* Rockchip AXI PCIe Endpoint Controller DT description
|
|
Required properties:
|
- compatible: Should contain "rockchip,rk3399-pcie-ep"
|
- reg: Two register ranges as listed in the reg-names property
|
- reg-names: Must include the following names
|
- "apb-base"
|
- "mem-base"
|
- clocks: Must contain an entry for each entry in clock-names.
|
See ../clocks/clock-bindings.txt for details.
|
- clock-names: Must include the following entries:
|
- "aclk"
|
- "aclk-perf"
|
- "hclk"
|
- "pm"
|
- resets: Must contain seven entries for each entry in reset-names.
|
See ../reset/reset.txt for details.
|
- reset-names: Must include the following names
|
- "core"
|
- "mgmt"
|
- "mgmt-sticky"
|
- "pipe"
|
- "pm"
|
- "aclk"
|
- "pclk"
|
- pinctrl-names : The pin control state names
|
- pinctrl-0: The "default" pinctrl state
|
- phys: Must contain an phandle to a PHY for each entry in phy-names.
|
- phy-names: Must include 4 entries for all 4 lanes even if some of
|
them won't be used for your cases. Entries are of the form "pcie-phy-N":
|
where N ranges from 0 to 3.
|
(see example below and you MUST also refer to ../phy/rockchip-pcie-phy.txt
|
for changing the #phy-cells of phy node to support it)
|
- rockchip,max-outbound-regions: Maximum number of outbound regions
|
|
Optional Property:
|
- num-lanes: number of lanes to use
|
- max-functions: Maximum number of functions that can be configured (default 1).
|
|
pcie0-ep: pcie@f8000000 {
|
compatible = "rockchip,rk3399-pcie-ep";
|
#address-cells = <3>;
|
#size-cells = <2>;
|
rockchip,max-outbound-regions = <16>;
|
clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>,
|
<&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>;
|
clock-names = "aclk", "aclk-perf",
|
"hclk", "pm";
|
max-functions = /bits/ 8 <8>;
|
num-lanes = <4>;
|
reg = <0x0 0xfd000000 0x0 0x1000000>, <0x0 0x80000000 0x0 0x20000>;
|
reg-names = "apb-base", "mem-base";
|
resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>,
|
<&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE> ,
|
<&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>;
|
reset-names = "core", "mgmt", "mgmt-sticky", "pipe",
|
"pm", "pclk", "aclk";
|
phys = <&pcie_phy 0>, <&pcie_phy 1>, <&pcie_phy 2>, <&pcie_phy 3>;
|
phy-names = "pcie-phy-0", "pcie-phy-1", "pcie-phy-2", "pcie-phy-3";
|
pinctrl-names = "default";
|
pinctrl-0 = <&pcie_clkreq>;
|
};
|
