;
|
};
|
|
partition@700000 {
|
label = "rootfs";
|
reg = <0x00700000 0x01900000>;
|
};
|
};
|
};
|
